1960 Apache C10 Transmission Mount - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**60short** · 06-16-2020, 12:52 AM

Does anybody know off the top of their head what size the bolts are that hold the transmission mounts to the crossmembers, or know if anybody sells these bellhousing mounts?

I am apparently missing the bolt and nut / washer on the passenger side - and the mount looks pretty beat too...

THnaks!

**cwcarpenter98** · 06-16-2020, 09:32 AM

Does your mount look kinda like mine? I'm not sure exactly what the 60 mount looks like. If it looks the same, I can go put a socket on my bolt to check the size

AcampoDave · 06-16-2020, 09:42 AM

That mount is an "Anchor 2107"

**60short** · 06-16-2020, 10:06 AM

passenger side - missing

Untitled by Keith, on Flickr

drivers side - not sure if that ones right, but at least its there

Untitled by Keith, on Flickr

**cwcarpenter98** · 06-16-2020, 12:19 PM

Those are the same mounts as on my 63. I can roll underneath and check the bolt size for you later today. You might also be missing the rubber piece that goes on the bottom side of the crossmember

AcampoDave · 06-16-2020, 10:35 PM

The one underneath is "Anchor 2108"

**60short** · 06-16-2020, 11:02 PM

Quote:

Originally Posted by cwcarpenter98

Does your mount look kinda like mine? I'm not sure exactly what the 60 mount looks like. If it looks the same, I can go put a socket on my bolt to check the size

Quote:

Originally Posted by cwcarpenter98

Those are the same mounts as on my 63. I can roll underneath and check the bolt size for you later today. You might also be missing the rubber piece that goes on the bottom side of the crossmember

Thanks for the offer Christian!

Quote:

Originally Posted by AcampoDave

The one underneath is "Anchor 2108"

Quote:

Originally Posted by AcampoDave

That mount is an "Anchor 2107"

It sounds like Dave has this one nailed ... I just need to get a grade 8 bolt thats will fit through there, and use both mounts?

you two guys are the best!

**cwcarpenter98** · 06-17-2020, 07:31 PM

Sorry, I forgot to check the size yesterday.

The bolt goes through both mounts from the bottom up to the bell housing.
The bolt is a 3/4". I know it is coarse thread, but I didn't pull the bolt out to check the length. With the rubber part inside the crossmember, the bolt head is close to being flush with the bottom of the crossmember

**Captainfab** · 06-17-2020, 09:58 PM

The bolts are 1/2"-13 X 3-1/2". Bolts are not designated by the size of the hex.

**60short** · 06-17-2020, 11:32 PM

Quote:

Originally Posted by cwcarpenter98

Sorry, I forgot to check the size yesterday.

The bolt goes through both mounts from the bottom up to the bell housing.
The bolt is a 3/4". I know it is coarse thread, but I didn't pull the bolt out to check the length. With the rubber part inside the crossmember, the bolt head is close to being flush with the bottom of the crossmember

Quote:

Originally Posted by Captainfab

The bolts are 1/2"-13 X 3-1/2". Bolts are not designated by the size of the hex.

Thanks guys!

I will try and get one rounded up tomorrow, for the weekend.

You are both greatly appreciated

06-16-2020, 12:52 AM	#1
60short Revitalizing a 6T C10 Join Date: Aug 2017 Location: Santa Barbara, CA Posts: 222	1960 Apache C10 Transmission Mount Does anybody know off the top of their head what size the bolts are that hold the transmission mounts to the crossmembers, or know if anybody sells these bellhousing mounts? I am apparently missing the bolt and nut / washer on the passenger side - and the mount looks pretty beat too... THnaks!

06-16-2020, 09:32 AM	#2
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,488	Re: 1960 Apache C10 Transmission Mount Does your mount look kinda like mine? I'm not sure exactly what the 60 mount looks like. If it looks the same, I can go put a socket on my bolt to check the size Attached Images __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

06-16-2020, 09:42 AM	#3
AcampoDave Registered User Join Date: Feb 2013 Location: central California Posts: 2,774	Re: 1960 Apache C10 Transmission Mount That mount is an "Anchor 2107"

06-16-2020, 10:06 AM	#4
60short Revitalizing a 6T C10 Join Date: Aug 2017 Location: Santa Barbara, CA Posts: 222	Re: 1960 Apache C10 Transmission Mount passenger side - missing Untitled by Keith, on Flickr drivers side - not sure if that ones right, but at least its there Untitled by Keith, on Flickr

06-16-2020, 12:19 PM	#5
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,488	Re: 1960 Apache C10 Transmission Mount Those are the same mounts as on my 63. I can roll underneath and check the bolt size for you later today. You might also be missing the rubber piece that goes on the bottom side of the crossmember __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

06-16-2020, 10:35 PM	#6
AcampoDave Registered User Join Date: Feb 2013 Location: central California Posts: 2,774	Re: 1960 Apache C10 Transmission Mount The one underneath is "Anchor 2108"

06-17-2020, 07:31 PM	#8
cwcarpenter98 Senior Member Join Date: Jan 2018 Location: Hickory Flat, GA Posts: 4,488	Re: 1960 Apache C10 Transmission Mount Sorry, I forgot to check the size yesterday. The bolt goes through both mounts from the bottom up to the bell housing. The bolt is a 3/4". I know it is coarse thread, but I didn't pull the bolt out to check the length. With the rubber part inside the crossmember, the bolt head is close to being flush with the bottom of the crossmember __________________ Christian Carpenter 1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive Overdrive wiring here 1963-ish truck bed trailer - Half-Wit 1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed 1995 Dodge Dakota Sport "I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson

06-17-2020, 09:58 PM	#9
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: 1960 Apache C10 Transmission Mount The bolts are 1/2"-13 X 3-1/2". Bolts are not designated by the size of the hex. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.