5.3 C10 Swap Idle Issue

[shortboxin]

Thanks for the reply!

Originally Posted by skyphix

What PCM are you using and has it been tuned/modified at all?

The PCM is from a 2002 Chevy Tahoe with DBC. I don't know specifics as to model number if that's what your asking. It has been modified, but pretty much only to remove anti-theft and rear O2s. I had wondered if the guy that tweaked it may have made a mistake?

Originally Posted by skyphix

There is a TORX screw below the TB but you also have to do a TPS reset. If you didn't change that during the swap, its probably more related to build up than adjustment. Clearly I have more experience with DBW.

Everything stayed stock.

Originally Posted by skyphix

Another stupid question is, did you verify that all of the spark plug wires are firmly snapped into the coil packs? Two clicks total for factory wires.

I can double check this, but I'm pretty confident on this.

Originally Posted by skyphix

Do you have a check engine light or OBD2 reader that you could scan for any codes?

No CEL on the truck yet, but no codes in the scanner. Sorry, should've mentioned this up front.

Originally Posted by skyphix

I am finding a ton of info on dirty DBC Throttle bodies causing the throttle blades to stick. Idle speed between 500-600 is very normal, but below that isn't. Have you tried using brake cleaner to clean out any gunk in and around the throttle blade, including pushing it open with your finger and cleaning any residue around the blade and hinge areas?

I have not done anything more than a quick clean. Thing is that it never feels like it's sticking when I press the gas. Additionally, the truck sounds like it's on the verge of stalling when it's at 550-600RPM.

[skyphix]

Originally Posted by shortboxin

Thanks for the reply!

The PCM is from a 2002 Chevy Tahoe with DBC. I don't know specifics as to model number if that's what your asking. It has been modified, but pretty much only to remove anti-theft and rear O2s. I had wondered if the guy that tweaked it may have made a mistake?


Everything stayed stock.



I can double check this, but I'm pretty confident on this.


No CEL on the truck yet, but no codes in the scanner. Sorry, should've mentioned this up front.


I have not done anything more than a quick clean. Thing is that it never feels like it's sticking when I press the gas. Additionally, the truck sounds like it's on the verge of stalling when it's at 550-600RPM.

Its a little weird that it sounds on the verge of stalling at that RPM with a totally stock engine. Does it ever high idle when its cold? Or does it keep trying to find low idle?

Have you checked your fuel pressure at all? Whats the fuel system setup?

I'd give the TB a more thorough cleaning. Not all I found felt sticking - but they all seemed to benefit from a good cleaning. Both of the 5.3's I have here are DBW so I dont have a DBC throttle body here to look at.


Removing VATs and the rear O2's (disabling secondary O2 bank) really shouldn't cause this issue - even without O2's hooked up it should idle (mine did, just really rough.)

Do you have any exhaust leaks BEFORE the O2 sensors? What is the exhaust setup? Its hard to tell from the video but it does sound like theres quite a bit of exhaust leak. Might just be the video.

What is your intake tract setup? Are there any modifications to the engine? Specifically, cam?

In this video, this is my truck at "cold" idle (air temp was around 80) - around 750-800rpm.
https://www.youtube.com/watch?v=kUoSWj7fvXo


At the beginning of this video, you can hear what hot idle is, fluctuating a bit between 525 and 550. I still need to do some fine tuning to this tune (this is a 6.0 tune thats been adjusted for my displacement and injectors, done by PSI, but I'll be picking up HPTuners and fine tuning it.)

https://www.youtube.com/watch?v=nWyB34SdS9U


Yours sounds like its running rough through the whole RPM range that was in the video you posted... I know you checked for vacuum leaks, but if the cam it stock, it does sound like a vacuum leak. All the ports are plugged off on the TOP of the intake, correct?

[shortboxin]

Originally Posted by skyphix

Its a little weird that it sounds on the verge of stalling at that RPM with a totally stock engine. Does it ever high idle when its cold? Or does it keep trying to find low idle?

As for wanting to stall, if it's at 550RPM, it's okay except it will drop lower to the 350-400RPM range and then stall from there. If driving, then coming to a stop or slowing for a turn, it may just stall under the additional load. When you say cold, I will assume you mean engine cold. To that, I don't believe it ever high idles at all.

I should probably also mention that I assume it is a stock cam. I bought the engine used with 125K and just put new gaskets, seals, and externals like sensors and water pump on it.

Originally Posted by skyphix

Have you checked your fuel pressure at all? Whats the fuel system setup?

I have not checked fuel pressure. I have a hard time believing that the pressure could be low enough to cause an idle problem, yet accelerate with no issues. I stomp on it and it responds very well. Am I wrong in that assumption?

Running a stock pickup and tank from an 87 R10 and using a 96-97 Chevy P/U pump.

Originally Posted by skyphix

I'd give the TB a more thorough cleaning. Not all I found felt sticking - but they all seemed to benefit from a good cleaning.

Will do.

Originally Posted by skyphix

Removing VATs and the rear O2's (disabling secondary O2 bank) really shouldn't cause this issue - even without O2's hooked up it should idle (mine did, just really rough.)

This is what he was supposed to do. I'm not 100% sure that's what was done... he asked a number of things, all answers below. He's been doing these for years, so I anticipate that he's just got files he downloads quickly and that's it. Maybe he did the wrong one?

PCM Part #12200411
Drive by cable TB
5.3 from 2004 Silverado (based on dished piston)
2532_ _ _ _ fuel injectors (VIN Z)
2002 return style fuel rail
Case grounded O2s

Originally Posted by skyphix

Do you have any exhaust leaks BEFORE the O2 sensors? What is the exhaust setup? Its hard to tell from the video but it does sound like theres quite a bit of exhaust leak. Might just be the video.

I can get better video maybe Sunday from outside the truck so it'll be easier to hear. I'm running S10 swap shorty headers with true dual exhaust, no crossover pipe, with side exit. I'm not running cats and I have Flowmaster "glass packs". In my opinion, I don't think I have any exhaust leaks, but I had to drill out 5 of the header bolts and one of them had some minor thread damage, so I didn't want to torque it a lot for fear of stripping it out.

Originally Posted by skyphix

What is your intake tract setup? Are there any modifications to the engine? Specifically, cam?

Intake and throttle body is stock 2002 Tahoe. As far as I know, the engine was stock. I bought it used from a friend of the guy that owned the truck (he went to prison). As for cam, I can't be 100% sure.

Originally Posted by skyphix

Yours sounds like its running rough through the whole RPM range that was in the video you posted... I know you checked for vacuum leaks, but if the cam it stock, it does sound like a vacuum leak. All the ports are plugged off on the TOP of the intake, correct?

In my opinion, I don't believe I'm having any issues with how the engine runs under acceleration or even at a steady speed. As for ports on the intake, the only ones I'm aware of are the port for the fuel pressure regulator, the port in back for the power brake booster and then the evap canister purge valve, which I'm still running.

[skyphix]

Originally Posted by shortboxin

As for wanting to stall, if it's at 550RPM, it's okay except it will drop lower to the 350-400RPM range and then stall from there. If driving, then coming to a stop or slowing for a turn, it may just stall under the additional load. When you say cold, I will assume you mean engine cold. To that, I don't believe it ever high idles at all.

I should probably also mention that I assume it is a stock cam. I bought the engine used with 125K and just put new gaskets, seals, and externals like sensors and water pump on it.


I have not checked fuel pressure. I have a hard time believing that the pressure could be low enough to cause an idle problem, yet accelerate with no issues. I stomp on it and it responds very well. Am I wrong in that assumption?

Running a stock pickup and tank from an 87 R10 and using a 96-97 Chevy P/U pump.

Will do.

This is what he was supposed to do. I'm not 100% sure that's what was done... he asked a number of things, all answers below. He's been doing these for years, so I anticipate that he's just got files he downloads quickly and that's it. Maybe he did the wrong one?

PCM Part #12200411
Drive by cable TB
5.3 from 2004 Silverado (based on dished piston)
2532_ _ _ _ fuel injectors (VIN Z)
2002 return style fuel rail
Case grounded O2s

I can get better video maybe Sunday from outside the truck so it'll be easier to hear. I'm running S10 swap shorty headers with true dual exhaust, no crossover pipe, with side exit. I'm not running cats and I have Flowmaster "glass packs". In my opinion, I don't think I have any exhaust leaks, but I had to drill out 5 of the header bolts and one of them had some minor thread damage, so I didn't want to torque it a lot for fear of stripping it out.

Intake and throttle body is stock 2002 Tahoe. As far as I know, the engine was stock. I bought it used from a friend of the guy that owned the truck (he went to prison). As for cam, I can't be 100% sure.

In my opinion, I don't believe I'm having any issues with how the engine runs under acceleration or even at a steady speed. As for ports on the intake, the only ones I'm aware of are the port for the fuel pressure regulator, the port in back for the power brake booster and then the evap canister purge valve, which I'm still running.

So, the PCM is from the same Z code vehicle right? Z code means flex fuel injectors which I assume you probably already know, and are different than the normal 24lb injectors in the non flex vehicles. If the injector parameters are off, it would cause this issue.

I agree though on checking fuel pressure. I’m running the same tank/pickup/EP381 pump, with a corvette fuel regulator/filter and -6an lines.

I do mean cold engine temp - you can hear the difference in my two videos between cold idle and hot idle. Cold idle is the revving video, hot idle is the driving video. My exhaust IS leaky (I need to reweld a couple of spots) but all leaks are after the o2s and it runs great.) Open and closed circuit fueling within the PCM is what I’m really referencing at a technical level.


EVAP purge at the front of the intake is what I was most concerned about. I blocked mine off. And the big brake booster 3/8 barbed fitting was the one that got me - totally forgot to plug that and it did what you describe.

Me saying it sounds leaky or like it’s running rough, could just be your video. It’s hard to tell without standing right in front of it. The exhaust manifolds only call for 13-15 lbs so should be ok there.

My suggestion would be fuel pressure (could even be too high if you’re not running a return system and don’t have any regulator online,) clean the throttle body thoroughly. If neither of those address it, a conversation with the tuner to verify your injector settings are correct.

[Mattchu60]

I didnt read all the replies, but I recently did a 5.3 swap into my C10. The first 6-7 times I drove it, it would stall the engine whenever I shifted into D, or R.

Now it seems to have "learned" how to idle higher over time and the stalling issue has gone away. I did not change anything. It could be that it just needs some time to figure things out?

[skyphix]

Originally Posted by Mattchu60

I didnt read all the replies, but I recently did a 5.3 swap into my C10. The first 6-7 times I drove it, it would stall the engine whenever I shifted into D, or R.

Now it seems to have "learned" how to idle higher over time and the stalling issue has gone away. I did not change anything. It could be that it just needs some time to figure things out?

You bring up a good point - what transmission?

[shortboxin]

Originally Posted by skyphix

You bring up a good point - what transmission?

Missed this question... I am running a 4L60E. The Tahoe was running a 4L60E originally as well.

[shortboxin]

Originally Posted by Mattchu60

I didnt read all the replies, but I recently did a 5.3 swap into my C10. The first 6-7 times I drove it, it would stall the engine whenever I shifted into D, or R.

Now it seems to have "learned" how to idle higher over time and the stalling issue has gone away. I did not change anything. It could be that it just needs some time to figure things out?

I was hoping for this originally, but I've driven it 1500 miles or so. The battery's been disconnected many times in between, but I've done 4-5 drive cycles up to as much as 130 miles on 2 of them and no change. Wish I was so lucky.

[shortboxin]

UPDATE: I contacted the tuner and he got back to me very quickly this time. I asked some additional questions which I added the second response as well.

1st response:
"Yes I just opened your file from June 2019 and everything matches below, injectors, rail, throttle, o2’s. Pretty much all stock air/fuel programming with changes needed for swap, security, emissions, so on, fans on… I use pre-configured files for most of my programming, files I’ve used on many swaps prior and know are good working combinations. The file for your PCM was one of these pre-configured that I may have only had to adjust one or two things to have it ready to your specs. This cuts out possibilities of mistakes on the many settings I do for a swap programming."

2nd response:
"It won’t throw codes for evap emissions, rear o2s, cats. So all sensors remaining, will run diagnostic tests as normal, coil controls, inj, temp, maf, air intake temp , so on, all will run as normal. P0300 misfire diagnostics for some reason do not work in swaps. I think the PCM want’s to see a fuel level to let them run (pcm ignores misfires if fuel level below 10%)."

[shortboxin]

First off, I want to say thank you so much for all of the feedback skyphix! I really appreciate it a lot.

Originally Posted by skyphix

So, the PCM is from the same Z code vehicle right? Z code means flex fuel injectors which I assume you probably already know, and are different than the normal 24lb injectors in the non flex vehicles. If the injector parameters are off, it would cause this issue.

It is the Z code PCM and the injectors are from the same vehicle, yes. I am unsure of what parameters this guy used since I mailed it to him and there was zero communication from him. Not even a note as to whether or not he got the specs from me.

Originally Posted by skyphix

EVAP purge at the front of the intake is what I was most concerned about. I blocked mine off. And the big brake booster 3/8 barbed fitting was the one that got me - totally forgot to plug that and it did what you describe.

I'm running my HVAC controls in the cab off of a tee in this line, but the issue has been there since day one before I tapped into this hose on Monday.

Originally Posted by skyphix

My suggestion would be fuel pressure (could even be too high if you’re not running a return system and don’t have any regulator online,) clean the throttle body thoroughly. If neither of those address it, a conversation with the tuner to verify your injector settings are correct.

Running the factory vacuum controlled regulator on this thing. It's unlikely that I'll be able to get any communication with the tuner as he just doesn't respond to anything. Sadly, I'll probably have to get another PCM and get it programmed by someone else to see if that's it.