![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jul 2014
Location: Washington
Posts: 532
|
Anyone Make Their Own Door Panels?
If So What Material Did You Use As Backing And How Did You Fasten Them To The Doors?
Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,720
|
Re: Anyone Make Their Own Door Panels?
I did in my Jimmy. I used 1/4" plywood, covered it with black vinyl. I used stainless sheetmetal screws and stainless trim washers and just screwed the 4 corners. I mounted 4" speakers in them and used 69-71 padded armrests.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
![]() |
![]() |
![]() |
#3 |
Registered User
![]() Join Date: Jan 2018
Location: Durham, North Carolina
Posts: 782
|
Re: Anyone Make Their Own Door Panels?
I used thick sheet metal and bead rolled a few "stripes" near the bottom and covered in vinyl (I used 3m spray glue and they came off so I need to get better glue). I am using those chrome trim screws (with the washer thing around the head) to install.
__________________
My Daily Driver Build: http://67-72chevytrucks.com/vboard/s...d.php?t=755668 |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jan 2018
Location: Durham, North Carolina
Posts: 782
|
Re: Anyone Make Their Own Door Panels?
Not to highjack but the PO may be interested in this as well, what glue did you use?
__________________
My Daily Driver Build: http://67-72chevytrucks.com/vboard/s...d.php?t=755668 |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2016
Location: Sugar Hill GA
Posts: 369
|
Re: Anyone Make Their Own Door Panels?
I had bad luck with that 3M stuff too. I now use marine grade contact cement. It will hold up to the heat inside the passenger compartment.
__________________
1967 C10 Step side 1970 AMX 390 1977 Datsun 280Z highly modified with '95 LT1 power |
![]() |
![]() |
![]() |
#6 |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
![]()
I went to my local shop and bought the board they use and cut the pattern out and then had them cover it for me. I did the dash pad and covered the 67 Chevelle wheel with same color leather.
There not perfect by no means but they cover up the 6x9 holes in the bottom of the doors and they are fastened like late model panels with the plastic tree's. ![]()
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 ![]() Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Anyone Make Their Own Door Panels?
A brand new set of steel door panels are only $55.00 from rock auto
https://www.rockauto.com/en/catalog/...oor+panel,1296 I've made several sets for members using their door panels or fabricating them from waterproof door board . If you have your original panels they can be wrapped with any color vinyl and reinstalled . ![]()
__________________
![]() 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop |
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Anyone Make Their Own Door Panels?
couple more
__________________
![]() 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,720
|
Re: Anyone Make Their Own Door Panels?
I don't think I even glued them. I stretched it around the back and through the speaker holes, door handle and regulator holes and stapled it on the back with 3/16 T50 staples.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
![]() |
![]() |
![]() |
Bookmarks |
|
|