|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-08-2004, 01:28 AM
|
#1 |
|
Registered User
Join Date: Apr 2004
Location: Chinle, Arizona
Posts: 60
|
2pc. driveshaft needed
I'm in need of a 2pc. driveshaft for a SWB TH350 short tail, if they even make one. Have problems with the the 1pc knocking against the crossmember.
|
|
|
|
08-08-2004, 06:24 AM
|
#2 |
|
Registered User
Join Date: Dec 1999
Location: BRADENTON FLA
Posts: 3,269
|
If you were closer i could fix you up, i have 9 of them and the carrier bearing mounts but shipping to AZ would be 30-35.00.
__________________
Rest in Peace Ed. Thanks for all the good times. |
|
|
|
|
08-08-2004, 12:21 PM
|
#3 |
|
"Trucks with Class"
 
Join Date: Jul 2000
Location: OLYMPIA, WA, USA
Posts: 8,134
|
I just pulled one out of a SWB. It is inside, clean & protected. PM for details.
|
|
|
|
|
08-08-2004, 12:30 PM
|
#4 |
|
Chevy Freak
Join Date: Sep 2002
Location: Meadville, Pa.
Posts: 2,804
|
Driveshaft
$50 shipped to you. Just pulled out of a 72 shortbed. Brian
__________________
69 GMC SWB, 350 70 Chevy LWB, 350 55 chevy gasser, 461 73 Camaro, 496 67 RS Camaro, 406 64 Chevelle, 588 71 Nova, 565 67 Camaro, 461 |
|
|
|
|
08-08-2004, 11:59 PM
|
#5 |
|
"Trucks with Class"
Join Date: Jul 2000
Location: OLYMPIA, WA, USA
Posts: 8,134
|
I yield to Burnsman...I can't pull, store, box, deliver and ship a driveshaft for $50...that's a "freebie"...go for it!
Last edited by PICKMUP; 08-09-2004 at 02:06 PM. |
|
|
|
|
08-09-2004, 09:44 AM
|
#6 |
|
Senior Moment
 
Join Date: Mar 2002
Location: Pittsburg Ca
Posts: 4,156
|
Why is it knocking on the crossmember????? When you put in the 1 piece did you remove the carrier bearing bracket?? I have a 1 piece and have NO problems
I'd check out WHY 1st. a 1 piece is much better
__________________
1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565 |
|
|
|
|
08-10-2004, 01:35 AM
|
#7 |
|
Registered User
Join Date: Apr 2004
Location: Chinle, Arizona
Posts: 60
|
Well I took out the lower bearing bracket when I restored the truck and just threw in a 1pc, now its lowered alittle and it's knocking pretty bad when I'm hauling my quad in the back.
|
|
|
|
|
08-10-2004, 09:50 AM
|
#8 |
|
Registered User
Join Date: Dec 1999
Location: BRADENTON FLA
Posts: 3,269
|
Take a torch,plasma cutter or sawzall and trim the crossmember a little bit at a time until it clears.
__________________
Rest in Peace Ed. Thanks for all the good times. |
|
|
|
|
08-10-2004, 09:53 AM
|
#9 |
|
Senior Moment
Join Date: Mar 2002
Location: Pittsburg Ca
Posts: 4,156
|
Where is it hitting?? When you haul your quad the truck goes down, are you sure your drive shaft isn’t to long and its bumping up against the tail housing??, Just a thought. My truck is lowered 3" front 4" rear and I have no problem with a load.
You also say you just threw in a 1 piece, where did it come from or did you have it made.
__________________
1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565 |
|
|
|
|
08-12-2004, 01:36 AM
|
#10 |
|
Registered User
Join Date: Apr 2004
Location: Chinle, Arizona
Posts: 60
|
Yes, I'm sure its knocking against the Crossmember, because I checked while I had a load in the back, and the shaft is about an inch from hitting the cross member. the shaft came from a wagon which fitted just right.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
