3 trucks for sale

[spencra]

I am putting only these trucks up for sale. I am keeping the third. Sadly I do not have any spare time to work on them right now. I would rather sell them than let them sit there until I graduate (Dec 2005). I will try to describe them briefly as best as I can. If you want to know any specifics just let me know and I will answer as best as I can.

1967 C-10: Stepside with 465 tranny (out of truck), no motor. I scrapped the bed because it required way too much work and I also sold the bench seat as I started parting it out. Front clip is in decent shape with good front fenders, rad support needs replacing as well as passenger inner fender. Good rolling chassis with 6 lug mags The cab needs some work but it's not that bad I have some extra parts to go with it.
$300


1979 Cheyenne Pickup: 8ft. bed in good cond. needs very minor work around tirewells and comes with a fiberglass cap. The cab also needs a little attention has mainly some surface rust and needs a little floor work at driver side but I do have a replacement floor pan. Needs new exhaust (dual), tranny has a leak but I am pretty sure that it is a gasket and gas tank has a high leak. Motor is a 350 8 cyl and runs. Headliner and bench seat were redone.
$700 o.b.o. very flexible on this one.

I can e-mail pics if needed

I am also looking for a 48-53 chevy 3100 if anybody is interested in a trade.

Thanks everyone,
Larry.

[Joe67]

PM sent

[biglou55]

Spencra I am coming down to berlin on fri. morn the eighth to put a roof on my bro. & sister inlaws house on ronal drive i will be there until sun. I would love to see your trucks and any extra parts you might have. (like maybe extra stepside fenders He HE ) but i guess it,s not to be. biglou55 Lou Hale

[spencra]

Hey biglou55, If you want I could pm you my address and you could at least do a drive by. Two of the trucks are in the driveway, the stepside is in the garage but I have the link above which will give you an idea of what it looks like. The only difference is that I removed the bed in the picture because it was shot and the bed that I had bought for it is currently sitting on it. The other bed is taking up the other garage bay.
I also took the bench seat out, doors and hood off, and removed the windshied and rear cab window. I could easily pop the stuff back on except for the glass though of course.

[biglou55]

Larry pm me your adress if i get a chance i will have my bro. inlaw swing me by. it,s a shame we couldn,t get to meet. Lou

[spencra]

ttt

[spencra]

ttt, again. I'm just trying to see what kind of interest that I get before I go on my trip.

Thanks everyone,
Larry

[68 chevy truck-TPI]

would you sell the rear fenders off the 67 stepbed?

[spencra]

Sorry 68 chevy truck-TPI, I'd like to get rid of it all together if possible. But if I don't have any luck i'll get back to you on it.

Thanks,
Larry

[67ChevyC10Stepside]

i would be interested in just the bed....

[spencra]

ttt

[botboy]

I wish I could afford to get that '67 C-20 wrecker to minnesota....waaaaaah!!!!

Bump for you anyway....

[GMC71k20]

would you sell the wrecker seperate from the truck?

[Dave Reed]

Still selling stuff?

[spencra]

GMC71k20: I'd like to sell it all together, but anything is possible. I could get back to you later on the wrecker.

discreet007: Yup, still have everything at this point. What are you looking for?

[Dave Reed]

I am looking for a 67'-68' front clip.

[zyggy72]

I'm interested in seeing the 67 wrecker. What kind of body work does it need?

[teeitup]

Dang Larry, if you were closer I'd take both 67's off your hands. Good luck and TTT for you. Randy

[72SUPER4X4]

Larry, please PM me with directions to your place or a phone number that I may reach you at!! I am heading out your way tomorrow and would like to see your two '67 trucks!! I am going to Enfield around 10:00 AM and would like to swing by your place after that.

Thanks, Jeff

[spencra]

discreet007: I'd like to sell them whole at this point but if you are willing to buy a whole truck the wrecker has a nice front clip to it.

zyggy72: it needs cab corners, rockers (which I have), cab mounts, the upper part of the wheel arches on the bed need work and the doors need work (I have two extra doors to go with it, one is in excellent shape the other needs work on the lower part of the door. I do have an inner door skin for that door).

Randy, I wish you lived closer too. I'd like to move these things before the first snowfall but it looks like I might have these things for awhile longer.

Jeff, thanks alot for coming up, it was nice meeting you. Sorry you had to come up this way and leave empty handed. Good luck finding a cab and front clip. I've seen a couple come out of New Jersey and Pennsylvania not too long ago, i'm sure another will pop up again. Good luck again.

Larry.

[Dave Reed]

I am not willing to make that investment right now, but I will let you know if things change.

Thanks, Dave

[tnblazerk5]

can i see a pic or pics of the 67 wrecker ? and does it all work ?

[spencra]

tnblazerk5: The wrecker does work. I had to play with it the first day that I had gotten it. I haven't gotten it running yet though because it needs a starter but the PO said that it was running when he parked it but the starter was bad. I took his word for it but I have not had much time to check it out. I might try to get the starter out within the next couple of weeks before it gets really cold just to try to get it running.

[spencra]

ttt, still got'em

[tnblazerk5]

did ya ever get any pics of the 67wrecker yet ?