** YOUNG FRANKENSTEIN ** The truck Chevrolet should have built. - Page 30 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

drewskiren · 03-02-2011, 10:32 PM

Quote:

Originally Posted by Palf70Step

Why not use the stock Vortec muffler from 96-up dual in and single out. Fairly efficient and mellow

Quote:

Originally Posted by 68 TT

Along the same lines, why not go with a stock 2002 truck muffler since you have that theme going already.

Off the shelf replacement mufflers should give you some choice of sound level and they will all be relatively the same size so swapping one for another will be a piece of cake.

You probably have a stock one or two sitting around that you can build the exhaust system around to get you started.

I am moving in this direction, glad to hear ya'll agree. I was investigating sounds of the 2 trucks that I have with the stock setup. The 6.0 Denali vs. 5.3 is significant. The 6.0 definitely has a little burble and the 5.3 does not. A quick look underneath revealed the the 6.0 muffler is different - soooo, since I have a complete 6.0 exhaust system from a Yukon with the dual inlet muffler like I listened to - I'll be scrapping what I did last night. No biggie since I only spent an hour on it. I'll get that system loose this weekend and delete the cats on it again. The muffler is dual in - dual out, but on a Yukon it converges into 1 right after the exit. I wonder what it sounds like separate vs. merged?

pickup67man · 03-02-2011, 11:25 PM

Like your idea of 4 link in rear. I want to use a newer chassis for my suburban also and the wheelbase will be different no matter what I use (stock is 127"). That makes the change in wheelbase easier with the good ride.

drewskiren · 03-03-2011, 12:18 AM

Quote:

Originally Posted by pickup67man

Like your idea of 4 link in rear. I want to use a newer chassis for my suburban also and the wheelbase will be different no matter what I use (stock is 127"). That makes the change in wheelbase easier with the good ride.

Exactly!

Rokcrln · 03-03-2011, 12:20 AM

On my 5.3L in LowBuk I have stock camaro manifolds with 2.5" duals out to a 3" merge right behind the trans then it goes from their the single pipe goes to the flow master in and out. It is mellow but you can tell their is something under the hood that is not stock.
With that being said I think with your build I would go with a stock set up you have around their and down the road you can swap out for a cat back set up that is made for your truck if you want a change.

Kevin
LFD Inc.

drewskiren · 03-03-2011, 10:00 AM

Quote:

Originally Posted by Rokcrln

On my 5.3L in LowBuk I have stock camaro manifolds with 2.5" duals out to a 3" merge right behind the trans then it goes from their the single pipe goes to the flow master in and out. It is mellow but you can tell their is something under the hood that is not stock.
With that being said I think with your build I would go with a stock set up you have around their and down the road you can swap out for a cat back set up that is made for your truck if you want a change.

Kevin
LFD Inc.

I agree, I've got a free exhaust system, why not use it. I can always change it later when I'm bored with it.

No cats on yours? How does she run??

Does anyone know if you gain much by deleting the cats?

drewskiren · 03-04-2011, 12:13 AM

And now for my next trick.

Name: DRW_6619.jpg
Views: 3920
Size: 46.8 KB

Name: DRW_6620.jpg
Views: 3922
Size: 44.5 KB

Name: DRW_6618.jpg
Views: 3872
Size: 44.7 KB

I am too cheap to buy an aftermarket air system since they are over $1000. I have 3 of these new style units left over, and it is factory engineered ready to plug into my harness. I'll have to make it fit somehow if it kills me.

swamp rat · 03-04-2011, 12:26 AM

Get a shoe horn!

jbclassix · 03-04-2011, 12:58 AM

I just watched despicable me and I think Gru had a tool you need

drewskiren · 03-04-2011, 01:12 AM

Quote:

Originally Posted by jbclassix

I just watched despicable me and I think Gru had a tool you need

Yes, a shrink ray would be quite handy about now.

VA72C10 · 03-04-2011, 02:08 AM

Have you looked at what they run on the used parts market? Maybe you can sell them and pick up a vintage air with the money?

hgs_notes · 03-04-2011, 08:48 AM

You've done some terrific work on this project, but I don't think that unit is going to fit under your dash.

ERASER5 · 03-04-2011, 09:52 AM

Quote:

Originally Posted by drewskiren

Yes, a shrink ray would be quite handy about now.

Yea. Until the unit re-expands after install and tears the truck apart.

I tend to over analize cartoons. It's a sickness.

drewskiren · 03-04-2011, 10:14 AM

Quote:

Originally Posted by VA72C10

Have you looked at what they run on the used parts market? Maybe you can sell them and pick up a vintage air with the money?

These factory AC systems never die and never get smashed in a wreck, so there is no market for them at all - that's why I still have 3.

I think I can, I think I can, I think I can......

**67cheby** · 03-04-2011, 10:26 AM

i dont think you are trying to save money ....i think you just like the challenge of seeing if you can get it in there !!!!! YOU CAN DO IT !!! then you will have pass and driver climate control ...how cool is that

drewskiren · 03-04-2011, 10:49 AM

[quote=67cheby;4529326] I don't think you are trying to save money ....I think you just like the challenge of seeing if you can get it in there !!!!! YOU CAN DO IT !!!

Hmmmmm, I think you may be right.

68 TT · 03-04-2011, 03:26 PM

What about pulling the stock dash off the firewall, fit up the A/C unit then reinstall the stock dash over the top. You could then locate the stock metal dash panel a little farther off the firewall than it was stock to give you the room you need. Some metal filler panels on the dash top and sides will be needed but it can still look stock when you are done, just stretched a little.

drewskiren · 03-04-2011, 03:50 PM

Quote:

Originally Posted by 68 TT

What about pulling the stock dash off the firewall, fit up the A/C unit then reinstall the stock dash over the top. You could then locate the stock metal dash panel a little farther off the firewall than it was stock to give you the room you need. Some metal filler panels on the dash top and sides will be needed but it can still look stock when you are done, just stretched a little.

I like it, sounds like a good fallback plan. Nobody would ever really realize the change I suspect.

propanemudtruck · 03-04-2011, 05:54 PM

As long as the dash isn't in the middle of the doorway....

Much talent in this build, thank you again for sharing!

JasonBird · 03-04-2011, 06:28 PM

lol, i think the back seats just got smaller!! JK ;-)

drewskiren · 03-04-2011, 07:50 PM

Abracadabra

POOF

67chevy1series · 03-04-2011, 07:56 PM

wow that is awsome yes gru did have the tool you needed well i hope it works better than it looks.....that looks kinda ugly... but its ugly because it was kept inside anewer dash.....anyways drew great progress

VA72C10 · 03-04-2011, 08:01 PM

Nice job shoehorning that in

It doesn't stick down that much lower than a stock A/C box actually...probably 3-4" or so more....
...are you going to be able to integrate the controls somehow?

Pop's C-10 · 03-04-2011, 08:17 PM

Nice...who needs a glove box anyway....lol

You running beanch or buckets...

JasonBird · 03-04-2011, 08:23 PM

that is some nice photoshoppin'!!

67chevy1series · 03-04-2011, 08:34 PM

Quote:

Originally Posted by JasonBird

that is some nice photoshoppin'!!

haha

03-02-2011, 11:25 PM	#727
pickup67man Registered User Join Date: Jun 2009 Location: Puyallup, WA Posts: 337	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Like your idea of 4 link in rear. I want to use a newer chassis for my suburban also and the wheelbase will be different no matter what I use (stock is 127"). That makes the change in wheelbase easier with the good ride. __________________ Travis 2005 K2500 Duramax (hauls the junk home) 1967 Chev C10 (hauls a$$) 1970 Suburban (Yukon XL 4 door) 1968 GMC 3/4 ton (sheetmetal only, chassis gone) 2005 Malibu (wife's car, still a Chevy) Project Family Hauler New Home for Chevys (Moved in and working)

03-03-2011, 12:20 AM	#729
Rokcrln Senior Member Join Date: Jul 2005 Location: Winters Ca. 95694 Posts: 4,843	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. On my 5.3L in LowBuk I have stock camaro manifolds with 2.5" duals out to a 3" merge right behind the trans then it goes from their the single pipe goes to the flow master in and out. It is mellow but you can tell their is something under the hood that is not stock. With that being said I think with your build I would go with a stock set up you have around their and down the road you can swap out for a cat back set up that is made for your truck if you want a change. Kevin LFD Inc.

03-04-2011, 12:13 AM	#731
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. And now for my next trick. I am too cheap to buy an aftermarket air system since they are over $1000. I have 3 of these new style units left over, and it is factory engineered ready to plug into my harness. I'll have to make it fit somehow if it kills me. __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife! Last edited by drewskiren; 03-04-2011 at 10:54 AM.

03-04-2011, 12:26 AM	#732
swamp rat Registered User Join Date: Oct 2007 Location: Spanaway Posts: 8,451	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Get a shoe horn! __________________ Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's

03-04-2011, 12:58 AM	#733
jbclassix Junk Yartist Join Date: Jul 2009 Location: Greeley, CO Posts: 2,203	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I just watched despicable me and I think Gru had a tool you need __________________ -Jeremy YOU ONLY FAIL IF YOU STOP TRYING 70 Crew Cab Build Link 70 GMC Suburban 4X4 build thread 95 Yukon Daily Driver Rebuilding an NP205

03-04-2011, 02:08 AM	#735
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Have you looked at what they run on the used parts market? Maybe you can sell them and pick up a vintage air with the money? __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-04-2011, 08:48 AM	#736
hgs_notes GEARHEAD Join Date: Aug 2003 Location: MN Posts: 6,125	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. You've done some terrific work on this project, but I don't think that unit is going to fit under your dash. __________________ If no one knows what you're doing, they can't tell you you're doing it wrong HG's Dream Car Build - Shelby Cobra Kit Build your own adjustable track bar 71 Long Fleet C/10 72 Jimmy 4x4 (Junkyard Jimmy) HG's Plow Truck '78 K35 Dually Bigass Farm Truck HG's thread of miscellaneous stuff

03-04-2011, 10:26 AM	#739
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. i dont think you are trying to save money ....i think you just like the challenge of seeing if you can get it in there !!!!! YOU CAN DO IT !!! then you will have pass and driver climate control ...how cool is that __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-04-2011, 10:49 AM	#740
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. [quote=67cheby;4529326] I don't think you are trying to save money ....I think you just like the challenge of seeing if you can get it in there !!!!! YOU CAN DO IT !!! Hmmmmm, I think you may be right. __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife! Last edited by drewskiren; 03-04-2011 at 11:00 AM.

03-04-2011, 03:26 PM	#741
68 TT Still plays with trucks Join Date: Jul 2009 Location: Spokane, WA Posts: 3,556	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. What about pulling the stock dash off the firewall, fit up the A/C unit then reinstall the stock dash over the top. You could then locate the stock metal dash panel a little farther off the firewall than it was stock to give you the room you need. Some metal filler panels on the dash top and sides will be needed but it can still look stock when you are done, just stretched a little. __________________ miSSed opportunity - ground up creation of an AWD 1994 454 SS that never was http://67-72chevytrucks.com/vboard/s...d.php?t=795577 69 C10 shortbed stepside 400 small block - built like what a super sport truck could have been 69 K20 lwb TBI 350 4L60E NP208 14-bolt Dana-44 w/disc 68 Camaro SS / RS 500hp 439 inch roller cam big block 4L80E 79 Malibu TPI 350 4L60 w/ Z28 steering & sway bars

03-04-2011, 05:54 PM	#743
propanemudtruck Local Redneck Authority Join Date: Mar 2009 Location: Grand Rapids, MI Posts: 584	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. As long as the dash isn't in the middle of the doorway.... Much talent in this build, thank you again for sharing! __________________ -Kevin four on the floor feel the beat in your soul movin to the rhythym pumpin til ya cant take no more dance if you want to do what you came to you cant ignore the feeling of that four on the floor

03-04-2011, 06:28 PM	#744
JasonBird '67 C-10 LWB Driver Join Date: Dec 2010 Location: Andover, Kansas Posts: 380	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. lol, i think the back seats just got smaller!! JK ;-) __________________ '67 C-10 LWB - My Build Thread '67 C-20 LWB - My Donor/ Parts truck - SOLD! '92 GMC SAFARI VAN - My Parts Go Getter '06 KIA SPORTAGE EX - My Commuter "All of this crap better make a truck!" - my wife Sue. Proud U.S.M.C. Dad!

03-04-2011, 07:50 PM	#745
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Abracadabra POOF Attached Images __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife! Last edited by drewskiren; 03-04-2011 at 07:52 PM.

03-04-2011, 07:56 PM	#746
67chevy1series Registered User Join Date: Mar 2010 Location: a t w a t e r cali 95301 Posts: 10,713	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. wow that is awsome yes gru did have the tool you needed well i hope it works better than it looks.....that looks kinda ugly... but its ugly because it was kept inside anewer dash.....anyways drew great progress

03-04-2011, 08:01 PM	#747
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Nice job shoehorning that in It doesn't stick down that much lower than a stock A/C box actually...probably 3-4" or so more.... ...are you going to be able to integrate the controls somehow? __________________ Looking for a 67-72 swb or blazer project in or around VA.



Register or Log In To remove these advertisements.

03-04-2011, 08:17 PM	#748
Pop's C-10 Registered User Join Date: Jul 2010 Location: memphis Posts: 2,537	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Nice...who needs a glove box anyway....lol You running beanch or buckets...

03-04-2011, 08:23 PM	#749
JasonBird '67 C-10 LWB Driver Join Date: Dec 2010 Location: Andover, Kansas Posts: 380	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. that is some nice photoshoppin'!! __________________ '67 C-10 LWB - My Build Thread '67 C-20 LWB - My Donor/ Parts truck - SOLD! '92 GMC SAFARI VAN - My Parts Go Getter '06 KIA SPORTAGE EX - My Commuter "All of this crap better make a truck!" - my wife Sue. Proud U.S.M.C. Dad!

Register or Log In To remove these advertisements.