factory rear sway bars!!!!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Longhorn Man · 05-23-2004, 12:01 AM

I have not looked this up in any books yet, but I think I found a factory rear sway bar on a 68 P-30.
Some of you may remember this truck from a thread ( http://64.246.42.114/vboard/showthread.php3?t=91930 ) when I mentioned I had to install a 350 in it verses the original 307.
Any ways, i was under it today fixing the dead fuel guage (shorted wire) and I noticed it has a rear sway bar. (!!!!)
The links where it goes to the frame were rusted out, and I called the head guy at there wearhouse...I left a message asking to pull off the inoperable sway bar in the rear. He follows the train of thought that if it is doing fine without it...don't add it (Or repair it) With anyluck, I'll be able to take it off and mount it onto the Longhorn. (same chassis pretty much)
Pretty sweet huh?

**Canadian694x4** · 05-23-2004, 01:19 AM

Sweeeet Score Dude!

69 Short Fleet · 05-23-2004, 03:11 AM

Ever Neat, how big in dia. is the bar Andy? Any pics? Regards Doug

Longhorn Man · 05-23-2004, 12:21 PM

No pics yet...I didn't measure the bar, but it was huge.
I am thinking well over 15/16 inch

05-23-2004, 12:01 AM	#1
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	factory rear sway bars!!!!! I have not looked this up in any books yet, but I think I found a factory rear sway bar on a 68 P-30. Some of you may remember this truck from a thread ( http://64.246.42.114/vboard/showthread.php3?t=91930 ) when I mentioned I had to install a 350 in it verses the original 307. Any ways, i was under it today fixing the dead fuel guage (shorted wire) and I noticed it has a rear sway bar. (!!!!) The links where it goes to the frame were rusted out, and I called the head guy at there wearhouse...I left a message asking to pull off the inoperable sway bar in the rear. He follows the train of thought that if it is doing fine without it...don't add it (Or repair it) With anyluck, I'll be able to take it off and mount it onto the Longhorn. (same chassis pretty much) Pretty sweet huh?

05-23-2004, 01:19 AM	#2
Canadian694x4 Born To Lose Club Join Date: Feb 2003 Location: Calgary, Alberta/Oxenden, Ontario, Great White North Posts: 13,306	Sweeeet Score Dude! __________________ Brian Smith - "Born To Lose" 1969 Chevrolet K10 LWB Fleetside - Proud Owner For 20 Yrs - 1 of 208 Built & Sold In Canada! - 283 V8/350TH/NP208, 2" All Spring Lift, 32" Good Year MT/R's. 1972 GMC K2500 Custom LWB Fleetside - Proud Owner For 2 Yrs - 1 of 571 Built & Sold In Canada! - 350 V8/SM465/NP205, 4” Rough Country Lift, 33” Interco TSL Thornbirds 2007.5 GMC Sierra SLE 2500HD 4x4 - Proud Owner For 15 Yrs - 6.6L V8 Duramax Diesel/Allison 1000, 2" Lift, 33" Mickey Thompson MTZ's. 2008 Yamaha Raptor 700r - Proud Owner For 13 Yrs - ITP Mud Lites. 2015 John Deere 1025R - Proud Owner For 6 Yrs - 24HP Diesel/H120/54D/260B/SB1154.

05-23-2004, 03:11 AM	#3
69 Short Fleet Registered User Join Date: Nov 2002 Location: Kelowna B.C. Canada Posts: 1,086	Ever Neat, how big in dia. is the bar Andy? Any pics? Regards Doug

05-23-2004, 12:21 PM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	No pics yet...I didn't measure the bar, but it was huge. I am thinking well over 15/16 inch



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.