89-77 front end swap???? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ooimpalaoo · 09-27-2018, 06:52 PM

I want to do a front end swap from my 89 suburban to a 76 front end....all I need is the fenders, radiator support,hood,grille, wiring, and I'm told the hinges are on the fenders so I'm guessing this is a fast swap. anything going to hold me back? from what I hear it's going from older to newer that has its messy parts.

Stormin08 · 09-28-2018, 12:19 AM

you would be better served one thread up. that year is covered on another board.

**special-K** · 09-28-2018, 06:54 AM

Thread meaning forum, the 73-87 or square body forum

**Palf70Step** · 09-28-2018, 07:56 AM

Moved it to the squarebody area for ya.

**mongocanfly** · 09-28-2018, 09:42 AM

Seems like there is a little difference in the cab where the hood and fender meet the door and windshield post...

**mongocanfly** · 09-28-2018, 09:46 AM

I found this on another site.....this guy did a writeup...

Ok, get ready cause this is a lot of info. First off, you dont have to cut anything, but you do have to change the ENTIRE NOSE!! I did this to my 86 K-20. I used the nose and motor of a 76 C-10. You have to use the hood hinges, the fenders, the radiator support, the inner fenders and the hood. You also have to adapt the windshield wipers and stuff, somehow. The hinges are connected to the inside of the regular fenders. You do however have to remove the cowl plate off of the 80's truck you are using. Heres what i did. I took the front off my 86 and the front off my 76. I put the radiator support on first then the outer fenders. I then had to use the 70s hinges for the hood too. I threw them on the fenders and put the hood on. No prob there. I used the 76 front bumper too and the front panel and grille. I also used the round headlights, obviously. That wire harness comes right out of the firewall, just make sure you remove the 3/8 bolt holding things together. I used my 76 wiper motor and trans, i just had to drill new holes for where the wiper arms connect to. Its actually pretty easy i think. You'll see, just make sure you have all the parts BEFORE YOU START!!! I also used the 350 from the 76. It bolts in nice, and the wireharness works too. It was quite a project, but it worked out well.

**mongocanfly** · 09-28-2018, 09:51 AM

And this.....https://www.gm***************/thread...und-eye.12882/

09-27-2018, 06:52 PM	#1
ooimpalaoo Registered User Join Date: Jul 2011 Location: Vernon BC Canada Posts: 287	89-77 front end swap???? I want to do a front end swap from my 89 suburban to a 76 front end....all I need is the fenders, radiator support,hood,grille, wiring, and I'm told the hinges are on the fenders so I'm guessing this is a fast swap. anything going to hold me back? from what I hear it's going from older to newer that has its messy parts.

09-28-2018, 12:19 AM	#2
Stormin08 Registered User Join Date: Sep 2018 Location: Moss Bluff, LA Posts: 381	Re: 89-77 front end swap???? you would be better served one thread up. that year is covered on another board.

09-28-2018, 06:54 AM	#3
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: 89-77 front end swap???? Thread meaning forum, the 73-87 or square body forum __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

09-28-2018, 07:56 AM	#4
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,216	Re: 89-77 front end swap???? Moved it to the squarebody area for ya. __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

09-28-2018, 09:42 AM	#5
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: 89-77 front end swap???? Seems like there is a little difference in the cab where the hood and fender meet the door and windshield post... Attached Images __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver Last edited by mongocanfly; 09-28-2018 at 09:53 AM.

09-28-2018, 09:46 AM	#6
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: 89-77 front end swap???? I found this on another site.....this guy did a writeup... Ok, get ready cause this is a lot of info. First off, you dont have to cut anything, but you do have to change the ENTIRE NOSE!! I did this to my 86 K-20. I used the nose and motor of a 76 C-10. You have to use the hood hinges, the fenders, the radiator support, the inner fenders and the hood. You also have to adapt the windshield wipers and stuff, somehow. The hinges are connected to the inside of the regular fenders. You do however have to remove the cowl plate off of the 80's truck you are using. Heres what i did. I took the front off my 86 and the front off my 76. I put the radiator support on first then the outer fenders. I then had to use the 70s hinges for the hood too. I threw them on the fenders and put the hood on. No prob there. I used the 76 front bumper too and the front panel and grille. I also used the round headlights, obviously. That wire harness comes right out of the firewall, just make sure you remove the 3/8 bolt holding things together. I used my 76 wiper motor and trans, i just had to drill new holes for where the wiper arms connect to. Its actually pretty easy i think. You'll see, just make sure you have all the parts BEFORE YOU START!!! I also used the 350 from the 76. It bolts in nice, and the wireharness works too. It was quite a project, but it worked out well. __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

09-28-2018, 09:51 AM	#7
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: 89-77 front end swap???? And this.....https://www.gm***************/thread...und-eye.12882/ __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.