UT $1.00 60-63 C10 Cab Cuts - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67see10 · 05-03-2020, 10:11 PM

Quote:

Originally Posted by DPowers

Ill take this section right here please. Shipping to 37843. Let me know how you want paid.

Here’s a picture of the cut

67see10 · 05-03-2020, 10:15 PM

Quote:

Originally Posted by darkhorse970

I’d like to have one side of the dash, for the “hump” portion on top.

Which one would you like?

67see10 · 05-03-2020, 10:16 PM

Quote:

Originally Posted by lownslw64

Can i get this section cut out please? let me know how much to 94513. Thanks

Here’s a picture of the cut

lownslw64 · 05-03-2020, 10:45 PM

Quote:

Originally Posted by 67see10

Here’s a picture of the cut

perfect. let me know how much to 94513 and what is your paypal. thanks!

darkhorse970 · 05-04-2020, 06:38 AM

Quote:

Originally Posted by 67see10

Which one would you like?

I will take the glove box side. If the glove box door is available I’d like to have it too. Thanks!

67see10 · 05-04-2020, 03:48 PM

Quote:

Originally Posted by cwcarpenter98

That's ok. If the rust isn't completely through on either side, I need both of these circled sections. I have not cut into my truck yet to see the extent of the rust, but I know it looks pretty bad from the outside, especially on the passenger side. Just to be on the safe side, if you are willing to cut out the inside section with it, that would be great. I don't need the roof skin though. Seam sealer deteriorated and let water rust out the upper lip areas.

My zip is 30188

Thanks!

*Edit* I will go check on my cab in a couple minutes to see if I need the inside part or not.

Pictures

**DPowers** · 05-04-2020, 06:02 PM

Quote:

Originally Posted by 67see10

Here’s a picture of the cut

Great
Let me know how much and how you want paid.

darkhorse970 · 05-08-2020, 10:51 AM

Quote:

Originally Posted by darkhorse970

I will take the glove box side. If the glove box door is available I’d like to have it too. Thanks!

Let me know how much I owe you, I appreciate it!

GranPanteraRoja · 05-12-2020, 01:41 PM

Hi,

I would like to following section on the driver's side corner around the gas tank filler shipped to 30032. Please let me know how you would like payment.

Thank you!

**cwcarpenter98** · 05-16-2020, 11:39 PM

Got my pieces yesterday. Just what I needed, thanks!

Ennehazrad · 05-25-2020, 10:57 PM

Was wondering first if you could provide a cut from the passenger side corner and if so, how much for the part + shipping? The attached pic will give you the details but if you need anymore info please let me know.
Posted via Mobile Device

Ennehazrad · 05-25-2020, 11:02 PM

Was wondering first if you could provide a cut from the passenger side corner and if so, how much for the part + shipping? The attached pic will give you the details but if you need anymore info please let me know.
Posted via Mobile Device

Brad54 · 05-26-2020, 04:09 PM

If it's still there, I'd like to get the area along the bottom edge of the back of the cab, the pinch weld that goes from the cab corner, up over the frame, from the driver side to the passenger side.

05-12-2020, 01:41 PM	#34
GranPanteraRoja Registered User Join Date: Mar 2019 Location: ATL, GA Posts: 55	Re: $1.00 60-63 C10 Cab Cuts Hi, I would like to following section on the driver's side corner around the gas tank filler shipped to 30032. Please let me know how you would like payment. Thank you!

05-16-2020, 11:39 PM	#35
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,491	Re: $1.00 60-63 C10 Cab Cuts Got my pieces yesterday. Just what I needed, thanks! __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

05-25-2020, 10:57 PM	#36
Ennehazrad Registered User Join Date: Apr 2015 Location: Riverside, California Posts: 70	Was wondering first if you could provide a cut from the passenger side corner and if so, how much for the part + shipping? The attached pic will give you the details but if you need anymore info please let me know. Posted via Mobile Device Attached Images

05-25-2020, 11:02 PM	#37
Ennehazrad Registered User Join Date: Apr 2015 Location: Riverside, California Posts: 70	Was wondering first if you could provide a cut from the passenger side corner and if so, how much for the part + shipping? The attached pic will give you the details but if you need anymore info please let me know. Posted via Mobile Device Attached Images

05-26-2020, 04:09 PM	#38
Brad54 Registered User Join Date: Aug 2006 Location: Athens, Georgia Posts: 1,458	Re: $1.00 60-63 C10 Cab Cuts If it's still there, I'd like to get the area along the bottom edge of the back of the cab, the pinch weld that goes from the cab corner, up over the frame, from the driver side to the passenger side. __________________ '61 Suburban daily driver: off the road due to 180-pound 8-pt buck! '62 K-10 long-step project '61 C30 Camper, aka "Valdez" There's no cool like Old School



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.