'99 Tahoe Keyless remote programing - The 1947 - Present Chevrolet & GMC Truck Message Board Network

87 STEPPER · 06-22-2004, 11:05 PM

Any one know or have the procedure for doing this i just won a spare remote on ebay but need to reprogram it for my truck.

Tnkx.

Old Dave · 06-23-2004, 08:47 AM

I found this on another site:http://www.automotiveforums.com/vbul...d.php?t=162483

99-2door · 06-23-2004, 01:26 PM

From that post, this is the procedure you need.

Originally posted in another thread by "GMMERLIN" instructions on programming a 99 suburban-----
When reprogramming the remote control door lock reciever, All transmitters must be programmed at this time in order for the transmitters to operate the vehicle. Transmitters not programed at this time will not work and the procedure will have to be redone with all the transmitters.

Ground pin 4 to pin 8 of the data link connector (DLC). The receiver will respond by locking and unlocking the doors, and activating the liftgate window release (if equipped) within 2 seconds.
Press and hold the LOCK and UNLOCK buttons simultaneously on the first transmitter to be programmed until the locks cycle (approximately 10 seconds).
Repeat step 2 for up to four total transmitters to be programmed (if available). The receiver will respond by locking and unlocking the doors and activating the liftgate window release (if equipped) within 2 seconds.
Remove the ground applied to the DLC.
Lock and unlock the doors in order to verify the transmitter operation.
Activate the rear window release in order to verify the transmitter operation.

Old Dave · 06-23-2004, 02:22 PM

Thanks 99 2-door...not too good on cutting & pasting yet. Hope this works for him.

87 STEPPER · 06-23-2004, 07:19 PM

Hey thanks alot guys i'll giver a try when i receive the new remote.

87 STEPPER · 06-29-2004, 06:21 PM

Well today i tried that procedure out and it worked perfectly now i have a good spare.

Thanks Old Dave and 99-2door.

06-22-2004, 11:05 PM	#1
87 STEPPER STILL PLAYS WITH TRUX Join Date: Nov 2002 Location: Melbourne, Fla. Posts: 2,764	'99 Tahoe Keyless remote programing Any one know or have the procedure for doing this i just won a spare remote on ebay but need to reprogram it for my truck. Tnkx. __________________ ~~Bruce~~ MY 87 STEPPER MY 99 2D/WD TAHOE

06-23-2004, 08:47 AM	#2
Old Dave Is a bullfrog waterproof? Join Date: Nov 2000 Location: OLATHE, KANSAS Posts: 1,130	I found this on another site:http://www.automotiveforums.com/vbul...d.php?t=162483 __________________ "It is better to remain silent and be thought a fool, than to open one's mouth and remove all doubt." Ben Franklin __________________ 1970 Chevy shortbed 2002 Harley Custom Chopper (Long sucker) 1998 K2500 5.7L 5-speed Longbed 1st two are My son's toys...they just live in my garage! 1997 GMC K1500 Suburban 1993 S-10 Blazer 4D (youngest son's daily driver) 2000 Dodge Ram 4WD Ext. Cab (5.9L) Wife is a late year 1951

06-23-2004, 01:26 PM	#3
99-2door Registered User Join Date: Oct 2003 Location: Broken Bow, OK Posts: 1,385	From that post, this is the procedure you need. Originally posted in another thread by "GMMERLIN" instructions on programming a 99 suburban----- When reprogramming the remote control door lock reciever, All transmitters must be programmed at this time in order for the transmitters to operate the vehicle. Transmitters not programed at this time will not work and the procedure will have to be redone with all the transmitters. Ground pin 4 to pin 8 of the data link connector (DLC). The receiver will respond by locking and unlocking the doors, and activating the liftgate window release (if equipped) within 2 seconds. Press and hold the LOCK and UNLOCK buttons simultaneously on the first transmitter to be programmed until the locks cycle (approximately 10 seconds). Repeat step 2 for up to four total transmitters to be programmed (if available). The receiver will respond by locking and unlocking the doors and activating the liftgate window release (if equipped) within 2 seconds. Remove the ground applied to the DLC. Lock and unlock the doors in order to verify the transmitter operation. Activate the rear window release in order to verify the transmitter operation. __________________ 95 K3500 SRW 5.7L Vortec 4L80e 4.10 G80 2001 GMC C3 6.0 AWD, Volant, 3/5 drop TBSS intake, HP tuners, pullies, 05 efans, 05 front brakes, etc. 2003 Tahoe Z71 Silverado front clip

06-23-2004, 02:22 PM	#4
Old Dave Is a bullfrog waterproof? Join Date: Nov 2000 Location: OLATHE, KANSAS Posts: 1,130	Thanks 99 2-door...not too good on cutting & pasting yet. Hope this works for him. __________________ "It is better to remain silent and be thought a fool, than to open one's mouth and remove all doubt." Ben Franklin __________________ 1970 Chevy shortbed 2002 Harley Custom Chopper (Long sucker) 1998 K2500 5.7L 5-speed Longbed 1st two are My son's toys...they just live in my garage! 1997 GMC K1500 Suburban 1993 S-10 Blazer 4D (youngest son's daily driver) 2000 Dodge Ram 4WD Ext. Cab (5.9L) Wife is a late year 1951

06-23-2004, 07:19 PM	#5
87 STEPPER STILL PLAYS WITH TRUX Join Date: Nov 2002 Location: Melbourne, Fla. Posts: 2,764	Hey thanks alot guys i'll giver a try when i receive the new remote. __________________ ~~Bruce~~ MY 87 STEPPER MY 99 2D/WD TAHOE

06-29-2004, 06:21 PM	#6
87 STEPPER STILL PLAYS WITH TRUX Join Date: Nov 2002 Location: Melbourne, Fla. Posts: 2,764	Well today i tried that procedure out and it worked perfectly now i have a good spare. Thanks Old Dave and 99-2door. __________________ ~~Bruce~~ MY 87 STEPPER MY 99 2D/WD TAHOE



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.