Frame mount hitch - The 1947 - Present Chevrolet & GMC Truck Message Board Network

tdangle · 02-03-2020, 11:44 PM

I purchased a Drawtite hitch 41504, a class 3 hitch with max rating of 1000 lb / 10,000 lb gross weight. Bought at Amazon for $120.

Happy to report install was easy and I was able to keep the spare tire.

I bolted the side pieces to the cross piece of the hitch and then raised it into place after dropping the spare tire. I used C clamps to hold in place while I marked the holes. Drilled 6 1/2" holes stepping up from 1/8" to 1/4" then 1/2". (Hint: Use new or sharpened drill bits)

Bolted into place and raised tire into place. I was not able to secure the tire with the cross piece as the bar was hitting the side plate of the hitch on the passenger side. I placed 2 short pieces of 2x6 on top of the tire to take up the gap between the top of the tire and the 2 bars the top of the tire pushes against and was able to secure the tire.

Redneck Rydes · 02-04-2020, 12:43 AM

Looks good!

SWEET7T · 02-04-2020, 09:40 AM

Glad to see that it fits with the step bumper. How far back does the receiver tube stick out, any, a lot?
Too bad it doesn't tuck up closer though. For $120, I could live with it (or modify).

Thank you for the info!

tdangle · 02-04-2020, 11:13 AM

Quote:

Originally Posted by SWEET7T

Glad to see that it fits with the step bumper. How far back does the receiver tube stick out, any, a lot?
Too bad it doesn't tuck up closer though. For $120, I could live with it (or modify).

Thank you for the info!

It is about 3 inches back under my bumper

cornerstone · 02-04-2020, 03:08 PM

Looks great Terry. Would you mind posting a picture from the lower side view so I can see where the end of the hitch resides?

tdangle · 02-04-2020, 04:02 PM

Here you go. As you can see from the underside of the bumper, the drop hitch was welded well. It took a cutting torch and bit of work to remove it. I haven't bothered to clean it up. Let me know if this is what you need.

Astro-Balls · 02-04-2020, 06:19 PM

Nice, Would that work the same for a '68 LB C20?

tdangle · 02-04-2020, 08:53 PM

Quote:

Originally Posted by Astro-Balls

Nice, Would that work the same for a '68 LB C20?

I would think so. Can't image they changed the frame much if at all.

**Ol Blue K20** · 02-04-2020, 10:01 PM

Thanks for the info. My "Buddy" was going to charge $300.00 for the same part #. I ordered it through Amazon.

**davischevy** · 02-05-2020, 01:00 AM

Good info.

cornerstone · 02-05-2020, 02:57 PM

Quote:

Originally Posted by tdangle

Here you go. As you can see from the underside of the bumper, the drop hitch was welded well. It took a cutting torch and bit of work to remove it. I haven't bothered to clean it up. Let me know if this is what you need.

It's the perfect shot! I appreciate you taking the time to do that for me.

Brian

**Ol Blue K20** · 02-13-2020, 10:46 AM

I installed mine yesterday. Fairly straight forward installation and fits nice.

02-03-2020, 11:44 PM	#1
tdangle Registered User Join Date: Mar 2005 Location: Jurupa Valley, Ca Posts: 1,210	Frame mount hitch I purchased a Drawtite hitch 41504, a class 3 hitch with max rating of 1000 lb / 10,000 lb gross weight. Bought at Amazon for $120. Happy to report install was easy and I was able to keep the spare tire. I bolted the side pieces to the cross piece of the hitch and then raised it into place after dropping the spare tire. I used C clamps to hold in place while I marked the holes. Drilled 6 1/2" holes stepping up from 1/8" to 1/4" then 1/2". (Hint: Use new or sharpened drill bits) Bolted into place and raised tire into place. I was not able to secure the tire with the cross piece as the bar was hitting the side plate of the hitch on the passenger side. I placed 2 short pieces of 2x6 on top of the tire to take up the gap between the top of the tire and the 2 bars the top of the tire pushes against and was able to secure the tire. Attached Images __________________ Terry 1970 Custom Camper/C20 , GM Crate 350/7004R, Dana 60, factory AC

02-04-2020, 12:43 AM	#2
Redneck Rydes Registered User Join Date: Feb 2016 Location: Trenton,Ontario & South Carolina Posts: 755	Re: Frame mount hitch Looks good!

02-04-2020, 09:40 AM	#3
SWEET7T Try spinnin 4 rear tars Join Date: Sep 2003 Location: Salt Lake City, Utah Posts: 757	Re: Frame mount hitch Glad to see that it fits with the step bumper. How far back does the receiver tube stick out, any, a lot? Too bad it doesn't tuck up closer though. For $120, I could live with it (or modify). Thank you for the info! __________________ SWEET7T 1970 C10, 2wd, LB, 307/TH350/3.08. PS, PB

02-04-2020, 03:08 PM	#5
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: Frame mount hitch Looks great Terry. Would you mind posting a picture from the lower side view so I can see where the end of the hitch resides? __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

02-04-2020, 04:02 PM	#6
tdangle Registered User Join Date: Mar 2005 Location: Jurupa Valley, Ca Posts: 1,210	Re: Frame mount hitch Here you go. As you can see from the underside of the bumper, the drop hitch was welded well. It took a cutting torch and bit of work to remove it. I haven't bothered to clean it up. Let me know if this is what you need. Attached Images __________________ Terry 1970 Custom Camper/C20 , GM Crate 350/7004R, Dana 60, factory AC

02-04-2020, 06:19 PM	#7
Astro-Balls Registered User Join Date: Feb 2019 Location: Nor Cal Posts: 822	Re: Frame mount hitch Nice, Would that work the same for a '68 LB C20? __________________ 1968 C20 Fleetside 396 4sp PS PB AC CST . https://www.youtube.com/watch?v=RWK8GgWD4uA

02-04-2020, 10:01 PM	#9
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 16,242	Re: Frame mount hitch Thanks for the info. My "Buddy" was going to charge $300.00 for the same part #. I ordered it through Amazon. __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul

02-05-2020, 01:00 AM	#10
davischevy Senior Member Join Date: Sep 2008 Location: Harrison, Arkansas Posts: 9,834	Re: Frame mount hitch Good info. __________________ other Larry Build thread, Arkansas K10 https://67-72chevytrucks.com/vboard/...=755797&page=5 The ability to speak several languages is an asset, but the ability to keep your mouth shut in any language is priceless.

02-13-2020, 10:46 AM	#12
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 16,242	Re: Frame mount hitch I installed mine yesterday. Fairly straight forward installation and fits nice. __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man R.I.P. FleetsidePaul



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.