Help with partial vin and engine I.D. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SubarcticPig · 08-27-2019, 01:37 PM

Hello! I'll keep this short. I've been looking all around the internet and haven't been able to find my suffix code listed anywhere, or a partial vin set up like mine. The engine is in my truck and I haven't been able to find/see any casting numbers. So far I have deciphered St.Catherines, Ontario, Nov 11, and that is probably mid 70's and up because of the short fat pad, about an 1 3/4" wide. I need some help, bad!
K1111ULA
CG4122114

Thanks in advance!
SubarcticPig
1971 K20

cypressbog · 08-27-2019, 02:32 PM

The trucks never were numbers matching like the muscle cars.

**MJN** · 08-27-2019, 02:36 PM

Is it a small block or big block? Does the VIN stamping on the block match your truck's VIN? VIN stamping on truck engines didn't start until '73 I believe. The 350 in my '74 has the matching VIN stamped in the block. Block casting number is on the left rear of the block where the bellhousing bolts up. These can be hard to see with the engine in the truck and usually covered in a layer of oil and dirt.
Pictures help a ton, can you post a picture of the suffix code? Are you absolutely sure its ULA and not UJA or something similar?

**Mbeef61** · 08-27-2019, 02:41 PM

Block casting numbers are on the back of the block just below drivers side head near firewall.

Only thing I see with a ULA suffix is 1986 305.

Is it a v8? What side is oil dipstick on? Post pictures of the motor and numbers and try to find the casting #

SubarcticPig · 08-27-2019, 02:45 PM

It's a small block, and the numbers do not match to the truck. I was pokin around under there and couldn't find the castings, maybe a higher power light and cleaner would help me along. I will attempt to include a photo, but the stampings are pretty clear.

SubarcticPig · 08-27-2019, 02:48 PM

It seems like it would be out of a van?

SubarcticPig · 08-27-2019, 03:04 PM

I just can't get any visual on the castings on the firewall side, I'm going to borrow a mirror on a stick and to see if that helps! There are castings on both lower sides of the block, I don't know if that would help. I'm assuming the 305 casting, which is on the driver's side, indicates that it is in fact a 305? I do not know what the other castings are, Which are on the passenger side.

geezer#99 · 08-27-2019, 04:04 PM

There’s pics in here where to look and info on the numbers you find.

https://www.mortec.com/

BigBird05 · 08-27-2019, 11:01 PM

Nov 11, 305 1986 c-10,c-20,k-10.

geezer#99 · 08-27-2019, 11:06 PM

Quote:

Originally Posted by BigBird05

Nov 11, 305 1986 c-10,c-20,k-10.

What’s your source?

BigBird05 · 08-28-2019, 07:24 AM

Just typed it into my search engine.

**MJN** · 08-28-2019, 09:03 AM

I found the ULA suffix code at this link- its a pdf file.

1986 305, 150hp, 4BBL, Manual Trans, Truck engine

https://www.corvetteforum.com/forums...ook_2018-1.pdf

**71CHEVYSHORTBED402** · 08-28-2019, 02:15 PM

There wasn't a VIN on old blocks. Not that I'm aware of anyway.

Between the part number, date codes and other items concerning the truck (e.g. SPID, build sheet etc.), you can determine whether or not your long block is "numbers matching".

Codes off my BBC = "numbers matching".

SubarcticPig · 09-07-2019, 01:38 AM

Thank you everyone for your replies! MJN and BigBird coming through with a solid win. Funny story that truck got stolen, but I had some luck on my side. My starter was on it's way out the door and was only engaging the motor for a second tops, hard to start. Which is part of the reason for searching for the year and size. My roommate heard them f in around, chased them in his boxers but they got it in gear and got away. Called me up and I ran to the hood, then 4 of us started searching the neighborhood. The same roommate stumbled upon them parked, blocked them in, and got out with a machete and the rage of a thousand dissapointed gods. Scared the piss out of em as they were about to shoot up, they ran away leaving the drugs and all in the truck. Imagine telling the person who bought it off the showroom in 71 that story! I came out with my truck, no damage, a broken phillips, a broken flathead, and a vise grip! Lucky me.

I've been very busy. I apologize for the wall of text and lack of response. Thanks again for the help and I hope to do more than lurk.

If you want to check out what I've been busy with, look up flugtag in St.Paul. We just got done building a glider, the team name is Her Smoke Rose Up Forever. I'm the pilot and we will be flying about 1:15 ish Minnesota time.

Truck shenanigans soon,
SubarcticPig

08-27-2019, 01:37 PM	#1
SubarcticPig Registered User Join Date: Sep 2017 Location: Minneapolis, Minnesota Posts: 5	Help with partial vin and engine I.D. Hello! I'll keep this short. I've been looking all around the internet and haven't been able to find my suffix code listed anywhere, or a partial vin set up like mine. The engine is in my truck and I haven't been able to find/see any casting numbers. So far I have deciphered St.Catherines, Ontario, Nov 11, and that is probably mid 70's and up because of the short fat pad, about an 1 3/4" wide. I need some help, bad! K1111ULA CG4122114 Thanks in advance! SubarcticPig 1971 K20

08-27-2019, 02:32 PM	#2
cypressbog Go Pack Go! Join Date: Nov 2005 Location: Green Bay Posts: 2,669	Re: Help with partial vin and engine I.D. The trucks never were numbers matching like the muscle cars.

08-27-2019, 02:36 PM	#3
MJN Registered User Join Date: Feb 2000 Location: Maquoketa, Ia/ Orr, Mn Posts: 3,032	Re: Help with partial vin and engine I.D. Is it a small block or big block? Does the VIN stamping on the block match your truck's VIN? VIN stamping on truck engines didn't start until '73 I believe. The 350 in my '74 has the matching VIN stamped in the block. Block casting number is on the left rear of the block where the bellhousing bolts up. These can be hard to see with the engine in the truck and usually covered in a layer of oil and dirt. Pictures help a ton, can you post a picture of the suffix code? Are you absolutely sure its ULA and not UJA or something similar? __________________ '51 South Bend Model "9A" '56 Chevy 3600 NAPCO '74 Chevy Cheyenne Super K20-restored on 37's '72 GMC Sierra Custom K2500- in progress '08 GMC Envoy Denali '12 GMC Sierra 2500HD Denali '17 GMC Yukon XL VCCA member #58596 http://www.nohrco.com

08-27-2019, 02:41 PM	#4
Mbeef61 Senior Member Join Date: Jun 2009 Location: Portland - OR Posts: 243	Re: Help with partial vin and engine I.D. Block casting numbers are on the back of the block just below drivers side head near firewall. Only thing I see with a ULA suffix is 1986 305. Is it a v8? What side is oil dipstick on? Post pictures of the motor and numbers and try to find the casting #

08-27-2019, 02:45 PM	#5
SubarcticPig Registered User Join Date: Sep 2017 Location: Minneapolis, Minnesota Posts: 5	Re: Help with partial vin and engine I.D. It's a small block, and the numbers do not match to the truck. I was pokin around under there and couldn't find the castings, maybe a higher power light and cleaner would help me along. I will attempt to include a photo, but the stampings are pretty clear. Attached Images

08-27-2019, 02:48 PM	#6
SubarcticPig Registered User Join Date: Sep 2017 Location: Minneapolis, Minnesota Posts: 5	Re: Help with partial vin and engine I.D. It seems like it would be out of a van? Attached Images

08-27-2019, 03:04 PM	#7
SubarcticPig Registered User Join Date: Sep 2017 Location: Minneapolis, Minnesota Posts: 5	Re: Help with partial vin and engine I.D. I just can't get any visual on the castings on the firewall side, I'm going to borrow a mirror on a stick and to see if that helps! There are castings on both lower sides of the block, I don't know if that would help. I'm assuming the 305 casting, which is on the driver's side, indicates that it is in fact a 305? I do not know what the other castings are, Which are on the passenger side. Attached Images

08-27-2019, 04:04 PM	#8
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,668	Re: Help with partial vin and engine I.D. There’s pics in here where to look and info on the numbers you find. https://www.mortec.com/

08-27-2019, 11:01 PM	#9
BigBird05 Registered User Join Date: Aug 2019 Location: Cheraw Posts: 1,305	Re: Help with partial vin and engine I.D. Nov 11, 305 1986 c-10,c-20,k-10.

08-28-2019, 07:24 AM	#11
BigBird05 Registered User Join Date: Aug 2019 Location: Cheraw Posts: 1,305	Re: Help with partial vin and engine I.D. Just typed it into my search engine.

08-28-2019, 09:03 AM	#12
MJN Registered User Join Date: Feb 2000 Location: Maquoketa, Ia/ Orr, Mn Posts: 3,032	Re: Help with partial vin and engine I.D. I found the ULA suffix code at this link- its a pdf file. 1986 305, 150hp, 4BBL, Manual Trans, Truck engine https://www.corvetteforum.com/forums...ook_2018-1.pdf __________________ '51 South Bend Model "9A" '56 Chevy 3600 NAPCO '74 Chevy Cheyenne Super K20-restored on 37's '72 GMC Sierra Custom K2500- in progress '08 GMC Envoy Denali '12 GMC Sierra 2500HD Denali '17 GMC Yukon XL VCCA member #58596 http://www.nohrco.com

08-28-2019, 02:15 PM	#13
71CHEVYSHORTBED402 Senior Member Join Date: Feb 2009 Location: Northern Nevada Posts: 7,274	Re: Help with partial vin and engine I.D. There wasn't a VIN on old blocks. Not that I'm aware of anyway. Between the part number, date codes and other items concerning the truck (e.g. SPID, build sheet etc.), you can determine whether or not your long block is "numbers matching". Codes off my BBC = "numbers matching". Attached Images __________________ Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025

09-07-2019, 01:38 AM	#14
SubarcticPig Registered User Join Date: Sep 2017 Location: Minneapolis, Minnesota Posts: 5	Re: Help with partial vin and engine I.D. Thank you everyone for your replies! MJN and BigBird coming through with a solid win. Funny story that truck got stolen, but I had some luck on my side. My starter was on it's way out the door and was only engaging the motor for a second tops, hard to start. Which is part of the reason for searching for the year and size. My roommate heard them f in around, chased them in his boxers but they got it in gear and got away. Called me up and I ran to the hood, then 4 of us started searching the neighborhood. The same roommate stumbled upon them parked, blocked them in, and got out with a machete and the rage of a thousand dissapointed gods. Scared the piss out of em as they were about to shoot up, they ran away leaving the drugs and all in the truck. Imagine telling the person who bought it off the showroom in 71 that story! I came out with my truck, no damage, a broken phillips, a broken flathead, and a vise grip! Lucky me. I've been very busy. I apologize for the wall of text and lack of response. Thanks again for the help and I hope to do more than lurk. If you want to check out what I've been busy with, look up flugtag in St.Paul. We just got done building a glider, the team name is Her Smoke Rose Up Forever. I'm the pilot and we will be flying about 1:15 ish Minnesota time. Truck shenanigans soon, SubarcticPig



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.