67 chevy wipers - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Tenncman · 10-02-2018, 08:30 PM

First off hello everyone .Can someone help me figure out this gremlins. I turn my Wil e rd on low or high they won't work. But if I push on the sprayer button on the switch the wipers work but only for a few seconds. I can also control the speed of the wiper by pushing in the switch. But can't get them to work on the low or high setting.It h a s me scratching more than my head now.

Tenncman · 10-02-2018, 08:34 PM

Should say turn on my wipers on low or high they won't work. Sorry for the fat fingers

**LockDoc** · 10-02-2018, 09:41 PM

-
You are only getting a ground through the Dark Blue wire to the wiper. Is the wiper switch mounted in the dash? If so, with the ignition switch on turn the switch to the low position, reach up under the dash and wiggle the connector on the back of the wiper switch to see if you have a bad connection there. Try the high position also. If that doesn't do anything take a jumper wire with alligator clips on both ends and connect one end to bare metal on the wiper (not the screws) and the other end to bare metal on the cab and see what happens. Post back

Edit: Also make sure that the connectors on the wiper are connected like the picture below.

LockDoc
.

Tenncman · 10-02-2018, 09:47 PM

Lockdoc. The wiring looks the same as the picture. But what by connect one lead of the clip to the bare metal of wiper ? ( Do you mean the wiper arm ?)

**LockDoc** · 10-02-2018, 09:51 PM

Quote:

Originally Posted by Tenncman

Lockdoc. The wiring looks the same as the picture. But what by connect one lead of the clip to the bare metal of wiper ? ( Do you mean the wiper arm ?)

Nope, the wiper motor under the dash....

LockDoc

Tenncman · 10-02-2018, 09:54 PM

Ok. Thank you will give it a try . If it works,than onto the gas gauge .lol

**LockDoc** · 10-02-2018, 10:04 PM

Quote:

Originally Posted by Tenncman

Ok. Thank you will give it a try . If it works,than onto the gas gauge .lol

All the wire does is to make sure you are getting a ground. If one of those procedures makes them work you are still not done with them. You will have to fix them so they keep working......

LockDoc

Tenncman · 10-02-2018, 10:08 PM

So if I apply a good ground if the clips work. Would that take care of the issue found with the clips

**LockDoc** · 10-02-2018, 10:32 PM

Quote:

Originally Posted by Tenncman

So if I apply a good ground if the clips work. Would that take care of the issue found with the clips

Yes, if it was a permanent wire. There is a small brass strap on one of the mounting screws that is the actual ground but it is hard to see unless you pull the motor out.

I added a picture of the ground strap on the wiper motor mounting pad.

LockDoc

Tenncman · 10-02-2018, 11:50 PM

Ok. I just tried the jumper wire no change in condition. Reached hand up to back of switch wipers worked as long as I supplied lite pressure to the connector. Thinking I need to pull the switch and check both ends of the connector.

**LockDoc** · 10-03-2018, 11:40 AM

Quote:

Originally Posted by Tenncman

Ok. I just tried the jumper wire no change in condition. Reached hand up to back of switch wipers worked as long as I supplied lite pressure to the connector. Thinking I need to pull the switch and check both ends of the connector.

Yes, try cleaning the terminals and make sure the nut holding the switch in the dash is tight.

LockDoc

Tenncman · 10-03-2018, 02:20 PM

Found the issue with the wipers. Someone didn't put the retaining bezel nut on. Which cause a weak ground. Now onto the gas gauge.
Big thanks to Lock Doc

**LockDoc** · 10-03-2018, 03:56 PM

Quote:

Originally Posted by Tenncman

Found the issue with the wipers. Someone didn't put the retaining bezel nut on. Which cause a weak ground. Now onto the gas gauge.
Big thanks to Lock Doc

Good deal. Glad you got it fixed. Post up a new thread on the fuel gauge if you can't figure it out.....

LockDoc

Tenncman · 10-03-2018, 04:22 PM

Any ideas on where I can locate a bezel nit. The one the tightens the switch to the dash. Local hardware that usually has everything doesnt care it

**LockDoc** · 10-03-2018, 07:41 PM

Quote:

Originally Posted by Tenncman

Any ideas on where I can locate a bezel nit. The one the tightens the switch to the dash. Local hardware that usually has everything doesnt care it

PM me your mailing address and I will send you one.... You will need the "Star" washer too. To PM me click on my board name over on the left side then click on "send a private message to LockDoc"

LockDoc

Tenncman · 10-03-2018, 08:02 PM

PM sent. Thank you

**LockDoc** · 10-03-2018, 09:34 PM

Quote:

Originally Posted by Tenncman

PM sent. Thank you

No problem I will mail them out tomorrow.

LockDoc

**1971Stepside** · 10-03-2018, 10:01 PM

This is why I love this board

Tenncman · 10-03-2018, 10:04 PM

I agree with you 71 Stepside. Best site I have found by far.

**Getter-Done** · 10-03-2018, 10:17 PM

Quote:

Originally Posted by Tenncman

I agree with you 71 Stepside. Best site I have found by far.

Welcome
Yes this Site is (The Best)

10-02-2018, 08:30 PM	#1
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	67 chevy wipers First off hello everyone .Can someone help me figure out this gremlins. I turn my Wil e rd on low or high they won't work. But if I push on the sprayer button on the switch the wipers work but only for a few seconds. I can also control the speed of the wiper by pushing in the switch. But can't get them to work on the low or high setting.It h a s me scratching more than my head now.

10-02-2018, 08:34 PM	#2
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Should say turn on my wipers on low or high they won't work. Sorry for the fat fingers

10-02-2018, 09:41 PM	#3
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,415	Re: 67 chevy wipers - You are only getting a ground through the Dark Blue wire to the wiper. Is the wiper switch mounted in the dash? If so, with the ignition switch on turn the switch to the low position, reach up under the dash and wiggle the connector on the back of the wiper switch to see if you have a bad connection there. Try the high position also. If that doesn't do anything take a jumper wire with alligator clips on both ends and connect one end to bare metal on the wiper (not the screws) and the other end to bare metal on the cab and see what happens. Post back Edit: Also make sure that the connectors on the wiper are connected like the picture below. LockDoc . Attached Images __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - Last edited by LockDoc; 10-02-2018 at 09:48 PM.

10-02-2018, 09:47 PM	#4
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Lockdoc. The wiring looks the same as the picture. But what by connect one lead of the clip to the bare metal of wiper ? ( Do you mean the wiper arm ?)

10-02-2018, 09:54 PM	#6
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Ok. Thank you will give it a try . If it works,than onto the gas gauge .lol

10-02-2018, 10:08 PM	#8
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers So if I apply a good ground if the clips work. Would that take care of the issue found with the clips

10-02-2018, 11:50 PM	#10
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Ok. I just tried the jumper wire no change in condition. Reached hand up to back of switch wipers worked as long as I supplied lite pressure to the connector. Thinking I need to pull the switch and check both ends of the connector.

10-03-2018, 02:20 PM	#12
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Found the issue with the wipers. Someone didn't put the retaining bezel nut on. Which cause a weak ground. Now onto the gas gauge. Big thanks to Lock Doc Last edited by LockDoc; 10-03-2018 at 03:54 PM.

10-03-2018, 04:22 PM	#14
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers Any ideas on where I can locate a bezel nit. The one the tightens the switch to the dash. Local hardware that usually has everything doesnt care it

10-03-2018, 08:02 PM	#16
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers PM sent. Thank you

10-03-2018, 10:01 PM	#18
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,932	Re: 67 chevy wipers This is why I love this board __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."

10-03-2018, 10:04 PM	#19
Tenncman Registered User Join Date: Oct 2018 Location: Winchester Tennessee Posts: 21	Re: 67 chevy wipers I agree with you 71 Stepside. Best site I have found by far.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.