![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Nov 2014
Location: Virginia Beach, Virginia
Posts: 83
|
Re: Under bed gas tank with side feed?
Jim Carter has reproduction Suburban tanks. Maybe that would work.
https://oldchevytrucks.com/meg149.html |
![]() |
![]() |
![]() |
#2 | |
Active Member
![]() Join Date: Feb 2022
Location: PLANO, TX
Posts: 132
|
Re: Under bed gas tank with side feed?
Quote:
I want a side fill via drivers fender and I think this will work for me.
__________________
1955.1 GMC 100 RestOMod 1972 T120RV 1967 C200 Trail 90 2014 TRD Quad CAB |
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
here is my gas filler location
|
![]() |
![]() |
![]() |
#4 |
Active Member
![]() Join Date: Feb 2022
Location: PLANO, TX
Posts: 132
|
Re: Under bed gas tank with side feed?
Beautiful!
__________________
1955.1 GMC 100 RestOMod 1972 T120RV 1967 C200 Trail 90 2014 TRD Quad CAB |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
on my 57 I put the filler door on the topof the raer fender behind the wheel. it has to sit far enough out for the door to clear the body when it is opening. i used a filler door from a scrap envoy I had laying arond and bent it to fit the shape of the fender. my tank is a belly tank along the inside of the frame and 1/2 way under the cab so it has a bit of a run to get from the filler to the tank. it works well as far as I can tell when filling with a 5 gallon gas can tipped upside down. no burps, fills quick. the filler entry is inside the fender and is a stock envoy filler which has been shortened a little to fit the hose over the frame. the hose from the filler to the metal filler pipe was just generic fuel hose from the hydraulic shop.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Aug 2016
Location: Hunkered Down
Posts: 1,839
|
Re: Under bed gas tank with side feed?
This placement allows easy filling with little or no spillage if careful. It also allows the nozzle to rest away from fender, bed and rear bedpost while filling. No its not touching post but resting on edge of brake light support. I use a vented locking cap which also works well.
Last edited by vintovka; 08-06-2024 at 05:58 PM. |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,503
|
Re: Under bed gas tank with side feed?
I was thinking of cutting the area around the filler neck in the cab out of a junk cab and welding it into the fender to use the stock grommet on the fender. Make it look like that is where it was when the truck left the factory .
__________________
Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around. |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
here are a couple better pics of my schlomozle. it took a bit to get the original cut out surround bent correctly and then the door bent correctly but it fits pretty well now, opens without the door hitting the box rail and is spring loaded so it stays closed. rubber bumpers are from a 2015 silverado, its my daily driver so I looked at that and figured those bumpers would work well. drilled a couple holes and pushed them in.
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
here is the step by step. I did it, you can too. it doesn't have to be in the same spot, the process is the same. cut the area around a fuel door from a donor, trim it so it has a small flange to weld to, cut the hole in the fender where you want the door, bend the door surround and the door so it fits the contour of the body nicely from the backside of the fender, cleco it in place or use self drilling sheet metal screws (teck screws), then tack weld it in place, fit as you go to achieve a good fit and test the door periodically to ensure it opens and closes correctly. keep tacking until the spots are about an inch apart, ensuring not to heat the parts up-you need to take time-use compressed air to cool the parts-dont tack again until the parts are cool enough you COULD put your tongue on it without getting seared, then start tacking about 4 tacks in a row so each tack starts on the last tack and makes a continuous weld as you go. keep cooling the parts off, soon you are done and can grind the area smooth and do the final metal finishing
|
![]() |
![]() |
![]() |
#10 | |
Registered User
Join Date: Mar 2022
Location: Surrey BC
Posts: 804
|
Re: Under bed gas tank with side feed?
nice work dsraven!
Quote:
here was the first test fit |
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
mr48, I think you forgot to add the pics. thats my usual trick, lol.
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,026
|
Re: Under bed gas tank with side feed?
that does the trick too. a little metalworking isn't that tough once you set your mind to it.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|