starter issue - The 1947 - Present Chevrolet & GMC Truck Message Board Network

hdixon · 08-27-2021, 10:27 PM

Can anyone help me out having starter issue has anyone had a problem where starter just chicks When I turn the switch it want turn the engine over I have change the battery However I can take a jumper wire from the battery and connect it to the starter and it will start I don't understand what's going on at this point any help would be great sometimes it will crank then there are times when it just chicks and not start

**LockDoc** · 08-27-2021, 10:43 PM

-
If you haven't already I would remove all of the battery cables and scrape or wire brush all of the terminals and metal that they connect to. It could be the contact disk inside the solenoid but I wouldn't think it would start with the jumper cables either if it was that....

LockDoc

tommy3horse · 08-28-2021, 12:35 AM

Mine does that too, could it be the ignition switch corrosion?

hdixon · 08-28-2021, 12:36 AM

Thanks this is a new build new painless wire harness I go out after a few days to try and it starts up with no charge on the battery or anything I installed a new battery same problem I am using a 0/1 welding cable from the battery straight to the starter that want cause any issue would it? I was wondering do I have anything connected incorrectly that's causing the problem

BigBird05 · 08-28-2021, 08:32 AM

Can you get to the purple on at the starter starter? Try to put 12V to that stud. If it just clicks you have a bad solenoid.

**dmjlambert** · 08-28-2021, 10:59 AM

Mine was doing that and it was because I had an "emergency repair" type battery terminal like this where the main wire is pinched by a plate. They are not good. Is that the type of battery terminal you have?

08-27-2021, 10:27 PM	#1
hdixon Registered User Join Date: Aug 2016 Location: Plantation, Fl Posts: 357	starter issue Can anyone help me out having starter issue has anyone had a problem where starter just chicks When I turn the switch it want turn the engine over I have change the battery However I can take a jumper wire from the battery and connect it to the starter and it will start I don't understand what's going on at this point any help would be great sometimes it will crank then there are times when it just chicks and not start

08-27-2021, 10:43 PM	#2
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,818	Re: starter issue - If you haven't already I would remove all of the battery cables and scrape or wire brush all of the terminals and metal that they connect to. It could be the contact disk inside the solenoid but I wouldn't think it would start with the jumper cables either if it was that.... LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

08-28-2021, 12:35 AM	#3
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 124	Re: starter issue Mine does that too, could it be the ignition switch corrosion? __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

08-28-2021, 12:36 AM	#4
hdixon Registered User Join Date: Aug 2016 Location: Plantation, Fl Posts: 357	Re: starter issue Thanks this is a new build new painless wire harness I go out after a few days to try and it starts up with no charge on the battery or anything I installed a new battery same problem I am using a 0/1 welding cable from the battery straight to the starter that want cause any issue would it? I was wondering do I have anything connected incorrectly that's causing the problem

08-28-2021, 08:32 AM	#5
BigBird05 Registered User Join Date: Aug 2019 Location: Cheraw Posts: 1,300	Re: starter issue Can you get to the purple on at the starter starter? Try to put 12V to that stud. If it just clicks you have a bad solenoid.

08-28-2021, 10:59 AM	#6
dmjlambert Senior Member Join Date: Apr 2016 Location: Cypress, TX Posts: 3,884	Re: starter issue Mine was doing that and it was because I had an "emergency repair" type battery terminal like this where the main wire is pinched by a plate. They are not good. Is that the type of battery terminal you have?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.