What did you get done this weekend? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DanoDMano · 12-22-2003, 02:59 AM

I repaired the equipment needed to build (4) 737 wings!!!

In other words I had to work and got nothing done on the truck....

leadfoot067 · 12-22-2003, 03:10 AM

went to the wrecking yard saturday morning....got a dome light lense and the little bulb and wire for lighting up the heater control.....ordered a heater control repair kit and a lighter assembley from LMC...then i removed the bed from my parts truck and sold it....sunday i went and moved my 71 olds cutlass...from one storage to another...its been sitting since 93

...but it fired and drove just like i remember it...realised i really miss driving that car.....then came and worked on the jeep thats taken residence in my garage

...almost finished with it....raked the yard of all the leaves...that was my weekend...

casey · 12-22-2003, 04:00 AM

xmas shopping, I hate the mall, arrrr

67sub · 12-22-2003, 09:48 AM

I took all 3 doors apart and fixed the locks, squared up the radio hole in the dash ( p.o. hacked it up) for Kenwood cd player, wired up the kickdown switch for the trans, adjusted modulator and carburetor, cleaned on '72 disc brake front suspension getting it ready to install and went shopping with the wife.

*Randy70C-10* · 12-22-2003, 10:59 AM

I massaged my wifes box.

superchevy · 12-22-2003, 11:46 AM

I finally got Project Daisycutter's cab and bed dropped off at my buddy's body shop. Spent Saturday stripping the cab all the way down so we can get started on the bodywork and patch panels. Sunday, I worked on my work truck to get ready for the state inspection today; new plugs, oil change and a clean-up of the engine bay as I've been neglecting her of late.
SC

ratrod67 · 12-22-2003, 03:51 PM

Got a couple pics of the Camaro as of yesterday. All the parts should be in on Tuesday.

ratrod67 · 12-22-2003, 03:52 PM

another

Suicide-D · 12-22-2003, 04:01 PM

I moved my cab and all my stuff to my shop, because I'm moving into an apartment.

I welded on my buddy's cougar (back window area)

and I put bigger casters on my engine run/test stand, so I can get the engine hoist to roll under it. I still need to finish putting the guages and the radiator support on it.. but it is alot closer.

Mike Culpepper · 12-22-2003, 04:38 PM

FINALLY, got time to replace dist. cap/rotor/module(had truck about 8 months!), I'm amazed that the truck was running at ALL! The HEI brush/spring thing fell out of the cap, there was MAJOR burning and scarring of the under side of the cap. The truck runs alot smother and with more power now. Wonder what else was neglected on this truck?
Mike

Mixup · 12-22-2003, 04:43 PM

Got the old seat out. Welded up some holes started putting Dynamat down before new carpet and seat go in.

Stout72 · 12-22-2003, 04:52 PM

Replaced both window regulators and all of the window fuzzies. Its so nice to be able to roll up the window now, no rattles and no (very few?) leaks.

kevin's 4X4 · 12-22-2003, 05:56 PM

We got all the bearings and brake acc. ordered for the front and rear axles on the 72. Fixed the heater on the 71, and kicked the tires !

70short · 12-22-2003, 06:12 PM

BEEEEEEEEEER!!!!!!!!!!!!!!!!

Martin64 · 12-22-2003, 10:46 PM

I dropped the stock exhaust and got the headers in today. Tomorrow will I'll finish it off and get the rest of the exhaust done....since I'm on vacation everyday is Saturday until Sunday the 4th....

GMC JUNKIE TOO · 12-22-2003, 10:58 PM

I finished the disc brake swap on my friends 57 belair then, I got to drive it

Dident do anything to my truck except drive it. And went to see bad santa

Oh it was in the 60's all weekend.

**PICKMUP** · 12-23-2003, 01:04 AM

You guys are so lucky! I never get to work on my own stuff----too busy getting parts ready for everyone else.
Nice looking BB PS, brackets & pulleys on that engine TXFIREFIGHTER

onetoncrewcab · 12-23-2003, 01:30 AM

I got to do Honey-Do projects. You know the ones. Honey do this. Honey do that.
MJ

12-22-2003, 02:59 AM	#26
DanoDMano Pronounced "Pew-al-up" Join Date: Oct 2002 Location: Puyallup, Washington Posts: 845	I repaired the equipment needed to build (4) 737 wings!!! In other words I had to work and got nothing done on the truck.... __________________ Classic GM Trucks of Washington Club Member 1970 FS chevy,350/350, Edelbrock cam and intake. Holley 650 carb,HEI,AT,Tangier Orange, 18's, Power Locks, Truck Photos

12-22-2003, 03:10 AM	#27
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	went to the wrecking yard saturday morning....got a dome light lense and the little bulb and wire for lighting up the heater control.....ordered a heater control repair kit and a lighter assembley from LMC...then i removed the bed from my parts truck and sold it....sunday i went and moved my 71 olds cutlass...from one storage to another...its been sitting since 93 ...but it fired and drove just like i remember it...realised i really miss driving that car.....then came and worked on the jeep thats taken residence in my garage ...almost finished with it....raked the yard of all the leaves...that was my weekend... __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

12-22-2003, 09:48 AM	#29
67sub Registered User Join Date: Aug 2003 Location: D/FW TX Posts: 430	I took all 3 doors apart and fixed the locks, squared up the radio hole in the dash ( p.o. hacked it up) for Kenwood cd player, wired up the kickdown switch for the trans, adjusted modulator and carburetor, cleaned on '72 disc brake front suspension getting it ready to install and went shopping with the wife. __________________ 2004 Kawasaki KLR Always looking for a cheap driver

12-22-2003, 11:46 AM	#31
superchevy Got big-block? Join Date: Jul 2000 Location: Austin, Texas Posts: 2,453	I finally got Project Daisycutter's cab and bed dropped off at my buddy's body shop. Spent Saturday stripping the cab all the way down so we can get started on the bodywork and patch panels. Sunday, I worked on my work truck to get ready for the state inspection today; new plugs, oil change and a clean-up of the engine bay as I've been neglecting her of late. SC __________________ '68 CST SWB factory 396/T400 buddy buckets, a/c, ps, pb '72 Corvette convertible 454/4spd/ac, ps, pb '73 GMC Sierra Grande short wide 454/T400 ps, pb, ac '77 K5 Blazer black on red, 350/T350/NP205 ps, pb, ac all original '78 GMC Sierra Classic short wide 454/T400 ps, pb, ac '72 GMC Sprint SP454. 1 of 38 built. '73 GMC Sprint SP454. 1 of 71 built. '75 GMC Sprint SP454. 1 of 25 built. SOLD! '72 GMC K25 4x4 468/4L80e/NP205 build thread http://67-72chevytrucks.com/vboard/s...23#post4324423 SOLD!'55 Chevy gasser 496/4spd build thread http://67-72chevytrucks.com/vboard/s...96#post4324396

12-22-2003, 03:51 PM	#32
ratrod67 Registered User Join Date: Sep 2002 Location: DFW Texas Posts: 2,270	Got a couple pics of the Camaro as of yesterday. All the parts should be in on Tuesday. Attached Images

12-22-2003, 04:00 AM	#28
casey Registered User Join Date: Jan 2003 Location: Kelowna B.C. Canada Posts: 2,048	xmas shopping, I hate the mall, arrrr

12-22-2003, 10:59 AM	#30
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	I massaged my wifes box.

12-22-2003, 03:52 PM	#33
ratrod67 Registered User Join Date: Sep 2002 Location: DFW Texas Posts: 2,270	another Attached Images

12-22-2003, 04:01 PM	#34
Suicide-D Registered User Join Date: Jan 2001 Location: Katy, TX...but the love of my life resides in Dublin,OH. Posts: 1,408	let's see.... I moved my cab and all my stuff to my shop, because I'm moving into an apartment. I welded on my buddy's cougar (back window area) and I put bigger casters on my engine run/test stand, so I can get the engine hoist to roll under it. I still need to finish putting the guages and the radiator support on it.. but it is alot closer. Attached Images

12-22-2003, 04:38 PM	#35
Mike Culpepper Red Join Date: Feb 2003 Location: Llano... Texas Hill Country Posts: 448	FINALLY, got time to replace dist. cap/rotor/module(had truck about 8 months!), I'm amazed that the truck was running at ALL! The HEI brush/spring thing fell out of the cap, there was MAJOR burning and scarring of the under side of the cap. The truck runs alot smother and with more power now. Wonder what else was neglected on this truck? Mike __________________ '72 Cheyenne LWB 350/350 "The sun don't shine on the same dog's ass all the time." - Catfish Hunter (commenting on why he was not able to pitch another perfect game).

12-22-2003, 04:43 PM	#36
Mixup Registered User Join Date: Jan 2002 Location: Henderson, NV Posts: 358	Got the old seat out. Welded up some holes started putting Dynamat down before new carpet and seat go in. __________________ 1980 Chevy Shortbed Pickup 1969 Z28 engine Turbo 350

12-22-2003, 04:52 PM	#37
Stout72 Not my good side. Join Date: Mar 2002 Location: Fairfield, California Posts: 222	Replaced both window regulators and all of the window fuzzies. Its so nice to be able to roll up the window now, no rattles and no (very few?) leaks. __________________ 72 Chevy K20 Custom Camper, 350/350, 4" lift, dual shock suspension front & rear. Daily driver and a work in progress. 00 Suburban LT 90 Camaro RS 79 Yamaha XS1100 Special (Ol' Reliable)

12-22-2003, 05:56 PM	#38
kevin's 4X4 Registered User Join Date: Jun 2003 Location: hollister ca Posts: 101	We got all the bearings and brake acc. ordered for the front and rear axles on the 72. Fixed the heater on the 71, and kicked the tires ! __________________ FYI : Kevin's 4x4 is also know as landon4421 ! The boy wants an avatar !

12-22-2003, 06:12 PM	#39
70short Registered User Join Date: Sep 2003 Location: Boise ID Posts: 609	BEEEEEEEEEER!!!!!!!!!!!!!!!! __________________ "72" Red CORVETTE 4-speed 350 "70" Chevy Short Bed early stages of resto. Edel 600 cfm carb Weiand Stealth Intake HEI shorty Headers 4/2 Drop 295 50R 15 TOYO on 10 inch wide corvette rally rims at all 4 corners. "CHEVY RULES"

12-22-2003, 10:46 PM	#40
Martin64 Registered User Join Date: Oct 2003 Location: Yuma, Az Posts: 477	I dropped the stock exhaust and got the headers in today. Tomorrow will I'll finish it off and get the rest of the exhaust done....since I'm on vacation everyday is Saturday until Sunday the 4th.... __________________ Martin Gibson USAF Retired 1964(-ish) C10



Register or Log In To remove these advertisements.

12-22-2003, 10:58 PM	#41
GMC JUNKIE TOO THE QUICKER FIXERUPER Join Date: Jul 2002 Location: Ok Posts: 615	I finished the disc brake swap on my friends 57 belair then, I got to drive it Dident do anything to my truck except drive it. And went to see bad santa Oh it was in the 60's all weekend.

12-23-2003, 01:04 AM	#42
PICKMUP "Trucks with Class" Join Date: Jul 2000 Location: OLYMPIA, WA, USA Posts: 8,130	You guys are so lucky! I never get to work on my own stuff----too busy getting parts ready for everyone else. Nice looking BB PS, brackets & pulleys on that engine TXFIREFIGHTER __________________ Email: frankeham@comcast.net Phone: 360-956-7170

12-23-2003, 01:30 AM	#43
onetoncrewcab One of my kids. Cute eh? Join Date: Oct 2001 Location: Mitchell, SD Posts: 1,286	I got to do Honey-Do projects. You know the ones. Honey do this. Honey do that. MJ __________________ If a kid asks where rain comes from, I think a cute thing to tell him is “God is crying.” And if he asks why God is crying, another cute thing to tell him is “Probably because of something you did. John 3:16 2006 Chevy HHR 2000 Dodge Durango 1985 Jeep CJ-7 1970 Chevy Pickup

Register or Log In To remove these advertisements.