LS Swap Motor mount question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

19Loki67 · 09-02-2019, 11:41 AM

I built a LS3 with a 416 stroker kit for my 67 c10. I have adapter plates from dirty dingo to mount to the block. what I am looking for is stronger perches that mount to my frame to accommodate the extra power. (a lot extra) I found the tubular mounts from performance online, which are the ones I really like, but it appeared the frame where the top mounts is narrower than mine. is there a tubular mount that i'm not seeing for the 67 thicker frame?

siggyfreud · 09-02-2019, 01:16 PM

I'm not really sure what you're asking/describing when you say thicker frame. Do you have photos?

19Loki67 · 09-02-2019, 03:53 PM

I would if I knew how to post pics on here I would

this is the link to the mounts Im talking about

http://www.performanceonline.com/196...-Brackets-V-8/

if u notice at the top of the mount in the pic where its installed the top of frame rail is thinner than the bottom. mine doesn't narrow like that

**clay68c10** · 09-02-2019, 04:08 PM

Trim your frame rail, the later trucks came that way for the BBC. Or so I’ve heard.

19Loki67 · 09-02-2019, 06:39 PM

I’m definitely considering that
Posted via Mobile Device

19Loki67 · 09-02-2019, 06:42 PM

Quote:

Originally Posted by 19Loki67

I’m definitely considering that
Posted via Mobile Device

Posted via Mobile Device

**Captainfab** · 09-02-2019, 11:32 PM

Just trim the top flange of your frame similar to that pic you posted and you will be good.

19Loki67 · 09-12-2019, 07:59 AM

So I got my mounts in. The Andrés were longer than in the pic. No trimming needed. I guess maybe they make one for a 67 and they just don’t have a pic of it on the site
Posted via Mobile Device

19Loki67 · 09-12-2019, 08:00 AM

Mounts* not andres
Posted via Mobile Device

**The Rocknrod** · 09-12-2019, 08:18 AM

When I purchased mine I had the same question. Luckily I dropped by POL store in Corona and they said they trimmed the top frame rail. Now you would think that would be information they would impart on a buyer or potential buyer and I mentioned that. They are nice though. I fit the engine into the frame and body before it went to paint. I do like them.

19Loki67 · 09-12-2019, 10:18 AM

When I got them in my hand I was pleased. The weight of them feels like a sturdy product. And the powder coat on them seems to be good quality as well. Hopefully the fitment is as good as they look and feel
Posted via Mobile Device

09-02-2019, 11:41 AM	#1
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	LS Swap Motor mount question I built a LS3 with a 416 stroker kit for my 67 c10. I have adapter plates from dirty dingo to mount to the block. what I am looking for is stronger perches that mount to my frame to accommodate the extra power. (a lot extra) I found the tubular mounts from performance online, which are the ones I really like, but it appeared the frame where the top mounts is narrower than mine. is there a tubular mount that i'm not seeing for the 67 thicker frame? Last edited by 19Loki67; 09-02-2019 at 11:47 AM.

09-02-2019, 01:16 PM	#2
siggyfreud Registered User Join Date: Jun 2012 Location: Portland Posts: 1,330	Re: LS Swap Motor mount question I'm not really sure what you're asking/describing when you say thicker frame. Do you have photos? __________________ Current Build - Project "Ghost of Poseidon" 72 C10 Pro-touring build Previous Build - 66 GMC Pro-touring build. Sold.

09-02-2019, 03:53 PM	#3
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	Re: LS Swap Motor mount question I would if I knew how to post pics on here I would this is the link to the mounts Im talking about http://www.performanceonline.com/196...-Brackets-V-8/ if u notice at the top of the mount in the pic where its installed the top of frame rail is thinner than the bottom. mine doesn't narrow like that

09-02-2019, 04:08 PM	#4
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,905	Re: LS Swap Motor mount question Trim your frame rail, the later trucks came that way for the BBC. Or so I’ve heard. __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

09-02-2019, 06:39 PM	#5
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	Re: LS Swap Motor mount question I’m definitely considering that Posted via Mobile Device

09-02-2019, 11:32 PM	#7
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,246	Re: LS Swap Motor mount question Just trim the top flange of your frame similar to that pic you posted and you will be good. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

09-12-2019, 07:59 AM	#8
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	Re: LS Swap Motor mount question So I got my mounts in. The Andrés were longer than in the pic. No trimming needed. I guess maybe they make one for a 67 and they just don’t have a pic of it on the site Posted via Mobile Device

09-12-2019, 08:00 AM	#9
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	Re: LS Swap Motor mount question Mounts* not andres Posted via Mobile Device

09-12-2019, 08:18 AM	#10
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: LS Swap Motor mount question When I purchased mine I had the same question. Luckily I dropped by POL store in Corona and they said they trimmed the top frame rail. Now you would think that would be information they would impart on a buyer or potential buyer and I mentioned that. They are nice though. I fit the engine into the frame and body before it went to paint. I do like them. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

09-12-2019, 10:18 AM	#11
19Loki67 Registered User Join Date: Nov 2018 Location: Corpus Christi Tx Posts: 23	Re: LS Swap Motor mount question When I got them in my hand I was pleased. The weight of them feels like a sturdy product. And the powder coat on them seems to be good quality as well. Hopefully the fitment is as good as they look and feel Posted via Mobile Device



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.