63-87 rack and pinion - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**robnolimit** · 06-14-2011, 07:13 PM

You can see the upper shaft connecting to the column and top u-joint.

**robnolimit** · 06-14-2011, 07:15 PM

Using factory G.M. lines, we plumbed the power steering hoses.

jake696 · 06-14-2011, 07:25 PM

This looks better than my wife's rack. Heres my credit card number
4756 9693 1245 1965 ex 01/65 . Just kidding looks awsome .

gringoloco · 06-14-2011, 07:55 PM

SEKSEE! How much clearance between TREs and framerails? I.e: how much can you section the crossmember before you have clearance issues? Looks nice

**robnolimit** · 06-15-2011, 07:12 PM

Our 72 JT is running this. We raised the crossmember 1 1/2". And there is no need to 'C' for TRE clearance. When this install is done, I'll measure it for you, this will have all of the production parts on it. Should be done on friday.

**robnolimit** · 06-17-2011, 02:08 PM

Here's the last steps. We finally recieved the adjuster sleeves today! The hex shock is threaded with 5/8" x 18 on one side, and 14mm x 1.5 on the other. We then had them heat treated. Tie rod ends are high-mis-alignment 5/8" chromoly.

lownbad71 · 06-20-2011, 01:41 AM

What is the latest on this install? Any idea what it is going to cost?

**robnolimit** · 06-20-2011, 02:42 PM

Sorry about that... power went down, couldn't get to the pictures

Here you go............
Step 2
Start by removing the spring clamps on the rack boots

**robnolimit** · 06-20-2011, 02:51 PM

Thread the rod end into the adjuster sleeve. Leave approx 1/4" of thread showing, tighten the jam nut - TIGHT!

**robnolimit** · 06-20-2011, 02:53 PM

** Thread the adjuster sleeve onto the inner tie-rod end. Leave approx 1" of thread showing. Leave the JAM NUT Loose

**robnolimit** · 06-20-2011, 02:58 PM

Bolt the new tie-rod assembly to the bottom of the steering arm. The large U.S.S. washer installs on the bottom, as a saftey stop for the rod end.

**robnolimit** · 06-20-2011, 02:59 PM

The Complete Install. Toe adjustment is made between the inner tie-rod end and the adjuster sleeve. Don't forget to put the spring clamp back on for the rack boot. For smooth cruisers, set toe at - 1/8" . For more spirited driving, try 1/8" toe out.

68GMCCustom · 06-20-2011, 05:27 PM

just what I've been waiting and looking for.....now just need to dig up the scratch to pay for it....

Custom 68 · 06-22-2011, 11:19 AM

very nice product and write up Rob, glad it is coming together.

65Short · 07-02-2011, 04:10 PM

Quote:

Originally Posted by robnolimit

Our 72 JT is running this. We raised the crossmember 1 1/2". And there is no need to 'C' for TRE clearance. When this install is done, I'll measure it for you, this will have all of the production parts on it. Should be done on friday.

Any way we can get pics of this? Did you section the crossmember or Z the frame? Thanks, Jon.

Jenkins Classics · 07-04-2011, 01:25 AM

How much is the kit and when will it be available.

Slammed50 · 07-19-2011, 05:34 PM

What kind of rack and pinion are you using for this set up? Looks great, just what I am looking to upgrade next on my truck.
Posted via Mobile Device

doubleRdazz · 07-19-2011, 06:01 PM

Whats the price?
Posted via Mobile Device

**rob32472** · 07-20-2011, 07:44 AM

http://67-72chevytrucks.com/vboard/s...d.php?t=441047 check out this thread it will tell you guys what you need to know

mac · 09-18-2011, 09:28 AM

Rob- any movement on the "isolator" delivery?

**robnolimit** · 11-17-2011, 12:38 PM

All the parts are in, and all current orders have shipped. Thanks for the patience. We're all really happy with how this turned out. Hopefully our extra work will provide many truckers with years of happy cruising. Now, how long will it take the others to copy??

SBTork · 11-18-2011, 06:50 PM

Quote:

Originally Posted by robnolimit

All the parts are in, and all current orders have shipped. Thanks for the patience. We're all really happy with how this turned out. Hopefully our extra work will provide many truckers with years of happy cruising. Now, how long will it take the others to copy??

I am curious about this too. It will happen, I am sure someone will copy this. It's too bad, but I am sure it will happen.

On the plus side, you guys did an awesome job and are offering a great product, so kudos

**robnolimit** · 11-18-2011, 09:38 PM

Thanks. I know it will happen too. I hope that joking about it ahead of time will put the copiers on notice that we know they are .... can't say that word here.

DUTCHMAN · 12-16-2011, 07:30 AM

Hi Rob, I'm not such a gearhead but trying to understand all the info here on the board.

I'm wondering what are the benefits from your rack and pinion vs my oem power steering? Does it handle better and has it a shorter turning ratio?

thanks

rs72z · 12-31-2011, 06:44 AM

Anyone know what the price is on this setup? I didnt see it on their web site.

06-14-2011, 07:13 PM	#51
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion You can see the upper shaft connecting to the column and top u-joint. Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-14-2011, 07:15 PM	#52
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Using factory G.M. lines, we plumbed the power steering hoses. Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-14-2011, 07:25 PM	#53
jake696 Registered User Join Date: Jun 2011 Location: highland ca Posts: 4	Re: 63-87 rack and pinion This looks better than my wife's rack. Heres my credit card number 4756 9693 1245 1965 ex 01/65 . Just kidding looks awsome .

06-14-2011, 07:55 PM	#54
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: 63-87 rack and pinion SEKSEE! How much clearance between TREs and framerails? I.e: how much can you section the crossmember before you have clearance issues? Looks nice __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

06-15-2011, 07:12 PM	#55
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Our 72 JT is running this. We raised the crossmember 1 1/2". And there is no need to 'C' for TRE clearance. When this install is done, I'll measure it for you, this will have all of the production parts on it. Should be done on friday. __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-17-2011, 02:08 PM	#56
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Here's the last steps. We finally recieved the adjuster sleeves today! The hex shock is threaded with 5/8" x 18 on one side, and 14mm x 1.5 on the other. We then had them heat treated. Tie rod ends are high-mis-alignment 5/8" chromoly. Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-20-2011, 01:41 AM	#57
lownbad71 Registered User Join Date: Oct 2007 Location: folsom Posts: 19	Re: 63-87 rack and pinion What is the latest on this install? Any idea what it is going to cost?

06-20-2011, 02:42 PM	#58
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Sorry about that... power went down, couldn't get to the pictures Here you go............ Step 2 Start by removing the spring clamps on the rack boots Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-20-2011, 02:51 PM	#59
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Thread the rod end into the adjuster sleeve. Leave approx 1/4" of thread showing, tighten the jam nut - TIGHT! Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-20-2011, 02:53 PM	#60
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Thread the adjuster sleeve onto the inner tie-rod end. Leave approx 1" of thread showing. Leave the JAM NUT Loose Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion** Proud to put our products up against all others!

06-20-2011, 02:58 PM	#61
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Bolt the new tie-rod assembly to the bottom of the steering arm. The large U.S.S. washer installs on the bottom, as a saftey stop for the rod end. Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-20-2011, 02:59 PM	#62
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion The Complete Install. Toe adjustment is made between the inner tie-rod end and the adjuster sleeve. Don't forget to put the spring clamp back on for the rack boot. For smooth cruisers, set toe at - 1/8" . For more spirited driving, try 1/8" toe out. Attached Images __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

06-20-2011, 05:27 PM	#63
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: 63-87 rack and pinion just what I've been waiting and looking for.....now just need to dig up the scratch to pay for it.... __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

06-22-2011, 11:19 AM	#64
Custom 68 Registered User Join Date: Nov 2001 Location: Springfield, MO Posts: 2,937	Re: 63-87 rack and pinion very nice product and write up Rob, glad it is coming together. __________________ Dave 1968 Custom Chevy with turbo charged 5.3 gen III 4l80e swap 1967-71 GMC 3/4 ton long step 4x4 (not sure what year exactly?) "A good friend will bail you out of jail...but a true friend will be sitting next to you saying "that was frekin awesome". "If it doesn't fit force it...If it breaks then it needed to be replaced anyway!"

07-04-2011, 01:25 AM	#66
Jenkins Classics Registered User Join Date: Jul 2011 Location: Hendersonville,TN. Posts: 11	Re: 63-87 rack and pinion How much is the kit and when will it be available.



Register or Log In To remove these advertisements.

07-19-2011, 05:34 PM	#67
Slammed50 Registered User Join Date: Apr 2011 Location: Albuquerque, NW Posts: 121	Re: 63-87 rack and pinion What kind of rack and pinion are you using for this set up? Looks great, just what I am looking to upgrade next on my truck. Posted via Mobile Device

07-19-2011, 06:01 PM	#68
doubleRdazz Registered User Join Date: May 2011 Location: jersey Posts: 42	Re: 63-87 rack and pinion Whats the price? Posted via Mobile Device

07-20-2011, 07:44 AM	#69
rob32472 Registered User Join Date: May 2007 Location: dallas ga Posts: 1,505	Re: 63-87 rack and pinion http://67-72chevytrucks.com/vboard/s...d.php?t=441047 check out this thread it will tell you guys what you need to know

09-18-2011, 09:28 AM	#70
mac Active Member Join Date: Jan 2005 Location: Spokane WA Posts: 166	Re: 63-87 rack and pinion Rob- any movement on the "isolator" delivery?

11-17-2011, 12:38 PM	#71
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion All the parts are in, and all current orders have shipped. Thanks for the patience. We're all really happy with how this turned out. Hopefully our extra work will provide many truckers with years of happy cruising. Now, how long will it take the others to copy?? __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

11-18-2011, 09:38 PM	#73
robnolimit Senior Member Join Date: Jul 2010 Location: Dandridge, Tn. USA Posts: 2,226	Re: 63-87 rack and pinion Thanks. I know it will happen too. I hope that joking about it ahead of time will put the copiers on notice that we know they are .... can't say that word here. __________________ GoodGuys 2012 Pro-Truck Champion 2012 Truckin' Throwdown Champion GoodGuys 2011 National Champion 2011 Truckin' Throwdown Champion GoodGuys 2010 National Champion Proud to put our products up against all others!

12-16-2011, 07:30 AM	#74
DUTCHMAN Registered User Join Date: Dec 1999 Location: the Netherlands Posts: 363	Re: 63-87 rack and pinion Hi Rob, I'm not such a gearhead but trying to understand all the info here on the board. I'm wondering what are the benefits from your rack and pinion vs my oem power steering? Does it handle better and has it a shorter turning ratio? thanks __________________ 06 BMW 330d aut touring full option 83 Jeep CJ7 360 aut sold 71 GMC Suburban 67 Chevrolet C10 stepside 54 Ford F100 sold 49 Chevrolet coe 48 Ford f6 coe Strijen the Netherlands "NO MISTAKES NO PROGRESS"

12-31-2011, 06:44 AM	#75
rs72z Registered User Join Date: Oct 2011 Location: Emory TX Posts: 900	Re: 63-87 rack and pinion Anyone know what the price is on this setup? I didnt see it on their web site.

Register or Log In To remove these advertisements.