QA1 install on my Sons Truck. (Pics) - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cjohnson6772 · 12-02-2021, 10:43 PM

Quote:

Originally Posted by 1970 CST Short Wide

Moved the front up 1/4 inch. All is well

Been too busy with the technical questions to comment, but that is a beautiful truck!

**1970 CST Short Wide** · 12-03-2021, 01:35 AM

Quote:

Originally Posted by cjohnson6772

Been too busy with the technical questions to comment, but that is a beautiful truck!

Thank You. Just ordered widened rear tubs, I must have wider tires in the rear. Time will tell where this goes. LOL

LakeAnna · 12-03-2021, 05:45 AM

Quote:

Originally Posted by 1970 CST Short Wide

Thank You. Just ordered widened rear tubs, I must have wider tires in the rear. Time will tell where this goes. LOL

Looks good and I bet it rides nice now!

3767 · 12-03-2021, 06:43 AM

When u get the wider rear tubs n place then you will go even more down the rabbit hole and get the wider front tubs ….lmao. Looks like 315’s and forged rims are n the future 4 you.

cst350 · 12-08-2021, 04:34 PM

I just finished installing the rear kit for stock trailing arms. Rides way better than my last set-up of Ridetech RC shocks @ 6" ECE lowering springs. I will say that once you get to the part of the instructions that say "some trimming may be required to fit brackets onto stock arms" take a deep breath! I'm the type that troubleshoots with a scalpel rather than a chainsaw. I stated with a grinder and ended with a sawzall. Took a lot of passes (a little bit at a time) to get the brackets on. Then when I went to bolt on the Coil-over bracket the bolts hit the TA and I had to trim some more. Would be great if QA-1 had some templates to show how to trim. Now that it's all together I am stoked so all the work and headache was worth it.

**1970 CST Short Wide** · 12-08-2021, 04:46 PM

Nice. If you add the QA Sway Bar it will improve even more

12-03-2021, 06:43 AM	#54
3767 Registered User Join Date: Aug 2019 Location: Vale,nc Posts: 171	Re: QA1 install on my Sons Truck. (Pics) When u get the wider rear tubs n place then you will go even more down the rabbit hole and get the wider front tubs ….lmao. Looks like 315’s and forged rims are n the future 4 you.

12-08-2021, 04:34 PM	#55
cst350 Registered User Join Date: Dec 2003 Location: nor cal Posts: 219	Re: QA1 install on my Sons Truck. (Pics) I just finished installing the rear kit for stock trailing arms. Rides way better than my last set-up of Ridetech RC shocks @ 6" ECE lowering springs. I will say that once you get to the part of the instructions that say "some trimming may be required to fit brackets onto stock arms" take a deep breath! I'm the type that troubleshoots with a scalpel rather than a chainsaw. I stated with a grinder and ended with a sawzall. Took a lot of passes (a little bit at a time) to get the brackets on. Then when I went to bolt on the Coil-over bracket the bolts hit the TA and I had to trim some more. Would be great if QA-1 had some templates to show how to trim. Now that it's all together I am stoked so all the work and headache was worth it. Attached Images

12-08-2021, 04:46 PM	#56
1970 CST Short Wide Senior Moment Join Date: Mar 2002 Location: Pittsburg Ca Posts: 4,185	Re: QA1 install on my Sons Truck. (Pics) Nice. If you add the QA Sway Bar it will improve even more __________________ 1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.