Proper Rally Lug Nuts? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

2wdBlazer · 06-01-2004, 01:08 PM

Anyone know what the proper size and style of lug nut should be used? These are 5 lug Truck rally's.

crazy longhorn · 06-01-2004, 01:43 PM

they are 1/2" 20 thread, & the steel wheels have a 60 degree taper on the seat. I dont know if correct, or not but they look good....i got a set of acorn style chrome nuts at Advanced auto parts($28 for lugs & locks). crazyL

2wdBlazer · 06-02-2004, 04:32 PM

Anyone else? Just want to make sure I get the correct ones put my rally's on and not have to drive to the parts store 6 times. :p Wanna make sure they are closed end and will go all the way over the studs too. If someone had a pic too. That would be great.

crazy longhorn · 06-02-2004, 06:51 PM

As I remember, the studs were about 1 " long.....just be sure to have 1 1/8 - 1 1/4" depth inside the closed end lug nuts ,so you dont bottom out before tightening, & you should do fine. I didnt opt to run the lock nuts with the kit, so I picked up an extra 4 pack of nuts. they will be listed for steel wheels. crazyL

06-01-2004, 01:08 PM	#1
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Proper Rally Lug Nuts? Anyone know what the proper size and style of lug nut should be used? These are 5 lug Truck rally's. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

06-01-2004, 01:43 PM	#2
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	they are 1/2" 20 thread, & the steel wheels have a 60 degree taper on the seat. I dont know if correct, or not but they look good....i got a set of acorn style chrome nuts at Advanced auto parts($28 for lugs & locks). crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

06-02-2004, 04:32 PM	#3
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Anyone else? Just want to make sure I get the correct ones put my rally's on and not have to drive to the parts store 6 times. :p Wanna make sure they are closed end and will go all the way over the studs too. If someone had a pic too. That would be great. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

06-02-2004, 06:51 PM	#4
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	As I remember, the studs were about 1 " long.....just be sure to have 1 1/8 - 1 1/4" depth inside the closed end lug nuts ,so you dont bottom out before tightening, & you should do fine. I didnt opt to run the lock nuts with the kit, so I picked up an extra 4 pack of nuts. they will be listed for steel wheels. crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.