|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-24-2018, 04:27 PM
|
#1 |
|
Registered User
Join Date: Jun 2018
Location: Indianapolis IN
Posts: 114
|
Master cylinder replace or paint?
So I'm dropping a new engine into this beast in a couple of weeks and will be working on cleaning up the wiring, AC and painting the compartment. I would like a shiny master cylinder too, but not sure if I should buy a new one, or if painting them is a decent idea. Appreciate the advice!
also, does anyone know where I can get a new Vehicle Emission Control Info sticker for the wheel well? |
|
|
|
07-24-2018, 04:32 PM
|
#2 |
|
Registered User
Join Date: May 2011
Location: Fort Pierce, FL
Posts: 430
|
Re: Master cylinder replace or paint?
Eastwood makes a paint for master cylinders that approximates the original finish, and it holds up well with little deterioration.
|
|
|
|
|
07-24-2018, 04:37 PM
|
#3 |
|
Registered User
Join Date: Jul 2009
Location: Space Coast, Fl.
Posts: 1,055
|
Re: Master cylinder replace or paint?
I've sprayed them with cast iron or rebuilder's gray paint. Look pretty new with a re-plated cap/cover.
__________________
Dad always said, "Son, WISH IN ONE HAND, and ......." -------------------------------------- -------------------------------------- Current toy trucks: '71 GMC 1500 SUPER CUSTOM short/step, orig. dk. blue, 350/700r, ps,pb, A/C '72 Blazer 2wd, ochre & white, 454, tremecTKO 500 5spd. ps, pb, A/C, tilt Last 10yrs of hobby vehicles, had a FEW more in the 50yrs. before these: '66 Plymouth Belvedere City of Miami cop car clone. '70 Nova 406"sb, 13.5-1, solid roller, Brodix, p.glide/t.brake, back halved, 9" Ford, spool 4.88, cage,ladder bar/coilover, 10.5 tire....... SOLD!! '67 C10 short/step side mount spare -- SOLD!! '72 Jimmy 2wd, 350/350, ps, pb, fun driver, lots of bondo & a shiny red paint job..... SOLD!! '69 Nova 350, 4spd, A/C, ps, p.b, ...SOLD!! |
|
|
|
|
07-24-2018, 05:02 PM
|
#4 |
|
Registered User
Join Date: Jul 2002
Location: St. James, MO
Posts: 1,238
|
Re: Master cylinder replace or paint?
Just remember that brake fluid is a dandy paint remover . . . .
__________________
'69 Longstep K-10: 327/SM465/T-221/Closed Knuckle Dana44/12-bolt. |
|
|
|
|
07-24-2018, 08:04 PM
|
#5 |
|
Moderator
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,204
|
Re: Master cylinder replace or paint?
Check out LMC link below for the Emission control decals you need...
http://www.lmctruck.com/icatalog/cb/full.aspx?Page=180 
|
|
|
|
|
07-24-2018, 10:21 PM
|
#6 |
|
Registered User
Join Date: Jul 2012
Location: Space Coast, Florida
Posts: 403
|
Re: Master cylinder replace or paint?
I don't like rusty master cylinders either, but I gave up on painting them because any brake fluid you get on it takes the paint right off.
__________________
1968 SWB Step Side, Big Block, 4L80E , Running! |
|
|
|
|
07-24-2018, 10:39 PM
|
#7 |
|
Senior Member
 
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,852
|
Re: Master cylinder replace or paint?
"Paint's" nice unless your master is sketchy anyway. This is mine with Eastwood's High Temperature Stainless Steel Coating. Works better on the master than exhaust manifolds.
|
|
|
|
|
07-24-2018, 10:41 PM
|
#8 |
|
Registered User
Join Date: Dec 2013
Location: Dunwoody,Ga
Posts: 443
|
Re: Master cylinder replace or paint?
Some of the rust restorer stuff turns the rusty outside to black. Since its not paint it hangs awhile - can't remember brand I used.
|
|
|
|
|
07-24-2018, 11:17 PM
|
#9 | |
|
Registered User
Join Date: Jun 2018
Location: Indianapolis IN
Posts: 114
|
Re: Master cylinder replace or paint?
Quote:
|
|
|
|
|
|
07-25-2018, 01:42 AM
|
#10 | |
|
Senior Member
Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,852
|
Re: Master cylinder replace or paint?
Quote:
|
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
