![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,475
|
![]()
Well I got my kit from Tim Christian, Thanks buddy, and of course they did
not fit perfectly, have yet to here of someone's who did, a lil elbow grease, a few hours of my time, yes I said hours, and wala, what do ya all think. ![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
![]() |
![]() |
![]() |
#2 |
Account Suspended
Join Date: Sep 2000
Posts: 4,002
|
Cool, that would be a whole lot easier then bending a new set like I was planing on doing, I wonder if he sells a set for 2wds, the fuel lines would be nice to have premade too.
|
![]() |
![]() |
![]() |
#3 |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,475
|
2wd Is Available Also, It Was A Stainless Kit ( 4 Lines ) I Paid Like
$60 And Some Odd Cents, Fedex Shipped Direct To My Front Door. ![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
![]() |
![]() |
![]() |
#4 |
Account Suspended
Join Date: Sep 2000
Posts: 4,002
|
Did you just get the up front set or did you also get the lines that run to the rear?
|
![]() |
![]() |
![]() |
#5 |
Member since 2000
Join Date: Dec 2000
Location: Mountain View Ca / Mexico
Posts: 7,879
|
kits are nice but man when they get them wrong do they get them wrong. I also had to put in some work to get them right. On my next project I think I'll bend my own lines, after looking at some bare(show off) frames at the goodguys show, the way they setup there brake and fuel line looked like a work of art. Especially with all the cool products out on the market. Wish I took my camera so you guy can see what I'm talking about but I bet it take some practice to bend brake lines good.
![]() |
![]() |
![]() |
![]() |
#6 |
Account Suspended
Join Date: Sep 2000
Posts: 4,002
|
The bending is the easy and fun part, flaring the ends is were it gets tricky.
|
![]() |
![]() |
![]() |
#7 | |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,475
|
Quote:
![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
![]() |
![]() |
![]() |
#8 |
computer illiterate
Join Date: Jan 2001
Location: Des Moines, IA
Posts: 6,446
|
i think you should have painted the master cylinder :-)
__________________
72 2wd blazer 72 swb 4x4 |
![]() |
![]() |
![]() |
#9 | |
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,475
|
Quote:
![]() ![]()
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
![]() |
![]() |
![]() |
Bookmarks |
|
|