Who has recently installed front engine harness - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**pound41** · 06-05-2004, 05:47 PM

Some guys over on the blazer board were talking about the installation of the painless front engine harness. Since a few are getting ready to do it. I remember a post a month or so back about that harness and its install. Someone was talking about one of the front lights being incorrect and what adjustments had to be made. thanks for the help

**JIMs70GMC** · 06-05-2004, 09:31 PM

Randy70c-10 did, not to long ago.

*Randy70C-10* · 06-05-2004, 09:35 PM

Yeah, I did one. I tried to find the post but didn't have much luck. There was something with the lights that I can't remember but it was easy to figure out (and I'm color blind)

*Randy70C-10* · 06-05-2004, 09:49 PM

I just found the post. Bummer, the pics aren't there anymore, but I read the post and all the wires match right up. From what I remember, the one of the sidemarkers didn't match but the wire is labeled anyhow so you can't mess it up.

06-05-2004, 05:47 PM	#1
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,269	Who has recently installed front engine harness Some guys over on the blazer board were talking about the installation of the painless front engine harness. Since a few are getting ready to do it. I remember a post a month or so back about that harness and its install. Someone was talking about one of the front lights being incorrect and what adjustments had to be made. thanks for the help

06-05-2004, 09:31 PM	#2
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Randy70c-10 did, not to long ago. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

06-05-2004, 09:35 PM	#3
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	Yeah, I did one. I tried to find the post but didn't have much luck. There was something with the lights that I can't remember but it was easy to figure out (and I'm color blind)

06-05-2004, 09:49 PM	#4
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	I just found the post. Bummer, the pics aren't there anymore, but I read the post and all the wires match right up. From what I remember, the one of the sidemarkers didn't match but the wire is labeled anyhow so you can't mess it up.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.