47-55.1 Tuck In Front Bumper - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Driver_WT · 11-22-2019, 08:50 AM

What is the best way to tuck in the front bumper on my 53 Chevy 3100? Do I modify the splash pan or make a new one? I have already trimmed three inches off of each end of the front bumper, now I want it tucked in more.

Any pics of a nicely tucked front bumper?

thanks.

Wade

**mongocanfly** · 11-22-2019, 09:37 AM

Just modify what you have or make a new one....just like your already thinking

Driver_WT · 11-22-2019, 10:12 AM

Thanks. Do most people just tuck the front bumper in to the front of the bottom of the grill, or do you go under the grill?

**mongocanfly** · 11-22-2019, 05:41 PM

Personal choice I guess...I'd keep it under the grill bar, but a little in front of it

**mr48chev** · 11-22-2019, 06:41 PM

Quote:

Originally Posted by mongocanfly

Personal choice I guess...I'd keep it under the grill bar, but a little in front of it

Which I interpret as on the same level that it is originally but closer to the grill.

On the splash apron, I'd say that may depend on your personal skills or the skills available to you. Either cutting and welding or fabbing a new one. I don't think you will gain what you hope to by cutting and welding though and a newly fabricated one could slip below the grill as long as it cleared a tad.

I have to do pretty much the same thing with the 49 Plymouth ribbed bumpers that I am putting on mine. Right down to trimming the ends for clearance.

Driver_WT · 11-22-2019, 11:02 PM

Quote:

Originally Posted by mr48chev

Which I interpret as on the same level that it is originally but closer to the grill.

On the splash apron, I'd say that may depend on your personal skills or the skills available to you. Either cutting and welding or fabbing a new one. I don't think you will gain what you hope to by cutting and welding though and a newly fabricated one could slip below the grill as long as it cleared a tad.

I have to do pretty much the same thing with the 49 Plymouth ribbed bumpers that I am putting on mine. Right down to trimming the ends for clearance.

Thank you. I do have a new splash pan, but if I cut it up, I would like it to work. Just looking for some ideas, advice and pics of what others have done to increase my own probability of success. A good friend is helping with the truck project and he is a great welder with good equipment.

**oldman3** · 11-23-2019, 12:36 AM

I ended up cutting about 3" out of my bumper brackets (see Pic 1)

I also narrowed mine about 3" per side and welded studs to the bumper and smoothed them out (see pic 2 @3)

I made mine own splash apron to fit my bumper and then the fenders, etc.

Here's the finished product (see pic 4)

Hope this helps...Jim

Driver_WT · 11-23-2019, 12:49 AM

Thanks very much Jim. I have reviewed your build a number of times and have copied some things, including your trimmed and smoothed front bumper. Is your front splash pan just flat sheet metal?

Wade

**oldman3** · 11-23-2019, 10:39 AM

Quote:

Originally Posted by Driver_WT

Is your front splash pan just flat sheet metal?

Wade

Wade, thanks for checking out the build. Yes, splash pan in 1/8" flat sheet metal. I made a poster board template of the shape and size, then cut it out...Jim

**oldman3** · 11-23-2019, 10:42 AM

Wade, forgot to add that I welded four tabs on the pan to hold in place, like the orginal one. Here's a pic...Jim

Driver_WT · 11-23-2019, 10:49 AM

Thanks Jim. I appreciate the detail and the pics.

Wade

my56chevytruck · 11-23-2019, 10:54 PM

Quote:

Originally Posted by Driver_WT

What is the best way to tuck in the front bumper on my 53 Chevy 3100? Do I modify the splash pan or make a new one? I have already trimmed three inches off of each end of the front bumper, now I want it tucked in more.

Any pics of a nicely tucked front bumper?

thanks.

Wade

any thoughts of cutting the width down on the bumper to begin with? Making it not as wide as they are??

Driver_WT · 11-23-2019, 10:58 PM

Quote:

Originally Posted by my56chevytruck

any thoughts of cutting the width down on the bumper to begin with? Making it not as wide as they are??

I have cut 3" off each end (copied from Oldman3 - Jim).

I could not make the bumper any narrower as I have put two 3.5" driving lights in the front bumper.

**oldman3** · 11-24-2019, 12:36 AM

Quote:

Originally Posted by Driver_WT

I could not make the bumper any narrower as I have put two 3.5" driving lights in the front bumper.

Always thought that would look good, if everything was shaped right, look forward to seeing this...Jim

Driver_WT · 11-24-2019, 09:43 AM

Quote:

Originally Posted by oldman3

Always thought that would look good, if everything was shaped right, look forward to seeing this...Jim

I will post up some pics soon Jim.

**Dan in Pasadena** · 11-26-2019, 04:52 PM

Quote:

Originally Posted by oldman3

I ended up cutting about 3" out of my bumper brackets (see Pic 1)

I also narrowed mine about 3" per side and welded studs to the bumper and smoothed them out (see pic 2 @3)

I made mine own splash apron to fit my bumper and then the fenders, etc.

Here's the finished product (see pic 4)

Hope this helps...Jim

Jim, I’d never noticed before but in the photo it looks like the bumper & splash pan are welded together and smoothed out to be one piece. Your fit must be spot on. Nice!

Too bad the Task Force trucks never came with a splash pan. I considered making some for mine but in the crush at the end I never went back to it. This thread has me thinking!

**mr48chev** · 11-26-2019, 05:22 PM

I'd just say that Oldman3 has that fit and finish thing down to the gnats patootie and raised the bar a couple of notches there. What looks like seamless is superior fit. Time and patience there rather than throwing money at it.

**oldman3** · 11-26-2019, 08:18 PM

Quote:

Originally Posted by Dan in Pasadena

Jim, I’d never noticed before but in the photo it looks like the bumper & splash pan are welded together and smoothed out to be one piece. Your fit must be spot on. Nice!

Too bad the Task Force trucks never came with a splash pan. I considered making some for mine but in the crush at the end I never went back to it. This thread has me thinking!

Quote:

Originally Posted by mr48chev

I'd just say that Oldman3 has that fit and finish thing down to the gnats patootie and raised the bar a couple of notches there. What looks like seamless is superior fit. Time and patience there rather than throwing money at it.

Thanks Dan and mr48, for the high praise. There is a small gap between bumper and splash apron, just enough to keep it from hitting each other. Dan I'm sure you can cut a pattern of what you want, put it to metal and finish. You have a beautiful truck and this addition would add to it...Jim

Driver_WT · 11-27-2019, 09:00 AM

Quote:

Originally Posted by oldman3

Thanks Dan and mr48, for the high praise. There is a small gap between bumper and splash apron, just enough to keep it from hitting each other. Dan I'm sure you can cut a pattern of what you want, put it to metal and finish. You have a beautiful truck and this addition would add to it...Jim

I thought it was welded as well. Very nice work Jim. I am hoping that my project will be at least 75% of what you have done.

**oldman3** · 11-27-2019, 10:27 AM

Quote:

Originally Posted by Driver_WT

I thought it was welded as well. Very nice work Jim. I am hoping that my project will be at least 75% of what you have done.

Thanks Wade. I thought about welding it together, but getting it to line up with top of bumper and under grill I wasn't sure would work, so no welding. I'm sure yours will come out fine, looking forward to pics...Jim

MD2020 · 11-27-2019, 10:33 AM

A little off topic
Mine's a 1956 truck
I did not have a front bumper and it had a Nova front clip.
I bought a black bumper off of eba__ and cut about 6" out of the center and pushed it up against the lower grill panel, then made some bracket to hold it.

Fit's like it was suppose to be that way.

11-22-2019, 08:50 AM	#1
Driver_WT Registered User Join Date: Dec 2017 Location: River John, NS Posts: 448	Tuck In Front Bumper What is the best way to tuck in the front bumper on my 53 Chevy 3100? Do I modify the splash pan or make a new one? I have already trimmed three inches off of each end of the front bumper, now I want it tucked in more. Any pics of a nicely tucked front bumper? thanks. Wade __________________ 53 Chevy 3100, SBC 355, 700R4, S10 frame, Ford 8.8 rear with 4.11 gears, front disc & rear drum brakes Last edited by Driver_WT; 11-22-2019 at 10:27 AM.

11-22-2019, 09:37 AM	#2
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: Tuck In Front Bumper Just modify what you have or make a new one....just like your already thinking __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

11-22-2019, 10:12 AM	#3
Driver_WT Registered User Join Date: Dec 2017 Location: River John, NS Posts: 448	Re: Tuck In Front Bumper Thanks. Do most people just tuck the front bumper in to the front of the bottom of the grill, or do you go under the grill? __________________ 53 Chevy 3100, SBC 355, 700R4, S10 frame, Ford 8.8 rear with 4.11 gears, front disc & rear drum brakes

11-22-2019, 05:41 PM	#4
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: Tuck In Front Bumper Personal choice I guess...I'd keep it under the grill bar, but a little in front of it __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

11-23-2019, 12:36 AM	#7
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: Tuck In Front Bumper I ended up cutting about 3" out of my bumper brackets (see Pic 1) I also narrowed mine about 3" per side and welded studs to the bumper and smoothed them out (see pic 2 @3) I made mine own splash apron to fit my bumper and then the fenders, etc. Here's the finished product (see pic 4) Hope this helps...Jim Attached Images __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

11-23-2019, 12:49 AM	#8
Driver_WT Registered User Join Date: Dec 2017 Location: River John, NS Posts: 448	Re: Tuck In Front Bumper Thanks very much Jim. I have reviewed your build a number of times and have copied some things, including your trimmed and smoothed front bumper. Is your front splash pan just flat sheet metal? Wade __________________ 53 Chevy 3100, SBC 355, 700R4, S10 frame, Ford 8.8 rear with 4.11 gears, front disc & rear drum brakes

11-23-2019, 10:42 AM	#10
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,559	Re: Tuck In Front Bumper Wade, forgot to add that I welded four tabs on the pan to hold in place, like the orginal one. Here's a pic...Jim Attached Images __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br />

11-23-2019, 10:49 AM	#11
Driver_WT Registered User Join Date: Dec 2017 Location: River John, NS Posts: 448	Re: Tuck In Front Bumper Thanks Jim. I appreciate the detail and the pics. Wade __________________ 53 Chevy 3100, SBC 355, 700R4, S10 frame, Ford 8.8 rear with 4.11 gears, front disc & rear drum brakes

11-26-2019, 05:22 PM	#17
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,705	Re: Tuck In Front Bumper I'd just say that Oldman3 has that fit and finish thing down to the gnats patootie and raised the bar a couple of notches there. What looks like seamless is superior fit. Time and patience there rather than throwing money at it. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

11-27-2019, 10:33 AM	#21
MD2020 Registered User Join Date: Sep 2018 Location: Batesville,MISSISSIPPI Posts: 312	Re: Tuck In Front Bumper A little off topic Mine's a 1956 truck I did not have a front bumper and it had a Nova front clip. I bought a black bumper off of eba__ and cut about 6" out of the center and pushed it up against the lower grill panel, then made some bracket to hold it. Fit's like it was suppose to be that way.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.