|
02-01-2020, 02:26 AM
|
#1 |
|
Registered User
 Join Date: Jan 2018
Location: Northern CA
Posts: 588
|
Cup Holder
Had to make something for a cup holder, as there just isn't too much available out there.
This is in my Jimmy, but would work for a column shift truck too. Test fitting prior to carpet install. Pat |
|
|
|
02-01-2020, 02:46 AM
|
#2 |
|
Registered User
Join Date: Jan 2011
Location: Glendale, AZ
Posts: 3,178
|
Re: Cup Holder
Pretty cool idea, I don’t think I have seen that before. How is it when you reach for the drink? Are you going to bolt it in place?
|
|
|
|
|
02-01-2020, 09:31 AM
|
#3 | |
|
Registered User
Join Date: Jan 2018
Location: Northern CA
Posts: 588
|
Re: Cup Holder
Quote:
It's not too bad at all when reaching for a drink. Obviously not as nice as it would be if in a console, but definitely doable. After dynamat and carpeting, I intend to secure (bolt) it into place. I would hate to have an accident and have that piece of iron become a projectile inside the cab. Pat |
|
|
|
|
|
02-01-2020, 11:06 AM
|
#4 |
|
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
Re: Cup Holder
Nice. I used a old S 10 shifter and cup holder in my 71 C 10. I cut the front/back on the console off so it would fit.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
|
|
|
02-01-2020, 06:06 PM
|
#5 |
|
Registered User
Join Date: Jun 2015
Location: Carlos MN
Posts: 2,017
|
Re: Cup Holder
I did something similar using two pieces of exhaust tubing welded to a flat plate with a small extension with a hole drilled in it so I could slip it under the trim ring of the shifter and hole it in place with one of the trim screws.
|
|
|
|
|
02-02-2020, 04:30 PM
|
#6 |
|
Registered User
Join Date: Nov 2011
Location: sherwood park ,alberta
Posts: 44
|
Re: Cup Holder
well it has cup holders and more
works great and fits great |
|
|
|
|
02-03-2020, 09:04 AM
|
#7 |
|
Senior Member
 
Join Date: Dec 1999
Location: TX
Posts: 1,559
|
Re: Cup Holder
That's a Lincoln Navigator or Ford Expedition console.
|
|
|
|
|
02-03-2020, 04:43 PM
|
#8 | |
|
Registered User
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
|
Re: Cup Holder
Quote:
__________________
72 C10 lwb fleetside -stock 350/350 combo |
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
