Aluminum diff covers - The 1947 - Present Chevrolet & GMC Truck Message Board Network

68panelman · 09-06-2018, 06:07 PM

Both trucks of mine leak a little from the rear diff covers and I'm wanting to get aftermarket finned aluminum. Sure I can't straighten out the old ones and apply copious amounts of silicone and be done with it, but not worth the effort.
My 70 Blazer is the easy no brainier, large capacity cover, but my 2wd 67 is in question with this type of finned cover, it seems to protrude further out then stock. My question is it seems the track bar would hit. I called suppliers and of course their staff can only read off a computer screen just as I am doing the same, given the same information I've already read, seems to be the norm nowadays?
Any suggestions as to types and brands?
Thanks, Mike

72LB · 09-06-2018, 06:19 PM

Most all require relocating the trac bar.

68panelman · 09-07-2018, 07:27 AM

Well ok, that sucks. The squeeze wouldn't be worth the juice to me

**special-K** · 09-07-2018, 07:37 AM

I agree. It's a close fit with all original set-up, so nothing deeper will work w/o other alterations

**biketopia** · 09-07-2018, 07:49 AM

The Moser aluminum girdle cover I have on my 71 fit's no problem.

68panelman · 09-07-2018, 07:55 AM

Can you post pictures when you get a chance?
I contemplated this type since it's flat where the bearing supports are, seemed like the only type that would work.

68panelman · 09-07-2018, 08:04 AM

OK, looking at the Moser on Summit, and read reviews and one guy had a 72 with it installed, the track bar looks to be in stock location?

71cadc10 · 09-07-2018, 09:55 AM

stock track bar with the Moser cover definitely fits, for 12 bolt apps.
aftermarket adjustable track bars, won't fit unless you get the type with the bend in them. I had a stock bar in my '71 with the Moser cover....then when I ordered the porterbuilt adjustable bar, I opted for the one with the 'z' bend in it that is made to clear the aftermarket covers.

**biketopia** · 09-07-2018, 10:26 AM

That's the exact cover I have, and yea I have stock rear suspension, for the moment. Good point on the aftermarket bars too!! I have my bed off my truck at the moment, I'll snap a picture this afternoon when I get home.

68panelman · 09-07-2018, 10:50 AM

Much appreciated to all the guys, thanks biketopia for the extra info.
Only complaint was some of the bolts were too long and had to be cut, did you also experience this biketopia?
Thanks, Mike

**biketopia** · 09-07-2018, 02:55 PM

I put mine on probably close to ten years ago. I don't remember having to though. I'll dig through some old pic of when I built it and see if I had any mention of it.

68panelman · 09-07-2018, 03:00 PM

Ok, cool

mike16 · 09-07-2018, 09:12 PM

so why are you replacing the cover? just because it was damaged. frankly I would just put another sheet metal on on there. everything else is expensive and over kill

72LB · 09-08-2018, 07:21 AM

I almost bought the Moser but was told if it's lowered it wouldn't work without relocating the trac bar.

68panelman · 09-08-2018, 09:39 AM

Quote:

Originally Posted by mike16

so why are you replacing the cover? just because it was damaged. frankly I would just put another sheet metal on on there. everything else is expensive and over kill

Replacements seem cheap and tinny, so while I'm at it, might as well upgrade. My late model truck has these Mag-hytec units, I like em'

**biketopia** · 09-13-2018, 01:46 PM

Sorry for the long delay, forgot I took the pictures!!

Name: 20180907_175719.jpg
Views: 258
Size: 51.3 KB

Name: 20180907_175702.jpg
Views: 285
Size: 53.6 KB

**Ironangel** · 09-13-2018, 02:04 PM

Quote:

Originally Posted by 72LB

I almost bought the Moser but was told if it's lowered it wouldn't work without relocating the trac bar.

Mine is lowered 4" in the rear so I did two things to get all kinds of clearance. First, I used a stack of SAE 5/8" washers to move the bar away as much as a full nut would allow, 4 or 5 washers. Secondly, I bent the bar up to clear the thick center portion of the cover. Bending the bar served two purposes on the lowered rear, it centers the rear end as well as clears the girdle cover...I'll dig some pics up...

**biketopia** · 09-13-2018, 02:13 PM

Name: 20180907_175711.jpg
Views: 257
Size: 56.9 KB

68panelman · 09-13-2018, 02:40 PM

Quote:

Originally Posted by biketopia

Sorry for the long delay, forgot I took the pictures!!

Attachment 1820459

Attachment 1820460

Thanks for the pics
Looks as if it would hit if compressed more than where it's at now

**biketopia** · 09-14-2018, 07:38 AM

Never had it hit, I used to load it down with a 4 wheeler and coolers and drive it like the 20 year old I was never had it hit.

68panelman · 09-14-2018, 08:39 AM

Great, thanks again for all your help.

GASoline71 · 09-14-2018, 10:06 AM

Quote:

Originally Posted by biketopia

The Moser aluminum girdle cover I have on my 71 fit's no problem.

I have the same cover on my 12 bolt in my 1972 C15. Lowered 4" in rear and the stock bar fits on mine with no interference as well.

Gary

68panelman · 09-14-2018, 11:18 AM

Thanks Gary for the extra assurance!

09-06-2018, 06:07 PM	#1
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Aluminum diff covers Both trucks of mine leak a little from the rear diff covers and I'm wanting to get aftermarket finned aluminum. Sure I can't straighten out the old ones and apply copious amounts of silicone and be done with it, but not worth the effort. My 70 Blazer is the easy no brainier, large capacity cover, but my 2wd 67 is in question with this type of finned cover, it seems to protrude further out then stock. My question is it seems the track bar would hit. I called suppliers and of course their staff can only read off a computer screen just as I am doing the same, given the same information I've already read, seems to be the norm nowadays? Any suggestions as to types and brands? Thanks, Mike

09-06-2018, 06:19 PM	#2
72LB Registered User Join Date: May 2017 Location: Inman/Boiling Springs, SC Posts: 420	Re: Aluminum diff covers Most all require relocating the trac bar. __________________ 1985 C10 shortbed, current project. Member of the Upstate SC GM Truck Club. Last edited by 72LB; 09-06-2018 at 06:53 PM.

09-07-2018, 07:27 AM	#3
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Well ok, that sucks. The squeeze wouldn't be worth the juice to me

09-07-2018, 07:37 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Aluminum diff covers I agree. It's a close fit with all original set-up, so nothing deeper will work w/o other alterations __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-07-2018, 07:49 AM	#5
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers The Moser aluminum girdle cover I have on my 71 fit's no problem. __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350

09-07-2018, 07:55 AM	#6
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Can you post pictures when you get a chance? I contemplated this type since it's flat where the bearing supports are, seemed like the only type that would work.

09-07-2018, 08:04 AM	#7
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers OK, looking at the Moser on Summit, and read reviews and one guy had a 72 with it installed, the track bar looks to be in stock location? Attached Images

09-07-2018, 09:55 AM	#8
71cadc10 Registered User Join Date: Apr 2004 Location: Boiling Springs, PA Posts: 435	Re: Aluminum diff covers stock track bar with the Moser cover definitely fits, for 12 bolt apps. aftermarket adjustable track bars, won't fit unless you get the type with the bend in them. I had a stock bar in my '71 with the Moser cover....then when I ordered the porterbuilt adjustable bar, I opted for the one with the 'z' bend in it that is made to clear the aftermarket covers. __________________ 71 C10 long bed, 2003 6.0L, 06GTO E40, T56, 12bolt 4.10 rear

09-07-2018, 10:26 AM	#9
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers That's the exact cover I have, and yea I have stock rear suspension, for the moment. Good point on the aftermarket bars too!! I have my bed off my truck at the moment, I'll snap a picture this afternoon when I get home. __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350

09-07-2018, 10:50 AM	#10
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Much appreciated to all the guys, thanks biketopia for the extra info. Only complaint was some of the bolts were too long and had to be cut, did you also experience this biketopia? Thanks, Mike

09-07-2018, 02:55 PM	#11
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers I put mine on probably close to ten years ago. I don't remember having to though. I'll dig through some old pic of when I built it and see if I had any mention of it. __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350

09-07-2018, 03:00 PM	#12
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Ok, cool

09-07-2018, 09:12 PM	#13
mike16 Registered User Join Date: Dec 2009 Location: bisbee, arizona Posts: 1,529	Re: Aluminum diff covers so why are you replacing the cover? just because it was damaged. frankly I would just put another sheet metal on on there. everything else is expensive and over kill

09-08-2018, 07:21 AM	#14
72LB Registered User Join Date: May 2017 Location: Inman/Boiling Springs, SC Posts: 420	Re: Aluminum diff covers I almost bought the Moser but was told if it's lowered it wouldn't work without relocating the trac bar. __________________ 1985 C10 shortbed, current project. Member of the Upstate SC GM Truck Club.

09-13-2018, 01:46 PM	#16
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers Sorry for the long delay, forgot I took the pictures!! __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350



Register or Log In To remove these advertisements.

09-13-2018, 02:13 PM	#18
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350

09-14-2018, 07:38 AM	#20
biketopia Senior Member Join Date: Jul 2015 Location: Warrenton VA Posts: 1,106	Re: Aluminum diff covers Never had it hit, I used to load it down with a 4 wheeler and coolers and drive it like the 20 year old I was never had it hit. __________________ 71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop. 07 Silverado Classic 2wd 95 Camaro 427SBC/TH350

09-14-2018, 08:39 AM	#21
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Great, thanks again for all your help.

09-14-2018, 11:18 AM	#23
68panelman Registered User Join Date: Jan 2011 Location: Delaware and Long Island, New York Posts: 3,456	Re: Aluminum diff covers Thanks Gary for the extra assurance!

Register or Log In To remove these advertisements.