|
09-03-2004, 09:55 PM
|
#1 |
|
Registered User
Join Date: Oct 2002
Location: Virginia
Posts: 226
|
Fiberglass parts?
My truck has its fair share of rust, thanks mostly to a cheap previous owner and poor bodywork. Has anyone here considered a fiberglass cab? I am seriously considering going with a fiberglass hood, but how much would a fiberglass cab cost in comparison to extensive rust repair? Should i learn to do bodywork myself or just give up the ghost and buy a new cab? One thing is for sure on this one, whatever i do as far as bodywork goes, i don't want to have to do it again for a long, long time. Anybody have any advice?
|
|
|
|
09-03-2004, 10:09 PM
|
#2 |
|
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,448
|
I have seen fiberglass front caps, but I haven't seen an entire cab yet.
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal.  We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
|
|
|
|
09-03-2004, 10:10 PM
|
#3 |
|
Registered User
Join Date: Oct 2002
Location: Virginia
Posts: 226
|
That was half the reason for this post, i know i have seen complete cabs somewhere but i just couldn't remember where. I was hoping that someone could give me reccomendations.
|
|
|
|
|
09-03-2004, 10:20 PM
|
#4 |
|
The Blazer King
Join Date: Sep 2000
Location: Valrico, Fl (Tampa)
Posts: 1,212
|
I think MotherTruckers sells those.
__________________
72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest. |
|
|
|
|
09-03-2004, 10:49 PM
|
#5 |
|
Registered User
Join Date: Nov 2002
Location: Kelowna B.C. Canada
Posts: 1,086
|
Try this place http://www.usbody.com/
|
|
|
|
|
09-04-2004, 03:30 AM
|
#6 |
|
Registered User
Join Date: Dec 2002
Location: Tampa
Posts: 1,191
|
Yes, US Body has complete fiberglass cabs. Two of them in fact. One to replace the "stock" set up and one with out a floor to set up on your top fuel frame.
 I'm pretty sure that they were around $3,000-3,500.00. Ed at Mothertruckers is a authorized US Body dealer. I recently got my fiberglass one piece tilt from him. You can actually buy a cab, have it dipped and all the sheetmetal replaced for less than the price of a fiberglass unit. Give Ed a call on that too (as I recently just picked my new cab up from him also). Personally, I'd love to have a fiberglass cab though.Edit: They also have doors along with hoods and front ends. Quite a good selection in fact.
__________________
'68 Short Step LS1/T56, Hydratech, Fatman Fabrications Stage III, Baer, Hot Rods to Hell, US Body, S&W, etc |
|
|
|
|
09-04-2004, 07:43 AM
|
#7 |
|
Registered User
Join Date: Aug 2004
Location: Raleigh, NC
Posts: 36
|
what kind of truck is it? I have a 1pc fibreglass frnot end I am trying to sell. It was made for a 67 GMC but has a 69 Chevy grill molded into it. I would be willing to let it go for not much more than a fibreglass hood would cost. It's still in primer so it will still nrrd some finishing done. Also it has never been attached to my truck so there are no holes or cuts in it yet.
__________________
67 GMC LB (all in parts for now) |
|
|
|
|
09-05-2004, 01:07 AM
|
#8 |
|
Registered User
Join Date: Oct 2002
Location: Virginia
Posts: 226
|
Has anyone had any experience with the beds from USbody? I would love to get one but i was wondering how the fit would be.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
