|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-21-2015, 11:39 PM
|
#26 |
|
Registered User
Join Date: Nov 2014
Location: henderson nc
Posts: 6
|
Re: 22" factory GM transport wheels
55 Chevy truck caps on my 22's before paint.
|
|
|
|
02-05-2015, 03:26 PM
|
#27 |
|
C10 Collector
Join Date: Oct 2003
Location: Baton Rouge, LA
Posts: 417
|
Re: 22" factory GM transport wheels
I figure I'd document my 22's here. on my 67 GMC I was running 1.25" spacers on the rear and .5" up front with drum brakes. I went to the longer dorman studs all the way round. Since 2 studs sheared on my rear spacers I'm ditching them and reversing the wheels. Originally I was going to just change the offset but the hoop has a slight taper and the center gets loose when you slide it back. The steps on the lip also look terrible. So I reversed them with a 4.375" backspace. You could probably get down to 3", maybe a little less backspace if wanted. I'm going to turn the axle nubs down in my lathe to fit the center bore of the wheels and rock them with no spacers and 67 caps. For those wondering, I made a jig with a 2002 Truck front hub to spin the wheel and measure runout. Make sure you measure runout before you seperate the pieces and label the hoop. Oh, and I'm repainting them a light brown.
__________________
///Ryan 1972 Chevy C-10-Bagged, Blown LT1, 700r4, Suicide Doors 1967 GMC- SC & Cam'd 4.8, built 4l80, 3200 stall, posi, 4.10 1967 Chevy LWB- 454 and patina 1971 Blazer - Rusty 1968 Crewcab project Last edited by Bagd72Chevy; 02-05-2015 at 03:37 PM. |
|
|
|
|
08-24-2015, 04:59 PM
|
#28 |
|
Registered User
Join Date: Feb 2013
Location: Dauphin, Manitoba
Posts: 4
|
Re: 22" factory GM transport wheels
How did you make out reversing these?
|
|
|
|
|
08-24-2015, 05:07 PM
|
#29 | |
|
C10 Collector
Join Date: Oct 2003
Location: Baton Rouge, LA
Posts: 417
|
Re: 22" factory GM transport wheels
Quote:
__________________
///Ryan 1972 Chevy C-10-Bagged, Blown LT1, 700r4, Suicide Doors 1967 GMC- SC & Cam'd 4.8, built 4l80, 3200 stall, posi, 4.10 1967 Chevy LWB- 454 and patina 1971 Blazer - Rusty 1968 Crewcab project |
|
|
|
|
|
08-24-2015, 10:49 PM
|
#30 |
|
Registered User
Join Date: Feb 2013
Location: Dauphin, Manitoba
Posts: 4
|
Re: 22" factory GM transport wheels
Ahh yeah, that looks sweet!! Thinking of doing that to a set I have, was it hard to do? Any chance you have more photos of the procedure? Thanks
Last edited by Travis3688; 08-24-2015 at 10:59 PM. |
|
|
|
|
05-03-2016, 03:47 PM
|
#31 |
|
Registered User
Join Date: Feb 2015
Location: E TOWN Alberta
Posts: 16
|
Re: 22" factory GM transport wheels
Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here
If you need any further assistance with that please contact any Admin for help. Last edited by kcsa75; 05-04-2016 at 12:07 AM. |
|
|
|
|
10-07-2017, 03:56 PM
|
#32 |
|
Registered User
Join Date: Sep 2016
Location: Morganton nc
Posts: 1
|
Re: 22" factory GM transport wheels
How do I know where to put the clips and what's the best way to do it
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
