![]() |
![]() |
#1 |
Registered User
![]() Join Date: Feb 2004
Location: brownfield texas (west texas)
Posts: 1,936
|
![]()
i wanted to swap some 5 stud 71 axles into my 68 6 stud rear end but it seems they are a bit longer. has any one done this and what does it require I dont relly want to change the whole rearend and not relly wanting to splurge 250.00 for aftermarket axles. whats the cheapest solution.
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jan 2002
Location: Slippery Rock PA USA
Posts: 1,692
|
...not much choice there almost gotta run the 71 rearend or redrill your axels...but be carefull redrilling them because i was going to redrill my 6 bolt axels to 5 on 4 3/4 so i could use the narrower rear but the center hub is 3 1/2" across and my wheels only have a 3" hole which is what the 5 bolt hubs are so i redrilled the 5 bolts.........
__________________
Ken Lyons, Slippery rock pa 68 short step 327 t10 4 gear 72 2wd blazer project 70 lwb 305/700r driver 78 caprice project 02 cavalier D.D ( hate it!!) |
![]() |
![]() |
![]() |
#3 | |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,977
|
Quote:
I've had them re-drilled & I've upgraded to replacement axles. Both ways work but remember these trucks often have many, many miles on them. If you spend the $$ to re-drill some old axles..... they'll still be old axles. If your making more HP/TQ than factory original, do yourself a favor & upgrade to new, better, aftermarket axles. If it's just a 6-banger/glide..... sure, re-drill 'em.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
![]() |
![]() |
![]() |
#4 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Some ppl have made spacers to take up the extra room, but I don't have the details on that.
Anyone? |
![]() |
![]() |
![]() |
#5 |
Account Suspended
Join Date: Dec 2003
Location: Texas
Posts: 2,686
|
Has anyone ever considered getting axles cut down and resplined.
They do that alot when they narrow them im told they can even cut the notch for a c clip I met phil66 and he had done the spacers on his 70 ? i think it was Not sure what he said he made them out of it but it looked clean. |
![]() |
![]() |
![]() |
#6 |
KEEP ON TRUCKING
Join Date: Sep 2000
Location: martinsville va
Posts: 2,563
|
i thought i seen the spacers on a vendors web site i think it was ricks not sure though
__________________
72 cheyenne 2wd lwb 71 k20 sons bassett va |
![]() |
![]() |
![]() |
#7 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Actually, i was refering to spacer as a piece os metal to move the whole backing plate 3/8 inch out on both sides...not wheel lug adapters.
|
![]() |
![]() |
![]() |
#8 |
Account Suspended
Join Date: Dec 2003
Location: Texas
Posts: 2,686
|
Thats what i was reffering too as well. Spacers to set the drums out.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|