|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-16-2004, 10:09 AM
|
#1 |
|
70' blazer
Join Date: Apr 2004
Location: Durham, NC
Posts: 71
|
WTB: High Hump Transmission Cover
I would like to buy a high hump tranny cover that bolts down on the inside of the cab floor. If you have a extra one that you want to get rid of, you can reply here or email brattonbe@aro.army.mil
 Oops goes in a 70' Blazer/3-speed in floor.
|
|
|
|
06-16-2004, 10:27 AM
|
#2 |
|
Post Whore
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
06-16-2004, 12:29 PM
|
#3 |
|
Just like to part out trucks!!
Join Date: Nov 2001
Location: Meriden, Ks-North of Topeka 10 miles
Posts: 27,396
|
I got about 10 of them probably, which one do you need. No holes, 4 speed only, 4 speed with 4x4. $25 plus shipping. Thanks Randy
__________________
67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure" |
|
|
|
|
06-16-2004, 12:50 PM
|
#4 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Make sure you get one with the transfer case hole on the correct side. 71-72 right, 70 left not sure about the rockwell transfer case ones.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
06-16-2004, 01:22 PM
|
#5 |
|
70' blazer
Join Date: Apr 2004
Location: Durham, NC
Posts: 71
|
yahoo
Teeitup, I'm sending you a pm.
|
|
|
|
|
06-17-2004, 11:10 PM
|
#6 |
|
Just like to part out trucks!!
Join Date: Nov 2001
Location: Meriden, Ks-North of Topeka 10 miles
Posts: 27,396
|
Here are some of them I have
__________________
67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure" |
|
|
|
|
06-18-2004, 07:23 AM
|
#7 |
|
70' blazer
Join Date: Apr 2004
Location: Durham, NC
Posts: 71
|
I'll take one
I sent you another pm,
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
