6 rib p/s pump pulley - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Yobyllib · 10-08-2019, 06:54 PM

I am looking for a single 6 rib serpentine belt pulley with a 5/8" shaft with a keyway slot. I bought ones years ago and am now finally installing my motor and I managed to damage the pulley beyond repair. I do not want to have to purchase a whole a kit again nor so I want to spend the money on a March pulley. I am not having any luck. Any leads any where?
Thanks

Yobyllib · 10-09-2019, 03:50 PM

I guess I am the only person out there that is using this type of pulley system, I will find my own solution without the help of this board.

**jaros44sr** · 10-09-2019, 08:19 PM

well, I suppose, if someone had a answer to your problem they would have posted up. My only answer was to buy a March pulley or check out a junk yard. But, you disted the March idea, so that is why I didn't post up

**MDPotter** · 10-10-2019, 12:07 PM

You'll probably get a better response if you post in the 67-72 forum, not the build forum and have a little patience. Also, you can try using the search function. Not everyone gets on here every day even every few days.

10-08-2019, 06:54 PM	#1
Yobyllib Registered User Join Date: Jul 2011 Location: Victoria, BC Canada Posts: 26	6 rib p/s pump pulley I am looking for a single 6 rib serpentine belt pulley with a 5/8" shaft with a keyway slot. I bought ones years ago and am now finally installing my motor and I managed to damage the pulley beyond repair. I do not want to have to purchase a whole a kit again nor so I want to spend the money on a March pulley. I am not having any luck. Any leads any where? Thanks

10-09-2019, 03:50 PM	#2
Yobyllib Registered User Join Date: Jul 2011 Location: Victoria, BC Canada Posts: 26	Re: 6 rib p/s pump pulley I guess I am the only person out there that is using this type of pulley system, I will find my own solution without the help of this board.

10-09-2019, 08:19 PM	#3
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,766	Re: 6 rib p/s pump pulley well, I suppose, if someone had a answer to your problem they would have posted up. My only answer was to buy a March pulley or check out a junk yard. But, you disted the March idea, so that is why I didn't post up __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

10-10-2019, 12:07 PM	#4
MDPotter Senior Member Join Date: Aug 2018 Location: Western Colorado Posts: 1,165	Re: 6 rib p/s pump pulley You'll probably get a better response if you post in the 67-72 forum, not the build forum and have a little patience. Also, you can try using the search function. Not everyone gets on here every day even every few days. __________________ 1964 Chevy C10 - Gen IV 5.3 Restomod http://67-72chevytrucks.com/vboard/s...d.php?t=768632 1968 GMC C15 - Gen III 6.0 Restomod http://67-72chevytrucks.com/vboard/s...d.php?t=772047 1969 Chevy C10 - Restoration http://67-72chevytrucks.com/vboard/s...d.php?t=809184 1978 Chevy Scottsdale K20 1993 Chevy C1500 - 5.3/T56 swapped 2008 Silverado Duramax



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.