Need a pic of inside of firewall with cable throttle - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Yukon Jack** · 05-05-2004, 10:34 AM

Now might be a good time to modify my cab from a gas pedal that uses the rod linkage to a cable linkage type. Can someone post a pic of the interior of the firewall showing how the cable linkage area is. I know there is a past post on this but I couldn't find it.

Stepsides 4Ever · 05-05-2004, 03:49 PM

I just went through that, at length. Here is the link

Unfortunately, the pictures were lost when Josh upgraded the board. Orange70Chevy helped me out with the pics and I only kept one of the ones that he posted, of the engine side of the firewall. Maybe you can PM him and ask him to post the one of the interior side.

Here is the pic of the engine side, with thanks to Orange70Chevy...

Stepsides 4Ever · 05-05-2004, 03:51 PM

...and here is a pic of the finished installation...

**Yukon Jack** · 05-05-2004, 03:58 PM

Thanks for the pics. I pm'd him to try to get the rest of the pics.

Stepsides 4Ever · 05-05-2004, 04:01 PM

...and, finally, the pic comparing the pedal I got out of a '71 (on the right) with the pedal that came out of a mid-'70s truck...

**Yukon Jack** · 05-05-2004, 04:09 PM

Hmm, I just happen to have a 78 parts truck in my barn right now. You used the later model pedal, correct?

Stepsides 4Ever · 05-06-2004, 03:04 AM

Yes, I used the later pedal. My intent was to not put any more holes in the firewall if I didn't have to, as well as maintaining the original pedal position. I have yet to weld up the holes where the original pedal came through the firewall (my attention is now on finishing the frame first, then I'll cherry out the firewall). I'm going to leave the rear light plug connector where it is (below the throttle cable)...it doesn't look like it will cause any interference problems.

Here is a pic of the "adapter plate". I made it out of 1/4" steel with both bolt patterns with the offset as mentioned in the earlier thread. I drilled and tapped 1/4-20 on the six holes (it's what I do for a living, so it didn't seem too arduous.) You don't have to go to all that trouble unless, like me, you like where the stock pedal resides...cable throttles are pretty forgiving.

Stepsides 4Ever · 05-06-2004, 03:09 AM

...and here is the pic showing where the new pedal is in relation to where the old pedal was...

05-05-2004, 10:34 AM	#1
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Need a pic of inside of firewall with cable throttle Now might be a good time to modify my cab from a gas pedal that uses the rod linkage to a cable linkage type. Can someone post a pic of the interior of the firewall showing how the cable linkage area is. I know there is a past post on this but I couldn't find it. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

05-05-2004, 03:49 PM	#2
Stepsides 4Ever Stepsides Are Bedder Join Date: Feb 2004 Location: Norco, CA Posts: 238	I just went through that, at length. Here is the link Unfortunately, the pictures were lost when Josh upgraded the board. Orange70Chevy helped me out with the pics and I only kept one of the ones that he posted, of the engine side of the firewall. Maybe you can PM him and ask him to post the one of the interior side. Here is the pic of the engine side, with thanks to Orange70Chevy... Attached Images

05-05-2004, 03:51 PM	#3
Stepsides 4Ever Stepsides Are Bedder Join Date: Feb 2004 Location: Norco, CA Posts: 238	...and here is a pic of the finished installation... Attached Images

05-05-2004, 03:58 PM	#4
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Thanks for the pics. I pm'd him to try to get the rest of the pics. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

05-05-2004, 04:01 PM	#5
Stepsides 4Ever Stepsides Are Bedder Join Date: Feb 2004 Location: Norco, CA Posts: 238	...and, finally, the pic comparing the pedal I got out of a '71 (on the right) with the pedal that came out of a mid-'70s truck... Attached Images

05-05-2004, 04:09 PM	#6
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Hmm, I just happen to have a 78 parts truck in my barn right now. You used the later model pedal, correct? __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

05-06-2004, 03:04 AM	#7
Stepsides 4Ever Stepsides Are Bedder Join Date: Feb 2004 Location: Norco, CA Posts: 238	Yes, I used the later pedal. My intent was to not put any more holes in the firewall if I didn't have to, as well as maintaining the original pedal position. I have yet to weld up the holes where the original pedal came through the firewall (my attention is now on finishing the frame first, then I'll cherry out the firewall). I'm going to leave the rear light plug connector where it is (below the throttle cable)...it doesn't look like it will cause any interference problems. Here is a pic of the "adapter plate". I made it out of 1/4" steel with both bolt patterns with the offset as mentioned in the earlier thread. I drilled and tapped 1/4-20 on the six holes (it's what I do for a living, so it didn't seem too arduous.) You don't have to go to all that trouble unless, like me, you like where the stock pedal resides...cable throttles are pretty forgiving. Attached Images

05-06-2004, 03:09 AM	#8
Stepsides 4Ever Stepsides Are Bedder Join Date: Feb 2004 Location: Norco, CA Posts: 238	...and here is the pic showing where the new pedal is in relation to where the old pedal was... Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.