** YOUNG FRANKENSTEIN ** The truck Chevrolet should have built. - Page 5 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Dieselwrencher** · 11-02-2010, 02:59 PM

I've actually thought about doing a steel inner if I did this project. I wonder if you could take another roof skin from another burb, or the left over from the rear of the cut off area that is not used at all, trim it down and use it? Maybe put some bows in there first, tack them to the outer skin and the inner top of the burb roof to cab framing. Then place the trimmed burb roof skin in and pre drill some holes to be able to spot weld to the bows. This would be real easy to do if you have a way to stand the cab up on its back or flip it on its side I think. IDK, just some ideas I have been tossing around.

ksbrktracer · 11-02-2010, 03:07 PM

Just a thought ..... How about the inner skin out of a newer crew cab ???

68 TT · 11-02-2010, 03:07 PM

Quote:

Originally Posted by Dieselwrencher

I've actually thought about doing a steel inner if I did this project. I wonder if you could take another roof skin from another burb, or the left over from the rear of the cut off area that is not used at all, trim it down and use it? Maybe put some bows in there first, tack them to the outer skin and the inner top of the burb roof to cab framing. Then place the trimmed burb roof skin in and pre drill some holes to be able to spot weld to the bows. This would be real easy to do if you have a way to stand the cab up on its back or flip it on its side I think. IDK, just some ideas I have been tossing around.

It will be a ton of work either way to get a smooth headliner.

A traditional vinyl one with bows like a 60's car used would be easiest. Just bend up some 1/4" rod to the contour you want and mount them with clips in the center and receiver pockets on the edges to hold them in place. Hand it off to an upholstery shop and let them have at it. The edge trim may take a little work but nowhere near what the smooth headliners would take. The upholstery shop could probably take care of the edge trim too.

68 TT · 11-02-2010, 03:14 PM

Quote:

Originally Posted by ksbrktracer

Just a thought ..... How about the inner skin out of a newer crew cab ???

Cut that out. It would be too easy.

Maybe.

I think the newer cab is a bit wider at the top but it would be a good place to start. A little sectioning and welding and it could work out pretty well with a whole lot less work than fabricating one from scratch.

**Dieselwrencher** · 11-02-2010, 03:15 PM

Personally, I'd either want a steel inner of go the fiberglass route. My friend had a 48 Chevy the size of a crew cab but only a 2 door. He had an old style cloth and bow headliner in it once. It just looked out of place so he built a fiberglass one. That was the ticket! 5 years later he built another one and this time he did steel. That was even better IMO.

**67cheby** · 11-02-2010, 03:18 PM

why not just weld a couple of reg cab inner roof panels together and make it look like it was made that way ??

ksbrktracer · 11-02-2010, 03:25 PM

Quote:

Originally Posted by 67cheby

why not just weld a couple of reg cab inner roof panels together and make it look like it was made that way ??

That was my first thought , probably need 3-4 of them to get enough metal I'm guessing

**Dieselwrencher** · 11-02-2010, 03:29 PM

That is a good idea too. It would be a lot of cutting and welding, but I guess that is the whole project.

**67cheby** · 11-02-2010, 03:31 PM

i think it would be a lot more "impressive" and look like it is done right !! i saw an extended cab 68 done like this prob 15 years ago , and i still remember that trucks headliner today !!

68 TT · 11-02-2010, 03:34 PM

Quote:

Originally Posted by 67cheby

i think it would be a lot more "impressive" and look like it is done right !! i saw an extended cab 68 done like this prob 15 years ago , and i still remember that trucks headliner today !!

It would be a whole lot easier to find a few regular cab roof sections than it would to snag one crew cab roof too.

scooterskoolkustoms · 11-02-2010, 03:37 PM

WOW you have some balls,the truck was nice to start with and you are doing a great job.not just anybody can cut up a truck,keep up the good,no I mean great job.

JRBECK64 · 11-03-2010, 09:32 PM

I am completely blown out of my socks by this build. My hats off to you and I dont take my hat off for anyone. Its refreshing to see new ideas coming to fruition. GREAT JOB.

JRBECK64

drewskiren · 11-03-2010, 11:51 PM

Quote:

Originally Posted by scooterskoolkustoms

WOW you have some balls,the truck was nice to start with and you are doing a great job.not just anybody can cut up a truck,keep up the good,no I mean great job.

Quote:

Originally Posted by JRBECK64

I am completely blown out of my socks by this build. My hats off to you and I dont take my hat off for anyone. Its refreshing to see new ideas coming to fruition. GREAT JOB.

JRBECK64

Thanks so much for the props!

Strut · 11-04-2010, 07:46 AM

What do you think about getting a Headliner out of a new model Tahoe or Suburban? I dont know what the size of your roof is, but if the headliner was to big it would be easy to cut and glue back together.... Then you have a foundation for you fiberglass work.... Should be able to soak the headliner with resin and harden it. You might still want to use some fiberglass mat to reinforce it some.

Just an idea...

drewskiren · 11-05-2010, 10:50 PM

Quote:

Originally Posted by Strut

What do you think about getting a Headliner out of a new model Tahoe or Suburban? I dont know what the size of your roof is, but if the headliner was to big it would be easy to cut and glue back together.... Then you have a foundation for you fiberglass work.... Should be able to soak the headliner with resin and harden it. You might still want to use some fiberglass mat to reinforce it some.

Just an idea...

Just the kind of idea I am looking for!!! Might work.

jbclassix · 11-06-2010, 07:01 AM

my suggestion is a 1992-2000 chevy crew cab headliner if you are going to put in a headliner. it has a low roofline and simple curves. otherwise, what about using several inner roof pieces from a truck and then covering them with material? It wouldnt be removeable though.

**Hart_Rod** · 11-06-2010, 08:53 AM

Quote:

Originally Posted by 67cheby

why not just weld a couple of reg cab inner roof panels together and make it look like it was made that way ??

That's how mine was done. here's a couple of pictures:

ksbrktracer · 11-06-2010, 10:48 AM

We have a winner ... That's the way I would do mine. Then maybe add a super headliner ....!!

**67cheby** · 11-06-2010, 10:53 AM

That looks killer, imho that is the only thing that looks right !! Nice job by the way

**Hart_Rod** · 11-06-2010, 11:35 AM

Thanks. Drew, have you started on your chassis yet? If you have questions, give me a call.

R/

FRENCHBLUE72 · 11-06-2010, 01:10 PM

I like the steel headliner idea looks factory..

drewskiren · 11-06-2010, 01:47 PM

Quote:

Originally Posted by Hart_Rod

That's how mine was done. here's a couple of pictures:

Quote:

Originally Posted by ksbrktracer

We have a winner ... That's the way I would do mine. Then maybe add a super headliner ....!!

Quote:

Originally Posted by 67cheby

That looks killer, imho that is the only thing that looks right !! Nice job by the way

Quote:

Originally Posted by FRENCHBLUE72

I like the steel headliner idea looks factory..

My reinforcing rib hangs down in the way. Can't do it that way/ worried if I take out the rib it is too flexy. I really want a cloth headliner on a cardboard/fiberglass insert. Now I am thinking about how to make that and finish the edges.

**67cheby** · 11-06-2010, 02:23 PM

the headliner would be the support you need that would take the place of the bow your talking about

**Palf70Step** · 11-06-2010, 05:16 PM

Beautiful work so far. I am really enjoying your build.

drewskiren · 11-07-2010, 07:36 PM

Remember the 100 dollar cabs I got? Well they came with doors too which I need to steal something off of. Measured 3 or 4 times on the drivers side only to cut it an eighth inch too short. DOH!!! Some surgeon I am. Passenger side I drilled out the spot welds and removed a good bit into the door. I'll just plug weld the holes at the bottom and butt weld at the top frame.

11-02-2010, 02:59 PM	#101
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,139	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I've actually thought about doing a steel inner if I did this project. I wonder if you could take another roof skin from another burb, or the left over from the rear of the cut off area that is not used at all, trim it down and use it? Maybe put some bows in there first, tack them to the outer skin and the inner top of the burb roof to cab framing. Then place the trimmed burb roof skin in and pre drill some holes to be able to spot weld to the bows. This would be real easy to do if you have a way to stand the cab up on its back or flip it on its side I think. IDK, just some ideas I have been tossing around. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

11-02-2010, 03:07 PM	#102
ksbrktracer TNT-MOTORSPORTS Join Date: Mar 2008 Location: TULSA OKLAHOMA Posts: 2,692	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Just a thought ..... How about the inner skin out of a newer crew cab ???

11-02-2010, 03:15 PM	#105
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,139	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Personally, I'd either want a steel inner of go the fiberglass route. My friend had a 48 Chevy the size of a crew cab but only a 2 door. He had an old style cloth and bow headliner in it once. It just looked out of place so he built a fiberglass one. That was the ticket! 5 years later he built another one and this time he did steel. That was even better IMO. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

11-02-2010, 03:18 PM	#106
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. why not just weld a couple of reg cab inner roof panels together and make it look like it was made that way ?? __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

11-02-2010, 03:29 PM	#108
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,139	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. That is a good idea too. It would be a lot of cutting and welding, but I guess that is the whole project. __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

11-02-2010, 03:31 PM	#109
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. i think it would be a lot more "impressive" and look like it is done right !! i saw an extended cab 68 done like this prob 15 years ago , and i still remember that trucks headliner today !! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

11-02-2010, 03:37 PM	#111
scooterskoolkustoms Registered User Join Date: Feb 2010 Location: so cal Posts: 436	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. WOW you have some balls,the truck was nice to start with and you are doing a great job.not just anybody can cut up a truck,keep up the good,no I mean great job. __________________ big old burb in primer.lot of work to do.

11-03-2010, 09:32 PM	#112
JRBECK64 Registered User Join Date: Sep 2008 Location: Cornelius Oregon Posts: 1,073	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I am completely blown out of my socks by this build. My hats off to you and I dont take my hat off for anyone. Its refreshing to see new ideas coming to fruition. GREAT JOB. JRBECK64

11-04-2010, 07:46 AM	#114
Strut Registered User Join Date: Oct 2009 Location: Corbin Ky Posts: 247	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. What do you think about getting a Headliner out of a new model Tahoe or Suburban? I dont know what the size of your roof is, but if the headliner was to big it would be easy to cut and glue back together.... Then you have a foundation for you fiberglass work.... Should be able to soak the headliner with resin and harden it. You might still want to use some fiberglass mat to reinforce it some. Just an idea... __________________ 1972 Chevy C10 SWB 1999 GMC Sonoma Mini 2008 Yamaha R1 2007 Harley Nightster

11-06-2010, 07:01 AM	#116
jbclassix Junk Yartist Join Date: Jul 2009 Location: Greeley, CO Posts: 2,203	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. my suggestion is a 1992-2000 chevy crew cab headliner if you are going to put in a headliner. it has a low roofline and simple curves. otherwise, what about using several inner roof pieces from a truck and then covering them with material? It wouldnt be removeable though. __________________ -Jeremy YOU ONLY FAIL IF YOU STOP TRYING 70 Crew Cab Build Link 70 GMC Suburban 4X4 build thread 95 Yukon Daily Driver Rebuilding an NP205

11-06-2010, 10:48 AM	#118
ksbrktracer TNT-MOTORSPORTS Join Date: Mar 2008 Location: TULSA OKLAHOMA Posts: 2,692	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. We have a winner ... That's the way I would do mine. Then maybe add a super headliner ....!!

11-06-2010, 10:53 AM	#119
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. That looks killer, imho that is the only thing that looks right !! Nice job by the way __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

11-06-2010, 11:35 AM	#120
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,856	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Thanks. Drew, have you started on your chassis yet? If you have questions, give me a call. R/ __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

11-06-2010, 01:10 PM	#121
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,608	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. I like the steel headliner idea looks factory.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-06-2010, 02:23 PM	#123
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. the headliner would be the support you need that would take the place of the bow your talking about __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172



Register or Log In To remove these advertisements.

11-06-2010, 05:16 PM	#124
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,083	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Beautiful work so far. I am really enjoying your build. __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

11-07-2010, 07:36 PM	#125
drewskiren Lucky Teter at the wheel Join Date: Aug 2009 Location: Memphis, TN Posts: 1,896	Re: YOUNG FRANKENSTEIN The truck Chevrolet should have built. Remember the 100 dollar cabs I got? Well they came with doors too which I need to steal something off of. Measured 3 or 4 times on the drivers side only to cut it an eighth inch too short. DOH!!! Some surgeon I am. Passenger side I drilled out the spot welds and removed a good bit into the door. I'll just plug weld the holes at the bottom and butt weld at the top frame. Attached Images __________________ Drew YOUNG FRANKENSTEIN (Finished with MAJOR Surgery - IT'S ALIVE!!!) The Bride is currently under the knife!

Register or Log In To remove these advertisements.