Need measurements for rocker replacement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

82sdale · 02-04-2020, 09:08 PM

getting ready to replace rockers. read a lot but cant find any solid measurements. looking for a measurement from some reliable fixed point down to where the top of the rocker should be to ensure the door is going to have room for alignment. anything else that would be useful is appreciated

stangtjk · 02-08-2020, 03:55 PM

http://67-72chevytrucks.com/vboard/s...d.php?t=741445

Check out the 5th post of this thread.

**raggedjim** · 02-10-2020, 11:22 AM

I didn't measure anything when I did mine. I did take the door and fender off, and then back on, and then off, and then back on, over and over again until I felt sure everything was going to align.

Good luck, Rg

**jaros44sr** · 02-10-2020, 01:22 PM

x3^^^^

Huskerboy2 · 02-11-2020, 10:09 PM

Just my $.02, but I wouldn't fit that rocker without having the door and fender on. Like mentioned above, that might mean taking them off and on more than once.

hemi43 · 02-13-2020, 09:57 AM

Like others have said, a measurement is useless. Use the door as your alignment jig because at the end, it's what matters. Besides, no two trucks are identical. Back in 1970 some of the tolerances were +-1/4".

02-04-2020, 09:08 PM	#1
82sdale Registered User Join Date: Aug 2016 Location: houston tx Posts: 17	Need measurements for rocker replacement getting ready to replace rockers. read a lot but cant find any solid measurements. looking for a measurement from some reliable fixed point down to where the top of the rocker should be to ensure the door is going to have room for alignment. anything else that would be useful is appreciated

02-08-2020, 03:55 PM	#2
stangtjk Registered User Join Date: Nov 2016 Location: Newport News Posts: 249	Re: Need measurements for rocker replacement http://67-72chevytrucks.com/vboard/s...d.php?t=741445 Check out the 5th post of this thread.

02-10-2020, 11:22 AM	#3
raggedjim Senior Member Join Date: Jun 2002 Location: Murray, Kentucky Posts: 3,496	Re: Need measurements for rocker replacement I didn't measure anything when I did mine. I did take the door and fender off, and then back on, and then off, and then back on, over and over again until I felt sure everything was going to align. Good luck, Rg __________________ Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 Ideas - https://67-72chevytrucks.com/vboard/...d.php?t=851743

02-10-2020, 01:22 PM	#4
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,766	Re: Need measurements for rocker replacement x3^^^^ __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

02-11-2020, 10:09 PM	#5
Huskerboy2 Senior Member Join Date: Feb 2001 Location: Austin, Texas, USA Posts: 1,628	Re: Need measurements for rocker replacement Just my $.02, but I wouldn't fit that rocker without having the door and fender on. Like mentioned above, that might mean taking them off and on more than once. __________________ '72 Chevy Blazer

02-13-2020, 09:57 AM	#6
hemi43 Registered User Join Date: Mar 2015 Location: Ontario Canada Posts: 1,526	Re: Need measurements for rocker replacement Like others have said, a measurement is useless. Use the door as your alignment jig because at the end, it's what matters. Besides, no two trucks are identical. Back in 1970 some of the tolerances were +-1/4".



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.