motor swap mount question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

kljfamily · 03-02-2021, 01:43 PM

Hello,

1965 c10 inline 230 (Bad motor been bored over too many times)

I was finally able to source a replacement motor for my 65.

The motor is from a 1978 c10 inline 250 (Good running motor)

Forgive my lack of understanding of motor mounts but I am a bodywork guy trying to learn.

The mounts look very different. With the 78 mount sit on the stock perch? Will the 65 mounts fit the 78?

What is the best way to mount this motor?

thanks

**PGSigns** · 03-02-2021, 08:06 PM

Unbolt the 65 mounts from the block and bolt em to the new motor.
Jimmy

kljfamily · 03-02-2021, 08:11 PM

thanks, looking at the block its the same pattern so that makes a lot of sense.

next question.... does anyone have a pic of how the mounts go on? Orientation/bolt wise?

Ive ordered me factory assembly manual but waiting on the post office.

I took everything about down to frame. So now just which direction everything faces??

kljfamily · 03-02-2021, 09:26 PM

I found the answer in searching the forums here:
http://67-72chevytrucks.com/vboard/s...d.php?t=523133

thanks all

Nappers · 03-02-2021, 10:25 PM

Glad you got it sorted. My '64 had a 230 and a 350 bolted with new motor mounts without changing anything. In case you go that route later. I think 63 on same mounts for V8 and I6?????

**cwcarpenter98** · 03-03-2021, 01:36 PM

Quote:

Originally Posted by Nappers

Glad you got it sorted. My '64 had a 230 and a 350 bolted with new motor mounts without changing anything. In case you go that route later. I think 63 on same mounts for V8 and I6?????

For 63-66, the v8s and the 230 and 250 straight 6s used the same frame stands. The 292 straight 6 used the same driver's side stand, but the passenger side was different. GM used different stands for straight 6 or v8s on the 67-72 trucks

Nappers · 03-03-2021, 02:23 PM

Quote:

Originally Posted by cwcarpenter98

For 63-66, the v8s and the 230 and 250 straight 6s used the same frame stands. The 292 straight 6 used the same driver's side stand, but the passenger side was different. GM used different stands for straight 6 or v8s on the 67-72 trucks

YES! I forgot about the 292. Then they change for 67-72!

Thanks for clarifying! Someone told me they were the same 63 on.

kaycee · 03-06-2021, 11:39 AM

OK think I found the answer to my motor mount fiasco ,my drivers side is allmost lined up ,but the pass. side is way off. This truck must of had a 292 in
it at one time.Bought it with the 350 installed and have been finding all kinds of suprises. The towers are welded to the frame plus I found the drivers mount allso has a 1/2" spacer between the mount and tower

03-02-2021, 01:43 PM	#1
kljfamily Registered User Join Date: Sep 2014 Location: Albuquerque NM Posts: 98	motor swap mount question Hello, 1965 c10 inline 230 (Bad motor been bored over too many times) I was finally able to source a replacement motor for my 65. The motor is from a 1978 c10 inline 250 (Good running motor) Forgive my lack of understanding of motor mounts but I am a bodywork guy trying to learn. The mounts look very different. With the 78 mount sit on the stock perch? Will the 65 mounts fit the 78? What is the best way to mount this motor? thanks

03-02-2021, 08:06 PM	#2
PGSigns Senior Member Join Date: Jan 2011 Location: Hayes Va Posts: 4,569	Re: motor swap mount question Unbolt the 65 mounts from the block and bolt em to the new motor. Jimmy __________________ 60 to 66 Chevy and GMC window decals http://67-72chevytrucks.com/vboard/s...d.php?t=661131 Good friends, good food and a hotrod what else do you need? 1966 BBW long fleet Daily driver 1965 BBW short fleet Sold and going to a good home 1965 Suburban 2003 3500 Duramax 2005 Ultra Classic

03-02-2021, 08:11 PM	#3
kljfamily Registered User Join Date: Sep 2014 Location: Albuquerque NM Posts: 98	Re: motor swap mount question thanks, looking at the block its the same pattern so that makes a lot of sense. next question.... does anyone have a pic of how the mounts go on? Orientation/bolt wise? Ive ordered me factory assembly manual but waiting on the post office. I took everything about down to frame. So now just which direction everything faces??

03-02-2021, 09:26 PM	#4
kljfamily Registered User Join Date: Sep 2014 Location: Albuquerque NM Posts: 98	Re: motor swap mount question I found the answer in searching the forums here: http://67-72chevytrucks.com/vboard/s...d.php?t=523133 thanks all

03-02-2021, 10:25 PM	#5
Nappers Registered User Join Date: Sep 2018 Location: Yreka, CA Posts: 43	Re: motor swap mount question Glad you got it sorted. My '64 had a 230 and a 350 bolted with new motor mounts without changing anything. In case you go that route later. I think 63 on same mounts for V8 and I6?????

03-06-2021, 11:39 AM	#8
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,446	Re: motor swap mount question OK think I found the answer to my motor mount fiasco ,my drivers side is allmost lined up ,but the pass. side is way off. This truck must of had a 292 in it at one time.Bought it with the 350 installed and have been finding all kinds of suprises. The towers are welded to the frame plus I found the drivers mount allso has a 1/2" spacer between the mount and tower __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.