67c10 build

[67ctener]

Hung the door and fender before welding the rocker in cab corner. I'm happy with fit and finish of it all.

[67ctener]

Much better then it was with all gm metal

[Elliot949]

Originally Posted by 67ctener

Posted via Mobile Device

Feels like a huge accomplishment that it finally rolls. No more jack stands! Rolled it out of the garage so I could clean yesterday sure was nice
Posted via Mobile Device

Did you have any problem with the ECE Panhard Bar clearing the Billet Diff cover?...

[Elliot949]

Originally Posted by 67ctener

Posted via Mobile Device

WOW Those Headers are AWESOME!!!!

[67ctener]

The rear pan hard bar was straight so I had a friend bend it for me to clear the diff cover. Thanks for the compliment there Sanderson bb8s

[Bennett68C10]

Really nice job with the rust repairs on the cab, wish my cab corners looked that good.

[67ctener]

Originally Posted by Bennett68C10

Really nice job with the rust repairs on the cab, wish my cab corners looked that good.

Thanks Keith. Pictures are a little deceiving, the back of the cab corners are a little bumpy but I think should smooth out fine

[jlsanborn]

What a *****IN update!!! Props on keeping the filler neck where it oughtta be Nice work on the metal! What welder do you have? Pulley setup is sick too!

[67ctener]

I bought a reproduction fender, don't remember the manufacture, and just kept fighting it to make it fit. I got so frustrated I cut up the fender and fixed my original. I'm officially a firm believer there is no replacement for oe metal

[67ctener]

The rear of the fender was so beat up I replaced it also

[67ctener]

Originally Posted by jlsanborn

What a *****IN update!!! Props on keeping the filler neck where it oughtta be Nice work on the metal! What welder do you have? Pulley setup is sick too!

Thanks sir. I've always been a fan of the in cab tank. I can understand the efi guys moving them but this big block is gonna be drinking right out of the cab. I've been using a miller 140. It's been great, my first time welding with gas and all I can say is wow

[67ctener]

No ebfabman but those sand disk sure clean up the welds nice

[Elliot949]

Originally Posted by 67ctener

The rear pan hard bar was straight so I had a friend bend it for me to clear the diff cover. Thanks for the compliment there Sanderson bb8s

Can you get me a pic of how you bent that panhard on the truck?... I am looking at doing that...
That Chassis just looks awesome... Great work going on the cab... I also did a complete new bed... That sure has save me alot of time... Dan

[67ctener]

Driver side was about the same as far as work but only partial inner rocker and this side needed a little bit of the floor pan

[67ctener]

I lucked out, all the cab supports were good so I just hit them with some rust converter and primed them

[67ctener]

Had to split the rocker on this side to get it to align with the door

[fastcam1]

Someone's been busy, build looks awesome keep up the
good work!

[original-71]

very nice updates, looking good

[67ctener]

Thanks Cameron, how's yours coming along? Hope to attend my first meet next year with my truck. Hector I ended up going with your tires size, looks much better now in my opinion. Can't wait to see those rally's on your truck.

[fastcam1]

Haven't made much progress but I hope to bend up all of my brake lines starting next week.

[67ctener]

Rust is evil. Found a little more when trying to fill a pin hole. Took a 2" wholesale and made a series of holes till I found no more rust

[67ctener]

Not sure why it posted sideways, hope this ones better. Got it welded up and it finished nicely

[67ctener]

Hope this pic turns out or I don't know what to do. Finished up both fenders, not sure it was worth the time but there both original and fit great

[Molberg]

nice metal work... keep it up!

[Mr Chevorlet]

looking good great metal work