is Tip and Flip cab dolly available? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**landarts** · 08-15-2019, 12:11 PM

Getting closer, was able to get the bottom and diagonal braces welded in. Also added the four bottom diagonal supports for the legs. Drilled the holes for the supports and started getting it ready for some paint. Second pictures shows the dimensions I used for the cart so that the cab will properly. I drilled the holes larger than needed to adjust for some wiggle room.

**landarts** · 08-18-2019, 05:24 PM

Finally got it done and testing today with the K10 cab. Next I will need to test the tilt function. Really like the working heighth of the cab now and works well for my lower back issues.

Patch · 07-14-2020, 02:04 PM

I know this thread is a bit old, but how did it all turn out? Tip function work okay? I'm in the planning stages on building mine and like a few different ideas from each one I've seen.

**landarts** · 07-14-2020, 02:22 PM

It has been working great. the tip function of the cart has really worked out good. I am now getting geared up for phase two of the build on the cart. I am building additional implements to mount doors, fenders etc for body work and painting.

Patch · 07-20-2020, 07:36 PM

So I am going to go with the original tip & flip design and ordered my metal today. His plans show the wheels getting welded directly to the main frame. There's no reason why I can't weld a mounting plate to that frame so I can bolt and unbolt a wheel in case of failure is there?

**ThreeQuarter** · 07-20-2020, 07:46 PM

I ended up using the casters he spec’ed, and I can’t remember if the bolt holes were wide enough to clear the width of the tubing they were welded to. Sorry, I can’t check mine because I sold it, but it would be something to verify before you bought/cut the flat metal for this. At worst you could tack the casters and grind them off in case of failure.

gmc684x4 · 07-21-2020, 01:59 AM

You could weld plates to the tube so you can bolt the caster wheels to yhe cart if tubing narrower then caster plate

**D.PASSMORE** · 07-22-2020, 10:30 AM

I have the metal cut for mine, need to start the welding process. why did you use rubber wheel casters? I would be hesitant because of the welding sparks blowing the tires. No problems?

**landarts** · 07-22-2020, 02:06 PM

I used pneumatic tires because I can wheel it to my side yard where there is gravel. If it was only staying in the garage on concrete I would gave used hard rubber. Welding sparks are not an issue, did all rust repair and grinding and it was not an issue.

rx78nt1alex · 09-10-2020, 11:36 PM

Landarts, so do those mounting plates that the cab mounts to, are those removable, as it looks like they insert into the top of the dolly. If so, then making this into a dolly cart easy for the bed.

I’d like to roll the bed sideways to work on it.

**landarts** · 09-11-2020, 08:10 AM

Yes they a removable. I have made a few other arms to go on it to hold doors, bedsides, fenders etc., next time I have it in that configuration I will post some pictures.

indianpride77 · 10-16-2022, 10:34 AM

Did they happen to make these for the 73-87??

**Getter-Done** · 10-16-2022, 11:29 AM

Quote:

Originally Posted by indianpride77

Did they happen to make these for the 73-87??

It would not be hard to make one if you have the tools and equipment.
Here is a thread with some dimensions.

Link: https://67-72chevytrucks.com/vboard/...ight=cab+dolly

08-15-2019, 12:11 PM	#26
landarts landarts Join Date: May 2005 Location: Star, Idaho Posts: 1,420	Re: is Tip and Flip cab dolly available? Getting closer, was able to get the bottom and diagonal braces welded in. Also added the four bottom diagonal supports for the legs. Drilled the holes for the supports and started getting it ready for some paint. Second pictures shows the dimensions I used for the cart so that the cab will properly. I drilled the holes larger than needed to adjust for some wiggle room. Attached Images __________________ Super Cheyenne aka the "Devil Cowboy" 71 K20 Idaho Edition 69 K10 from the Field 68 Second Chance Fix and Sale 72 GMC 3/4 ton 4x4 K2500 The "Fixrupr" build thread 72 Cheyenne 1/2 ton " FIXRUPR " - daily driver 67 C20 all original paint 71 K20 Custom 4x4 (Idaho Edition) 72 K20 GMC Super Custom 4x4 72 K20 Custom Deluxe 4x4 69 K10 Custom package 4x4 (69 K10 from the field) 72 K10 Custom 71 K10 Custom 72 K20 Custom Deluxe 4x4 72 K20 Crew Cab Project 71 GMC Jimmy CST 72 Blazer 70 Blazer

08-18-2019, 05:24 PM	#27
landarts landarts Join Date: May 2005 Location: Star, Idaho Posts: 1,420	Re: is Tip and Flip cab dolly available? Finally got it done and testing today with the K10 cab. Next I will need to test the tilt function. Really like the working heighth of the cab now and works well for my lower back issues. Attached Images __________________ Super Cheyenne aka the "Devil Cowboy" 71 K20 Idaho Edition 69 K10 from the Field 68 Second Chance Fix and Sale 72 GMC 3/4 ton 4x4 K2500 The "Fixrupr" build thread 72 Cheyenne 1/2 ton " FIXRUPR " - daily driver 67 C20 all original paint 71 K20 Custom 4x4 (Idaho Edition) 72 K20 GMC Super Custom 4x4 72 K20 Custom Deluxe 4x4 69 K10 Custom package 4x4 (69 K10 from the field) 72 K10 Custom 71 K10 Custom 72 K20 Custom Deluxe 4x4 72 K20 Crew Cab Project 71 GMC Jimmy CST 72 Blazer 70 Blazer

07-14-2020, 02:04 PM	#28
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Re: is Tip and Flip cab dolly available? I know this thread is a bit old, but how did it all turn out? Tip function work okay? I'm in the planning stages on building mine and like a few different ideas from each one I've seen. __________________ Patch

07-14-2020, 02:22 PM	#29
landarts landarts Join Date: May 2005 Location: Star, Idaho Posts: 1,420	Re: is Tip and Flip cab dolly available? It has been working great. the tip function of the cart has really worked out good. I am now getting geared up for phase two of the build on the cart. I am building additional implements to mount doors, fenders etc for body work and painting. __________________ Super Cheyenne aka the "Devil Cowboy" 71 K20 Idaho Edition 69 K10 from the Field 68 Second Chance Fix and Sale 72 GMC 3/4 ton 4x4 K2500 The "Fixrupr" build thread 72 Cheyenne 1/2 ton " FIXRUPR " - daily driver 67 C20 all original paint 71 K20 Custom 4x4 (Idaho Edition) 72 K20 GMC Super Custom 4x4 72 K20 Custom Deluxe 4x4 69 K10 Custom package 4x4 (69 K10 from the field) 72 K10 Custom 71 K10 Custom 72 K20 Custom Deluxe 4x4 72 K20 Crew Cab Project 71 GMC Jimmy CST 72 Blazer 70 Blazer

07-20-2020, 07:36 PM	#30
Patch Senior Member Join Date: Jul 2002 Location: Oak Harbor, WA Posts: 709	Re: is Tip and Flip cab dolly available? So I am going to go with the original tip & flip design and ordered my metal today. His plans show the wheels getting welded directly to the main frame. There's no reason why I can't weld a mounting plate to that frame so I can bolt and unbolt a wheel in case of failure is there? __________________ Patch

07-20-2020, 07:46 PM	#31
ThreeQuarter Senior Member Join Date: Jun 2000 Location: Texan in Iowa Posts: 2,522	Re: is Tip and Flip cab dolly available? I ended up using the casters he spec’ed, and I can’t remember if the bolt holes were wide enough to clear the width of the tubing they were welded to. Sorry, I can’t check mine because I sold it, but it would be something to verify before you bought/cut the flat metal for this. At worst you could tack the casters and grind them off in case of failure. __________________ Ben '68 Chevy C10 Custom LWB 327/TH400 2nd owner '16 GMC Sierra 1500 SLE Dblcab 4wd 5.3

07-21-2020, 01:59 AM	#32
gmc684x4 Registered User Join Date: Jul 2012 Location: Whitehorse yukon Posts: 1,218	Re: is Tip and Flip cab dolly available? You could weld plates to the tube so you can bolt the caster wheels to yhe cart if tubing narrower then caster plate

07-22-2020, 10:30 AM	#33
D.PASSMORE One of the First Join Date: Jan 2000 Location: St. Augustine,FL. Posts: 4,059	Re: is Tip and Flip cab dolly available? I have the metal cut for mine, need to start the welding process. why did you use rubber wheel casters? I would be hesitant because of the welding sparks blowing the tires. No problems? __________________ DAVID PASSMORE ST AUGUSTINE ,FL ZIP 32084 '71 SWB K/10 CUSTOM DELUXE (Chili) '72 BLAZER K/5 Muscle Truck (Mule) '72 LWB K/20 CHEYENNE (Blackie)

07-22-2020, 02:06 PM	#34
landarts landarts Join Date: May 2005 Location: Star, Idaho Posts: 1,420	Re: is Tip and Flip cab dolly available? I used pneumatic tires because I can wheel it to my side yard where there is gravel. If it was only staying in the garage on concrete I would gave used hard rubber. Welding sparks are not an issue, did all rust repair and grinding and it was not an issue. __________________ Super Cheyenne aka the "Devil Cowboy" 71 K20 Idaho Edition 69 K10 from the Field 68 Second Chance Fix and Sale 72 GMC 3/4 ton 4x4 K2500 The "Fixrupr" build thread 72 Cheyenne 1/2 ton " FIXRUPR " - daily driver 67 C20 all original paint 71 K20 Custom 4x4 (Idaho Edition) 72 K20 GMC Super Custom 4x4 72 K20 Custom Deluxe 4x4 69 K10 Custom package 4x4 (69 K10 from the field) 72 K10 Custom 71 K10 Custom 72 K20 Custom Deluxe 4x4 72 K20 Crew Cab Project 71 GMC Jimmy CST 72 Blazer 70 Blazer

09-10-2020, 11:36 PM	#35
rx78nt1alex Registered User Join Date: Jul 2013 Location: CEDAR HILL, TX Posts: 43	Re: is Tip and Flip cab dolly available? Landarts, so do those mounting plates that the cab mounts to, are those removable, as it looks like they insert into the top of the dolly. If so, then making this into a dolly cart easy for the bed. I’d like to roll the bed sideways to work on it. __________________ 1968 Chevrolet Fleetside C-10 1971 Chevrolet Fleetside C-10

09-11-2020, 08:10 AM	#36
landarts landarts Join Date: May 2005 Location: Star, Idaho Posts: 1,420	Re: is Tip and Flip cab dolly available? Yes they a removable. I have made a few other arms to go on it to hold doors, bedsides, fenders etc., next time I have it in that configuration I will post some pictures. __________________ Super Cheyenne aka the "Devil Cowboy" 71 K20 Idaho Edition 69 K10 from the Field 68 Second Chance Fix and Sale 72 GMC 3/4 ton 4x4 K2500 The "Fixrupr" build thread 72 Cheyenne 1/2 ton " FIXRUPR " - daily driver 67 C20 all original paint 71 K20 Custom 4x4 (Idaho Edition) 72 K20 GMC Super Custom 4x4 72 K20 Custom Deluxe 4x4 69 K10 Custom package 4x4 (69 K10 from the field) 72 K10 Custom 71 K10 Custom 72 K20 Custom Deluxe 4x4 72 K20 Crew Cab Project 71 GMC Jimmy CST 72 Blazer 70 Blazer

10-16-2022, 10:34 AM	#37
indianpride77 Registered User Join Date: Oct 2009 Location: lacey,wa Posts: 63	Re: is Tip and Flip cab dolly available? Did they happen to make these for the 73-87??



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.