|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-25-2020, 07:08 PM
|
#1 |
|
Registered User
Join Date: Mar 2013
Location: Waco, Texas
Posts: 411
|
1966 Chevy Truck rear end
Any advice on this, looks like water got in the rear.
See photos. |
|
|
|
04-25-2020, 10:04 PM
|
#2 |
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,246
|
Re: 1966 Chevy Truck rear end
I would wire brush the gears the best you can, and then rinse it all out with either brake cleaner or carb cleaner. Then a new gasket and fresh 75W90 gear oil and drive it a hundred or so miles, see how it sounds and then change the oil again.
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
|
04-25-2020, 11:34 PM
|
#3 |
|
Registered User
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 2,220
|
Re: 1966 Chevy Truck rear end
Same.
Old Chevy's can run like crap without even knowing it, for a very long time. If it's reasonably quiet, you dodged a bullet; run with it. If it's death incarnate, well, it was buggered anyway. You won't be making "already-buggered" any worse by driving it.
__________________
1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate |
|
|
|
|
04-26-2020, 10:04 AM
|
#4 |
|
Registered User
Join Date: Feb 2013
Location: central California
Posts: 2,733
|
Re: 1966 Chevy Truck rear end
That happened to me once too. It was doomed. Here's the thread I started. http://67-72chevytrucks.com/vboard/s...d.php?t=782519
|
|
|
|
|
04-26-2020, 11:36 AM
|
#5 |
|
Registered User
Join Date: Mar 2013
Location: Waco, Texas
Posts: 411
|
Re: 1966 Chevy Truck rear end
Thanks guys that will be the plan.
|
|
|
|
|
04-26-2020, 05:38 PM
|
#6 | |
|
Registered User
Join Date: Jun 2010
Location: gadsden, alabama
Posts: 468
|
Re: 1966 Chevy Truck rear end
Quote:
__________________
Due to financial constraints, the light at the end of the tunnel will be shut off until further notice |
|
|
|
|
|
04-26-2020, 06:32 PM
|
#7 |
|
Registered User
Join Date: Mar 2013
Location: Waco, Texas
Posts: 411
|
Re: 1966 Chevy Truck rear end
Got the axles out but somehow the pinion gear got turned and both spider gears of feel out.
Any trick to getting those back in. |
|
|
|
|
04-26-2020, 07:48 PM
|
#8 |
|
Registered User
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 2,220
|
Re: 1966 Chevy Truck rear end
Put them in the openings on either side, then turn the axles/side-gears to "walk" them in.
__________________
1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, boosted-LS 1977 Silverado: Shortboxed & dropped, potato-potato V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag Lotus Super 7 Replica: Scratch-built street-legal rollerskate |
|
|
|
|
04-29-2020, 03:10 PM
|
#9 |
|
Registered User
Join Date: Jan 2019
Location: Bonner Springs, KS
Posts: 56
|
Re: 1966 Chevy Truck rear end
Hold the gears in line with their thrust washer on the case. Get both in and slowly turn the case till you can get the pin back in
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
