1972 C/20 Truck parting out - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

gcburdic · 06-03-2009, 12:15 PM

Quote:

Originally Posted by RPOZ11

HEI was not available on these models until later years, maybe 75.
Any wiring for an electronic choke would either have to be manually fabricated, or...
Have a reproduction/refurbished system wired to accomplish that!
I usually select a switched 12 Volt supply that is fused to the electronic choke when used.
When using an HEI in these, take particular NOTICE to the wire that you are using to supply that 12-Volt source.
Using a lesser amperage wire may cause either hazardous electrical fires and/or ignition failure.
The electrical demand to operate an HEI is significantly higher than a points system!

Thanks for your explaination....I guess I realized that I didn't ask the right question....do you have any wiring harnesses available??...I think he plans on rewiring them to be HEI.....does that make sense?...Thanks

**RPOZ11** · 06-04-2009, 02:05 AM

Quote:

Originally Posted by paul mora

I live in in Orange county so I can pick up or you can deliver what condition are they in and how much for the all or part . Yo can give me a call at 714 3238376

I AM in the OC!

Just let me know!

**RPOZ11** · 06-04-2009, 02:08 AM

Quote:

Originally Posted by gcburdic

Thanks for your explaination....I guess I realized that I didn't ask the right question....do you have any wiring harnesses available??...I think he plans on rewiring them to be HEI.....does that make sense?...Thanks

I do not have the aftermarket wiring that you need.

Its a matter of increasing the wire diameter to accept the Amperage demands.

It is available.

Try the aftermarket people who do that.

M&H is start!

**RPOZ11** · 06-04-2009, 02:09 AM

Quote:

Originally Posted by D.PASSMORE

Do you have both camper mirrors? Intrested.

Sorry both were not worth keeping.

I replaced these with another set.

**paul mora** · 06-05-2009, 09:31 AM

I am not clear if you have the door panels and the condition of the seat. How do we set up a time to see the parts you can call me at 714 323 8376

**RPOZ11** · 06-05-2009, 09:42 AM

Quote:

Originally Posted by paul mora

I am not clear if you have the door panels and the condition of the seat. How do we set up a time to see the parts you can call me at 714 323 8376

PM sent

sleepertruck72 · 06-05-2009, 03:43 PM

pm sent

**RPOZ11** · 06-06-2009, 10:31 AM

I got your messages and replied to both.

Ill be back later this afternoon.

*mrhino* · 06-07-2009, 06:46 AM

im looking for some upper trim molding what do you have?

olblue60@aol.com · 06-07-2009, 06:48 AM

Do you have any of the windshield stainless? Thanks

John

**RPOZ11** · 06-07-2009, 01:37 PM

Quote:

Originally Posted by olblue60@aol.com

Do you have any of the windshield stainless? Thanks

John

Sorry I dont.

cxune · 06-07-2009, 08:46 PM

I didn't spot this in your photos, but in all that stuff do you happen to have an alternator pulley? If so, how much shipped to 77007?

Thanks!
Patrick

**RPOZ11** · 06-07-2009, 09:38 PM

Quote:

Originally Posted by cxune

I didn't spot this in your photos, but in all that stuff do you happen to have an alternator pulley? If so, how much shipped to 77007?

Thanks!
Patrick

I have Alt cores laying around.

I assume you just need a standard alt pulley.

**RPOZ11** · 06-07-2009, 09:40 PM

Quote:

Originally Posted by mrhino

im looking for some upper trim molding what do you have?

Honestly none are worth trying to save.

Even the one on the fender you see in the bed of my other truck is bent.

I was just going to go with a solid color and disregard the moulding because of this had I put this one together.

cxune · 06-08-2009, 08:57 AM

Yeah, I just need the pulley for a v-belt. When I buy single wire alternators they always seem to come with a serpentine type pulley.

Dano69c10 · 06-10-2009, 11:19 PM

Will you sell the rolling frame? If you are how much?

**RPOZ11** · 06-11-2009, 01:29 AM

Quote:

Originally Posted by Dano69c10

Will you sell the rolling frame? If you are how much?

Yes, PM sent.

**paul mora** · 06-18-2009, 09:29 AM

Your are a tough person to get in touch with. I tried to reach you last weekend will you be around Saturday so I can come by and have a look and at the seat door panels and bumper

budnikguy · 06-18-2009, 10:54 AM

Put me in line for the seat and possible door panels...

Special Greg · 06-18-2009, 07:53 PM

I was wondering if the mirrors were available. Thanks

06-05-2009, 09:31 AM	#30
paul mora Senior Member Join Date: Jan 2009 Location: huntington beach california Posts: 976	Re: 1972 C/20 Truck parting out I am not clear if you have the door panels and the condition of the seat. How do we set up a time to see the parts you can call me at 714 323 8376

06-05-2009, 03:43 PM	#32
sleepertruck72 Registered User Join Date: Nov 2007 Location: Turlock California 95380 Posts: 2,075	Re: 1972 C/20 Truck parting out pm sent __________________ 72 C20 Longbed 05 1500 Z71

06-06-2009, 10:31 AM	#33
RPOZ11 72 BB C30 Super LongHorn Join Date: Nov 2002 Location: Chavez Ravine Posts: 1,606	Re: 1972 C/20 Truck parting out I got your messages and replied to both. Ill be back later this afternoon. __________________ 72 BB C/30 Longhorn Super HO72 No-Spin, #'s matching, Tilt, Tach, AC, AM/FM HO72 build : http://67-72chevytrucks.com/vboard/s...d.php?t=714492 2017 SS

06-07-2009, 06:46 AM	#34
mrhino Account Suspended Join Date: Aug 2007 Location: USA Posts: 1,223	Re: 1972 C/20 Truck parting out im looking for some upper trim molding what do you have?

06-07-2009, 06:48 AM	#35
olblue60@aol.com member Join Date: Dec 2003 Location: Silver Spring Md.20901 Posts: 2,031	Re: 1972 C/20 Truck parting out Do you have any of the windshield stainless? Thanks John __________________ 1967 C/K10 Chevy Panel 1968 C/K20 Chevy Pickup 1968 C/K10 Chevy Suburban 1941 Chevy Sedan Delivery 1960 Chevy Sedan Delivery 1972 Camaro SS 396 #s matching 1971 Harley FX Superglide

06-07-2009, 08:46 PM	#37
cxune Registered User Join Date: Aug 2003 Location: Houston, Texas Posts: 68	Re: 1972 C/20 Truck parting out I didn't spot this in your photos, but in all that stuff do you happen to have an alternator pulley? If so, how much shipped to 77007? Thanks! Patrick

06-08-2009, 08:57 AM	#40
cxune Registered User Join Date: Aug 2003 Location: Houston, Texas Posts: 68	Re: 1972 C/20 Truck parting out Yeah, I just need the pulley for a v-belt. When I buy single wire alternators they always seem to come with a serpentine type pulley.

06-10-2009, 11:19 PM	#41
Dano69c10 Senior Member Join Date: Jan 2005 Location: Ontario, Kali Posts: 2,427	Re: 1972 C/20 Truck parting out Will you sell the rolling frame? If you are how much? __________________ '69 Fleet It ain't yours, if you didn't build it!

06-18-2009, 09:29 AM	#43
paul mora Senior Member Join Date: Jan 2009 Location: huntington beach california Posts: 976	Re: 1972 C/20 Truck parting out Your are a tough person to get in touch with. I tried to reach you last weekend will you be around Saturday so I can come by and have a look and at the seat door panels and bumper

06-18-2009, 10:54 AM	#44
budnikguy Registered User Join Date: Sep 2007 Location: Riverside, CA Posts: 4,316	Re: 1972 C/20 Truck parting out Put me in line for the seat and possible door panels...

06-18-2009, 07:53 PM	#45
Special Greg Registered User Join Date: Mar 2008 Location: Fort Collins Colorado Posts: 13	Re: 1972 C/20 Truck parting out I was wondering if the mirrors were available. Thanks



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.