Inline 6 manifold/carb warmers? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

63whoopie · 10-27-2009, 06:15 PM

Ok, so I am planning on adding some sort of aftermarket intake to my I6 250 in my 1963 C10. I've bid on a few 2x2 intakes, and, most recently, a single 4-bbl intake in Ebay. My question is:
I keep reading that you need to heat the fuel mixture for regular driving my tapping a hole in the manifold, etc. I heard someone in my hometown recently say that you could just use a heated spacer (?) so as not to have to tap the manifold, and add the space of a carb spacer for the fuel density. Does anyone do this, recommended for or against, or have an opinion on whether to tap the manifold or look for a spacer than is set up to be heated? Clifford apparently might have made a heated spacer, but doesn't anymore, I checked.

Thanks in advance.

**slepysal** · 10-27-2009, 06:48 PM

My 60 it has an old Clifford, with no heat provision, but hear in San Jose it isnt that big of a problem.
Clifford now makes there manifold with the provision to use water to heat the intake, Offy's are made to "bolt" to your stock exhuast or to use an an addapter available thru Tom Langdon I m sure some one will post the website , if not Ill find it for you
Good luck and post some pics
Hey Chief I got the Offy for you.

ol Curt · 10-27-2009, 08:42 PM

www.stoveboltengineco.com/

**ChiefRocka** · 10-27-2009, 08:51 PM

Quote:

Originally Posted by slepysal

My 60 it has an old Clifford, with no heat provision, but hear in San Jose it isnt that big of a problem.
Clifford now makes there manifold with the provision to use water to heat the intake, Offy's are made to "bolt" to your stock exhuast or to use an an addapter available thru Tom Langdon I m sure some one will post the website , if not Ill find it for you
Good luck and post some pics
Hey Chief I got the Offy for you.

How'd you know I'd be reading this !!

Got a pic ?? PM me man !!!

63whoopie · 10-27-2009, 10:28 PM

ok, found one of the carb spacer/ heater plates i had heard of. Apparently, they're out of production, and have been for some time. I am going to guess that this will be just as good as tapping the manifold itself?

**slepysal** · 10-27-2009, 11:53 PM

Quote:

Originally Posted by ChiefRocka

How'd you know I'd be reading this !!

Got a pic ?? PM me man !!!

Will take some tomorow

what type of manifold do you have ?
try this as olcurt sugested
http://www.stoveboltengineco.com/aca...?productid=144

ol Curt · 10-28-2009, 07:53 AM

I used an Offenhauser intake on with dual Rochester carbs and the heater plate from Langdon. It worked fine on mine.

10-27-2009, 06:15 PM	#1
63whoopie Registered User Join Date: Oct 2009 Location: Tuscaloosa, Alabama Posts: 37	Inline 6 manifold/carb warmers? Ok, so I am planning on adding some sort of aftermarket intake to my I6 250 in my 1963 C10. I've bid on a few 2x2 intakes, and, most recently, a single 4-bbl intake in Ebay. My question is: I keep reading that you need to heat the fuel mixture for regular driving my tapping a hole in the manifold, etc. I heard someone in my hometown recently say that you could just use a heated spacer (?) so as not to have to tap the manifold, and add the space of a carb spacer for the fuel density. Does anyone do this, recommended for or against, or have an opinion on whether to tap the manifold or look for a spacer than is set up to be heated? Clifford apparently might have made a heated spacer, but doesn't anymore, I checked. Thanks in advance.

10-27-2009, 06:48 PM	#2
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,080	Re: Inline 6 manifold/carb warmers? My 60 it has an old Clifford, with no heat provision, but hear in San Jose it isnt that big of a problem. Clifford now makes there manifold with the provision to use water to heat the intake, Offy's are made to "bolt" to your stock exhuast or to use an an addapter available thru Tom Langdon I m sure some one will post the website , if not Ill find it for you Good luck and post some pics Hey Chief I got the Offy for you. __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

10-27-2009, 08:42 PM	#3
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: Inline 6 manifold/carb warmers? www.stoveboltengineco.com/ __________________ 1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down!

10-27-2009, 10:28 PM	#5
63whoopie Registered User Join Date: Oct 2009 Location: Tuscaloosa, Alabama Posts: 37	Re: Inline 6 manifold/carb warmers? ok, found one of the carb spacer/ heater plates i had heard of. Apparently, they're out of production, and have been for some time. I am going to guess that this will be just as good as tapping the manifold itself?

10-28-2009, 07:53 AM	#7
ol Curt Junior Member Join Date: Dec 2006 Location: Newburgh, IN Posts: 1,247	Re: Inline 6 manifold/carb warmers? I used an Offenhauser intake on with dual Rochester carbs and the heater plate from Langdon. It worked fine on mine. __________________ 1966 Chevy C10 Longbed I'm Bob....ol Curt was my Grandpa The truck was his and he sure as heck wouldn't understand why I took a perfectly good truck and tore it down!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.