NJ 67 C10 stepside - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**ScottH** · 06-23-2018, 11:24 PM

Just finished this project, was building it for a driver for myself but came across another I had been looking for. Lots of work done it including new suspension (drop springs & shocks all around), new steering (all ball joints, tie rods, idler arm, pitman arm), PS added, new exhaust, cooling system, etc.. Brake system was recently overhauled including lines, hoses, master, etc.. Installed a 327 w/10k miles on it from a 68 Camaro along with a 200R overdrive trans. Driveshaft professionally shortened with new ujoints. Body wise the floor boards were patched, rockers replaced, and new GM inner fender wells installed. Also new windshield, gasket, and wipers. Interior has new carpet, new seat cover (1 burnt spot from light), deluxe door panels with arm rests. Body does have a few rust spots (small area on door, rear fenders in lower front, have patch panel for worst side, and hood has rust in lip) & front fender has dent (called patina these days). I'm sure I am forgetting a few things. Runs great, does need alignment, clear NJ title in my name.

Best offer over $7500

**ScottH** · 07-02-2018, 10:45 AM

Best offer over 7500 takes it

**ScottH** · 07-16-2018, 12:57 AM

Sold

06-23-2018, 11:24 PM	#1
ScottH Senior Member Join Date: Sep 2002 Location: Hampstead, NC Posts: 8,190	67 C10 stepside Just finished this project, was building it for a driver for myself but came across another I had been looking for. Lots of work done it including new suspension (drop springs & shocks all around), new steering (all ball joints, tie rods, idler arm, pitman arm), PS added, new exhaust, cooling system, etc.. Brake system was recently overhauled including lines, hoses, master, etc.. Installed a 327 w/10k miles on it from a 68 Camaro along with a 200R overdrive trans. Driveshaft professionally shortened with new ujoints. Body wise the floor boards were patched, rockers replaced, and new GM inner fender wells installed. Also new windshield, gasket, and wipers. Interior has new carpet, new seat cover (1 burnt spot from light), deluxe door panels with arm rests. Body does have a few rust spots (small area on door, rear fenders in lower front, have patch panel for worst side, and hood has rust in lip) & front fender has dent (called patina these days). I'm sure I am forgetting a few things. Runs great, does need alignment, clear NJ title in my name. Best offer over $7500 Attached Images __________________ 1963 C10 swb fleetside 1966 GMC G1000 Handi-bus (future project) 1955 Chevy 2 dr. wagon Last edited by ScottH; 07-07-2018 at 08:50 AM.

07-02-2018, 10:45 AM	#2
ScottH Senior Member Join Date: Sep 2002 Location: Hampstead, NC Posts: 8,190	Re: 67 C10 stepside Best offer over 7500 takes it __________________ 1963 C10 swb fleetside 1966 GMC G1000 Handi-bus (future project) 1955 Chevy 2 dr. wagon

07-16-2018, 12:57 AM	#3
ScottH Senior Member Join Date: Sep 2002 Location: Hampstead, NC Posts: 8,190	Re: 67 C10 stepside Sold __________________ 1963 C10 swb fleetside 1966 GMC G1000 Handi-bus (future project) 1955 Chevy 2 dr. wagon



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.