The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board > 67-72 Chevrolet & GMC Pickups Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-13-2019, 10:16 PM   #326
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Here’s the frame section cut out...it’s a little different then my first rendition. Note I am keeping the bottom section of the donor frame. The 3/4 ton frame height is 6 inches whereas the 1 ton frame is 7 inches. To use the original shackle mount, I’ll mount it to this bottom rail...using all original bolt holes.
Attached Images
  
fishnixon is offline   Reply With Quote
Old 10-13-2019, 10:19 PM   #327
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Here’s where it’ll go.
Attached Images
 
fishnixon is offline   Reply With Quote
Old 10-13-2019, 10:25 PM   #328
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Here’s a look from the inside of the frame. I’ll put some sort of support between the donor frame and the 1 ton frame...plus I’ll figure out how to incorporate a support to the trans crossmember.
Attached Images
  
fishnixon is offline   Reply With Quote
Old 10-13-2019, 10:30 PM   #329
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Quote:
Originally Posted by Getter-Done View Post
Looking good.

That is a Great plan you have in place.
I am taking notes
Just my input.
Tack and fit inside of the frame rail 1st.
Cause the outside will be easier to grind shape and re-weld.






.
Thanks...sounds good.
fishnixon is offline   Reply With Quote
Old 12-17-2019, 08:19 PM   #330
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Received my spacers recently. These are what you need if you want to put your “Bud” Dually style front wheels onto a 3/4 ton hub. They are STEEL, 2 3/4” deep, and these were ordered with factory 1/2” size studs. That way I’m not drilling out the 1967 2wd wheels. If you’re going to beat up the truck with off road stuff, then go with the 9/16” studs. Made in the USA. Check these guys out. I am a non-paid spokeman...heh heh
Attached Images
     

Last edited by fishnixon; 12-17-2019 at 08:50 PM.
fishnixon is offline   Reply With Quote
Old 12-17-2019, 08:24 PM   #331
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 8,413
Re: Dumptruck Dolly

Nice machine work.













.
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)


http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 12-17-2019, 08:36 PM   #332
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Wheel on. Nice spacing for steering components. I have mismatched locking differential hubs, so I’ll look into remedying that. I found it necessary to remove the locking hub to put on the spacers as there were bolt heads that exceeded the spacers inner diameter. No big deal.
Attached Images
   
fishnixon is offline   Reply With Quote
Old 12-17-2019, 08:44 PM   #333
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Quote:
Originally Posted by Getter-Done View Post
Nice machine work.













.
REAL Nice!
fishnixon is offline   Reply With Quote
Old 12-17-2019, 11:34 PM   #334
Ol Blue K20
Proprietor of Dale's Corner
 
Ol Blue K20's Avatar
 
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,245
Re: Dumptruck Dolly

Nice!
__________________
"Some Days Chickens And Some Days Feathers"

Dale
XNGH ECV Sam Brannan 1004

R.I.P. 67ChevyRedneck
R.I.P. Grumpy Old Man
R.I.P. FleetsidePaul
Ol Blue K20 is offline   Reply With Quote
Old 12-18-2019, 06:56 PM   #335
72 tigger
Registered User
 
72 tigger's Avatar
 
Join Date: Apr 2008
Location: Berne IN
Posts: 3,250
Re: Dumptruck Dolly

Looks really good
__________________
71 C10
72 K20
72 K10 Super
Kirk
72 tigger is offline   Reply With Quote
Old 12-25-2019, 04:58 PM   #336
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Merry Christmas!

Hope you all are having a memorable time today! During a break in the action, I snuck out to give some attention to Dolly. I am prepping to tack in the drivers side and am cutting out the passenger side frame for the new insert. You know what?! It’s going to happen this week!...rolling the front axle in for a test fit is imminent!
Attached Images
  
fishnixon is offline   Reply With Quote
Old 12-26-2019, 12:20 AM   #337
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

After more festivities, I got out to the garage again...

I tacked in the donor 3/4 ton frame pieces on both sides and bolted up the rear shackle support for the purpose of testing the alignment.

When it’s all said and done, I’ll gusset the bottom flange as well as make a lower support brace that’ll go to the crossmember.
Attached Images
  
fishnixon is offline   Reply With Quote
Old 12-26-2019, 12:25 AM   #338
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

I located my hardware for the leaf springs and bolted them on. I left it a smidgeon loose, so I can locate both ends of the spring easier into the hangers. I’ll tighten it down for the roll test and alignment.
Attached Images
  
fishnixon is offline   Reply With Quote
Old 12-26-2019, 12:30 AM   #339
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Man! I love the look of the bud wheel on the Dana 44. I can’t wait! I did a rough measurement of the front from outside to outside tread and came up with 69”. I then measured the rear end and came up with 81”. So, I’ll have a difference of 6” on each side comparing front to back...I don’t think that’s too bad...and nothing is going to change that anyway.
Attached Images
  

Last edited by fishnixon; 12-26-2019 at 12:40 AM.
fishnixon is offline   Reply With Quote
Old 12-26-2019, 12:31 AM   #340
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 8,413
Re: Dumptruck Dolly

Looking Good.
Merry Christmas.
The work you are doing will pay off.
You are making sure everything is
Squared and true.








.
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)


http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is offline   Reply With Quote
Old 12-26-2019, 12:38 AM   #341
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Quote:
Originally Posted by Getter-Done View Post
Looking Good.
Merry Christmas.
The work you are doing will pay off.
You are making sure everything is
Squared and true.








.
Merry Christmas!

Thank you...I’m trying to do it right. The thing that’s on my brain is the 3/4 ton donor frame portion and where I placed it on the Vertical plain. I should be ok. My thought about that was the vertical height difference of the K20 vs C30 and how the leaf spring would carry itself. I went with the 3/4 ton measurement since the Dana 44, the 4speed and transfer case all came from the same 3/4 ton donor vehicle.
fishnixon is offline   Reply With Quote
Old 12-27-2019, 12:59 PM   #342
Ol Blue K20
Proprietor of Dale's Corner
 
Ol Blue K20's Avatar
 
Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,245
Re: Dumptruck Dolly

Looking good!!
__________________
"Some Days Chickens And Some Days Feathers"

Dale
XNGH ECV Sam Brannan 1004

R.I.P. 67ChevyRedneck
R.I.P. Grumpy Old Man
R.I.P. FleetsidePaul
Ol Blue K20 is offline   Reply With Quote
Old 12-27-2019, 03:00 PM   #343
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Quote:
Originally Posted by Ol Blue K20 View Post
Looking good!!
Thank you!
fishnixon is offline   Reply With Quote
Old 12-27-2019, 03:03 PM   #344
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Located the front axle for test fit.
Attached Images
   
fishnixon is offline   Reply With Quote
Old 12-27-2019, 03:11 PM   #345
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Looks like I have the shackles going in the right direction, but I have to lengthen them for more clearance. I am thinking about 1 inch. These shackles are from LMC. If I put the shackle mount to the bottom of the frame, I would be done. Well, someone reading this won’t make the same choice “regarding its vertical position” when using a donor frame component, hopefully. I am glad I used the donor frame and shackle mount.
Attached Images
    

Last edited by fishnixon; 12-28-2019 at 10:24 AM.
fishnixon is offline   Reply With Quote
Old 12-27-2019, 03:13 PM   #346
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Overall, I am happy with the progress, and am looking forward to the next steps.
Attached Images
 
fishnixon is offline   Reply With Quote
Old 12-28-2019, 07:51 PM   #347
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Spent time remedying my rear shackle situation. Here’s the test fit. The original distance center to center was about 4”. My new ones are 5” at the centers. Now the leaf spring should be approximately at factory settings. I certainly feel better about having some space in there at the bottom of the frame.
Attached Images
 
fishnixon is offline   Reply With Quote
Old 12-28-2019, 07:56 PM   #348
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Because the original shackles had an embossed area on them, presumably for strength, I added a bead of weld for the same purpose.

Next step is to weld the frame, paint and then hang the leaf springs for good...hopefully.
Attached Images
 

Last edited by fishnixon; 12-28-2019 at 09:09 PM.
fishnixon is offline   Reply With Quote
Old 12-28-2019, 09:29 PM   #349
72 tigger
Registered User
 
72 tigger's Avatar
 
Join Date: Apr 2008
Location: Berne IN
Posts: 3,250
Re: Dumptruck Dolly

Looks really good
__________________
71 C10
72 K20
72 K10 Super
Kirk
72 tigger is offline   Reply With Quote
Old 12-28-2019, 11:31 PM   #350
fishnixon
Registered User
 
fishnixon's Avatar
 
Join Date: Sep 2006
Location: Ely, Minnesota
Posts: 543
Re: Dumptruck Dolly

Quote:
Originally Posted by 72 tigger View Post
Looks really good
Thanks...I am glad my hiccup with the shackle was short lived.
fishnixon is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:56 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com