|
01-14-2019, 01:33 PM
|
#1 |
|
Senior Member
 
Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
rear sway bar info
Gents,
Any benefits to this with stock ride heights? or will this even work? 63-72 Rear Sway Bar 7/8" Coil Spring Trucks 1963-72 Rear 7/8" sway bar for 2 wheel drive coil spring equipped trucks. Includes all necessary mounting hardware. Some modifications are required to install if vehicle is stock height. https://gmcpauls.com/pictures/63-72rearcoilswaybar.jpg Curious about what modifications needs to work??
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks 
|
|
|
|
01-14-2019, 05:20 PM
|
#2 |
|
Moderator
  
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: rear sway bar info
Nothing more than drilling holes after you square the unit on your trailing arms. I think CPP and POL all make/sell them as well.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
|
|
|
|
01-14-2019, 08:18 PM
|
#3 | |
|
Registered User
Join Date: Jul 2017
Location: greenville
Posts: 88
|
Re: rear sway bar info
Quote:
|
|
|
|
|
|
01-15-2019, 10:21 AM
|
#4 |
|
Senior Member
Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: rear sway bar info
dose some one have a pic of it installed? I am curious where i have to drill holes??
I installed the solid rectangular tube trailing arms, not to keen on drilling into them
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks
|
|
|
|
|
01-15-2019, 12:00 PM
|
#5 |
|
Moderator
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: rear sway bar info
Installed:
http://67-72chevytrucks.com/vboard/s...7&postcount=36 POL web site - https://www.performanceonline.com/19...r-Coil-Spring/
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
|
|
|
|
01-17-2019, 12:22 PM
|
#6 |
|
Senior Member
Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: rear sway bar info
Thanks Master Chief ,
One more question did it come with dimensions or instructions on where to place and drill?
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks
|
|
|
|
|
01-17-2019, 02:23 PM
|
#7 |
|
Moderator
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: rear sway bar info
Yes it did.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
