1968 C10 SWB AZ build - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

TK1636 · 06-30-2021, 03:36 PM

First drive before I put on the front end and bed.

https://youtu.be/srWFSAcPePw

TK1636 · 06-30-2021, 03:42 PM

Quote:

Originally Posted by 88Stanger

Great looking ride there sir. Gotta love the AN Fittings. As you mentioned, not cheap, but they are nice looking, work great and are easy to install once you get them made up.
Great job!

I hate the rubber lines with the hose clamps, and I am not very good at bending steel fuel lines.

Quote:

Originally Posted by Kronald_70GMC

Nice truck! Sounds mean

Thank you sir it has been a labor of love. I enjoy this truck a lot more than my S-10 I raced.

TK1636 · 06-30-2021, 05:43 PM

Finally with the bed on.

https://youtu.be/1Sm67FldPj0

Low Elco · 06-30-2021, 07:39 PM

Not for nuthin, if your front tires are that far back in the well, your front upper a arms are swapped side-side. Had it happen myself. Easy to fix. Check it out befor you send ti to alignment. Neat ol truck!

TK1636 · 06-30-2021, 09:33 PM

Quote:

Originally Posted by Low Elco

Not for nuthin, if your front tires are that far back in the well, your front upper a arms are swapped side-side. Had it happen myself. Easy to fix. Check it out befor you send ti to alignment. Neat ol truck!

I am going to have to look into this.

TK1636 · 07-13-2021, 11:11 PM

Finally got my bumper brackets, so now I have a license plate light. Now I just need a tailgate.

TK1636 · 12-29-2021, 10:30 PM

Finally got my tailgate and rims. Also got the posi put in,now I can drive it and enjoy it!

TK1636 · 12-29-2021, 10:32 PM

New engine from smeding, more horse power and more reliable. Just a little expensive but I don't see my self getting rid of these truck.

TK1636 · 12-29-2021, 10:52 PM

https://youtu.be/4d1ZbL5DOrQ

TK1636 · 02-22-2022, 09:14 PM

Took the truck out and got some pictures of around town.

**twotrucks** · 03-05-2022, 09:34 AM

Great looking truck. I really like the exhaust work. Were you able to use the factory transmission crossmember?

TK1636 · 03-05-2022, 10:21 AM

I used the crossmembers from POL, as I wanted to tuck the exhaust up as much as possible.

Trans crossmember
https://www.performanceonline.com/19...RoCt1IQAvD_BwE

Trailing arm crossmember
https://www.performanceonline.com/19...hoCTYAQAvD_BwE

TK1636 · 03-05-2022, 10:24 AM

Try to launch the truck over the weekend, probably going to need slicks.

I stalled up and then punched it, then had to feather the throttle but still spun.
https://www.youtube.com/watch?v=lbI7IAHNF2U

No stall just feathering the throttle pedal but still spun a little
https://www.youtube.com/watch?v=wX-WSiCwklg

LT7A · 03-05-2022, 03:53 PM

I really like your truck. You've done a lot to overcome what time did to beat on it. Very clean work. I hope you are really enjoying driving it.

TK1636 · 03-05-2022, 04:38 PM

Quote:

Originally Posted by LT7A

I really like your truck. You've done a lot to overcome what time did to beat on it. Very clean work. I hope you are really enjoying driving it.

I am enjoying it very much, just not enjoying the gas prices right now. There is going to be a big truck show next Saturday in my town so i will be taking it out for that and getting a ton of pictures with other truck.

TK1636 · 03-18-2022, 02:22 PM

Had a small C-10 truck show in my small town, people from Phoenix and Tucson came down.

TK1636 · 03-18-2022, 02:32 PM

Mine still has a way to go to look as good as the other trucks. I wanted to get mine running and drive able before I start doing the body work.

**GSFMECH** · 03-18-2022, 03:03 PM

That's a cool build, it's looking good. Drive the wheels off it now.

06-30-2021, 03:36 PM	#26
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build First drive before I put on the front end and bed. https://youtu.be/srWFSAcPePw

06-30-2021, 05:43 PM	#28
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Finally with the bed on. https://youtu.be/1Sm67FldPj0 Last edited by TK1636; 06-30-2021 at 06:05 PM.

06-30-2021, 07:39 PM	#29
Low Elco Registered User Join Date: Apr 2003 Location: Indep, MO Posts: 5,893	Re: 1968 C10 SWB AZ build Not for nuthin, if your front tires are that far back in the well, your front upper a arms are swapped side-side. Had it happen myself. Easy to fix. Check it out befor you send ti to alignment. Neat ol truck! __________________ Boppa's Old Yeller Truck Build, Old Yeller's New Heart! Project Buzz Bomb Flyin' Low!

07-13-2021, 11:11 PM	#31
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Finally got my bumper brackets, so now I have a license plate light. Now I just need a tailgate. Attached Images

12-29-2021, 10:30 PM	#32
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Finally got my tailgate and rims. Also got the posi put in,now I can drive it and enjoy it! Attached Images

12-29-2021, 10:32 PM	#33
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build New engine from smeding, more horse power and more reliable. Just a little expensive but I don't see my self getting rid of these truck.

12-29-2021, 10:52 PM	#34
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build https://youtu.be/4d1ZbL5DOrQ

02-22-2022, 09:14 PM	#35
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Took the truck out and got some pictures of around town. Attached Images

03-05-2022, 09:34 AM	#36
twotrucks Junior Member Join Date: Jun 2003 Location: Louisville,Ky Posts: 383	Re: 1968 C10 SWB AZ build Great looking truck. I really like the exhaust work. Were you able to use the factory transmission crossmember?

03-05-2022, 10:21 AM	#37
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build I used the crossmembers from POL, as I wanted to tuck the exhaust up as much as possible. Trans crossmember https://www.performanceonline.com/19...RoCt1IQAvD_BwE Trailing arm crossmember https://www.performanceonline.com/19...hoCTYAQAvD_BwE

03-05-2022, 10:24 AM	#38
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Try to launch the truck over the weekend, probably going to need slicks. I stalled up and then punched it, then had to feather the throttle but still spun. https://www.youtube.com/watch?v=lbI7IAHNF2U No stall just feathering the throttle pedal but still spun a little https://www.youtube.com/watch?v=wX-WSiCwklg

03-05-2022, 03:53 PM	#39
LT7A Registered User Join Date: Oct 2015 Location: PNW Posts: 3,627	Re: 1968 C10 SWB AZ build I really like your truck. You've done a lot to overcome what time did to beat on it. Very clean work. I hope you are really enjoying driving it.

03-18-2022, 02:22 PM	#41
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Had a small C-10 truck show in my small town, people from Phoenix and Tucson came down. Attached Images

03-18-2022, 02:32 PM	#42
TK1636 Registered User Join Date: Nov 2019 Location: Casa Grande Arizona Posts: 39	Re: 1968 C10 SWB AZ build Mine still has a way to go to look as good as the other trucks. I wanted to get mine running and drive able before I start doing the body work. Attached Images

03-18-2022, 03:03 PM	#43
GSFMECH On the road Join Date: Jan 2004 Location: NATCHITOCHES LOUISIANA Posts: 818	Re: 1968 C10 SWB AZ build That's a cool build, it's looking good. Drive the wheels off it now. __________________ Mike Castro- 72 SWB. Ochre and White. 496/400 turbo, GV OD ,Dakota Digital dash , tilt, Vintage Air, PS, hydro boost, factory buckets, console, QA-1 Coil over suspension, 20/20"Billet Specialties Magnetos 72 SWB. Med blue. 454/400 turbo, tach, tilt, Stock AC, PS,PDB, factory buckets, console, ECE 4/6 drop w/ 2" blocks and C-notch, 20/20"Coys- Crashed and destroyed by drunk driver Sept 2019. New 72 build in the works. My new build thread "Castro" https://67-72chevytrucks.com/vboard/...d.php?t=820934 My old build thread, the blue truck http://67-72chevytrucks.com/vboard/s...d.php?t=271489 www.louisianaclassictruckclub.com



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.