|
02-17-2021, 11:28 PM
|
#1 |
|
Registered User
Join Date: Apr 2018
Location: Columbia,Tn
Posts: 28
|
Eaton HO swap
I have a 1971 C 20 with the Eaton rear end.Transmission is 4 speed.I would like to take the Eaton out and replace it with something with a higher gear ratio.Just wondering what axle swaps others have done.TIA.
Last edited by Bobbysgmc; 02-18-2021 at 10:19 AM. Reason: trailing arms with coil suspension |
|
|
|
02-17-2021, 11:38 PM
|
#2 |
|
Registered User
Join Date: Sep 2018
Location: Reno
Posts: 58
|
Re: Eaton HO swap
A lot of people go the dana 60 or gm 14 bolt route. You could also put a 12 bolt 1/2 ton or ford 9" if you wanted to. Personally, I am thinking about the 14 bolt route in my '72 k20. I really like the old eaton, but mine is an open diff and I would like a locker.
|
|
|
|
|
02-18-2021, 01:27 AM
|
#3 |
|
The Older Generation
   
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,771
|
Re: Eaton HO swap
-
I am in the process of getting a Dana 60 3.54 rear ready to install in my '68 C-20. I am installing the new brakes on it at this time. Do you have rear leaf springs or coils? LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
02-18-2021, 02:08 AM
|
#4 |
|
Senior Member
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,628
|
Re: Eaton HO swap
I would recommend a 14 bolt, better parts availability as far as the brakes go. (Dana 60 drum parts are beginning to get tough to find). Stronger diff than the 60. A little more work to make it fit. Available ratios: 3.42--3.73--4.10--4.56--4.88--5.13--5.38. 3.21s IF you can find a good set.
|
|
|
|
|
02-19-2021, 11:40 AM
|
#5 |
|
Proprietor of Dale's Corner
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,245
|
Re: Eaton HO swap
I just swapped my Eaton out. I replaced it with a dana 60.
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul |
|
|
|
|
02-19-2021, 12:06 PM
|
#6 |
|
All about them K’s
 
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,487
|
Re: Eaton HO swap
I’m a big fan of the original eaton and the 14 bolt. Both are very strong. The 14 bolt is what I would go to if you swap to something else. One thing I would do is swap to the 01+ 2 piece hub seals, they are a much better design than the originals.
__________________
Tyler '57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888 '72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879 ‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206 '98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s |
|
|
|
|
02-20-2021, 10:41 AM
|
#7 |
|
Registered User
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,727
|
Re: Eaton HO swap
Like other things, it depends on your skill set and tools. If it is a coil spring truck and you can't fab brackets and mounts, the Dana 60 is the choice. 3.54 gears were common in big block trucks and would be 15% less gear than the 4.10 eaton and 30% less than 4.56. If you have one that has higher numeric gears for a donor, 3.30 aftermarket gears are available.
If you have a leaf spring truck it is easier but still nothing bolts in. The 14 bolt is the easiest donor to find if you can fab the mounts, coil or leaf.
__________________
44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
