Bench Seat measurements - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Bodied67 · Yesterday, 09:50 AM

Question for you guys reguarding factory bench seats..

I got lowback seats in my 69, not sure what they’re from they were installed in the truck when I bought it, but I’d like to swap to a bench so I can take my lady and my son at the same time. My issue is that the previous owner also installed a floor shifter so I’m looking for a measurement of the back of the cab to the very front of the bench seat to see if I’ll be able to fit one without moving the shifter.

I do not have the gas tank in the cab it’s been relocated to the rear.

Any input would be great

**70STOVEBOLT** · Yesterday, 09:56 AM

I can get a measurement after work today, but I still have the tank behind the seat. Also, do you want the measurement with the seat all the way back?

Bodied67 · Yesterday, 10:15 AM

Quote:

Originally Posted by 70STOVEBOLT

I can get a measurement after work today, but I still have the tank behind the seat. Also, do you want the measurement with the seat all the way back?

Yea please! Anything would help!

**70STOVEBOLT** · Yesterday, 01:09 PM

Ok I will take a measurement when I get home and post it here. Do you want the measurement from the back wall of the cab to the front of the bottom cushion?

Bodied67 · Yesterday, 02:32 PM

Yes, the back of the cab behinds gas tank to wherever the front of the actual seat would end

kaycee · Yesterday, 05:35 PM

Keep in mind the seats usually hit the panel above tank and below rear window before it hits the tank.

**70STOVEBOLT** · Yesterday, 05:43 PM

I measured on the right side of the seat so the tank is not in the way. I got 29” from the back of the cab to the front edge of the bottom seat cushion. The seat is non-folding with it all the way back. You’re right the back of the seat at the top does hit the cab before it hits the tank.

Cal10 · Yesterday, 06:06 PM

I have a Muncie M21 and a bench seat in mine. Not sure what trans you’re running but I could take some measurements of the shifter location in relation to the seat if that would help. The Muncie shifter location sits pretty far back but it clears the bench without issues.
Posted via Mobile Device

Cal10 · Yesterday, 10:25 PM

Measurement from the dash to the seat (I still have the tank in the cab so it’s hard to get those numbers, but you can see where the shifter lands)

Yesterday, 09:50 AM	#1
Bodied67 Registered User Join Date: Aug 2013 Location: Poughkeepsie NY Posts: 37	Bench Seat measurements Question for you guys reguarding factory bench seats.. I got lowback seats in my 69, not sure what they’re from they were installed in the truck when I bought it, but I’d like to swap to a bench so I can take my lady and my son at the same time. My issue is that the previous owner also installed a floor shifter so I’m looking for a measurement of the back of the cab to the very front of the bench seat to see if I’ll be able to fit one without moving the shifter. I do not have the gas tank in the cab it’s been relocated to the rear. Any input would be great __________________ 67 SFBD C10 (sold) 69 C10 "Nosejob" 23 Raptor

Yesterday, 09:56 AM	#2
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,439	Re: Bench Seat measurements I can get a measurement after work today, but I still have the tank behind the seat. Also, do you want the measurement with the seat all the way back? __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

Yesterday, 01:09 PM	#4
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,439	Re: Bench Seat measurements Ok I will take a measurement when I get home and post it here. Do you want the measurement from the back wall of the cab to the front of the bottom cushion? __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

Yesterday, 02:32 PM	#5
Bodied67 Registered User Join Date: Aug 2013 Location: Poughkeepsie NY Posts: 37	Re: Bench Seat measurements Yes, the back of the cab behinds gas tank to wherever the front of the actual seat would end __________________ 67 SFBD C10 (sold) 69 C10 "Nosejob" 23 Raptor

Yesterday, 05:35 PM	#6
kaycee Registered User Join Date: Jan 2000 Location: Wyoming USA Posts: 2,454	Re: Bench Seat measurements Keep in mind the seats usually hit the panel above tank and below rear window before it hits the tank. __________________ 2001 Silverado K-1500 2005 FXDWG stage3 69 CHEVY Short/Step 327/4L60 373 posi 63 IMPALA 327/4L60

Yesterday, 05:43 PM	#7
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,439	Re: Bench Seat measurements I measured on the right side of the seat so the tank is not in the way. I got 29” from the back of the cab to the front edge of the bottom seat cushion. The seat is non-folding with it all the way back. You’re right the back of the seat at the top does hit the cab before it hits the tank. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear

Yesterday, 06:06 PM	#8
Cal10 Registered User Join Date: Feb 2022 Location: Fairfield, CA Posts: 57	Re: Bench Seat measurements I have a Muncie M21 and a bench seat in mine. Not sure what trans you’re running but I could take some measurements of the shifter location in relation to the seat if that would help. The Muncie shifter location sits pretty far back but it clears the bench without issues. Posted via Mobile Device

Yesterday, 10:25 PM	#9
Cal10 Registered User Join Date: Feb 2022 Location: Fairfield, CA Posts: 57	Re: Bench Seat measurements Measurement from the dash to the seat (I still have the tank in the cab so it’s hard to get those numbers, but you can see where the shifter lands) Attached Images __________________ 67 Short Step - 454 & Muncie 4-speed



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.