FOR SALE/TRADE... 81 K5 4X4 all or Parts, DFW TX - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Staceydude · 11-06-2004, 01:40 PM

Hey All,

I have done some deep thinking and knowing I am going to put a ton of money in whatever project I am building I have decided to get me a 67-72 truck.... So I will be selling my K5 whole or in parts...

Basically it is a roller without tires/wheels

It DOES not have a motor or tranny. However it does have a great NP208 transfer case with TH350 adapter.

The was a smallblock truck.

The body and frame are in great shape...Has alot of newer parts in it.

Newer blower motor

Newer Power steering box

Mile Marker front hubs with good brakes front and rear

Good radiator, front 10 bolt, rear 12 bolt

Good AC condensor

All lights except on front headlight worked great.

Decent top with a few dings and a crack on one of the rails inside the truck could be fixed easily.

Bucket seats and rear seats are there of course but the drivers seat needs recovered

The interior is stripped out, door panels are gone, still have some of the original interior closeout panels for the cab abd rear section

Stripped down tailgate with glass has zero rust

Decent bumpers

Good front fenders etc (front clip has been removed and is in the bed of truck with top on it in my garage)

Hood is also in great shape

In the attached pics you can see the primer along the bottom of the truck, it is virtually rust free, had a set of panels welded in just aft of the rear wheelwell. has a couple of small spots on the floor and bed area. Other than that the truck has been a Texas truck all its life.

Has a good steering collumn with tile and no play whatsoever in the tilt.

Has the original wheel that is near mint.

Does need a windshield it is in but cracked.

Basically I will ad more later as I think about it.

I want to try and sell it all together first so I am only listing a comlete price.. If I part it (which would prolly make me some more money) I will list the indidual parts

As you can see in the pics, this truck is very straight, other than the patched spots, all body panels are original.

I will sell this truck for $300.00

I will take a few payments if someone wishes to give me a deposit and pay it off. couple hundred bucks at a time...

May trade it for some tools... I need a small 110 Welder!!! Hobart handler or Lincoln weldpak etc.

More pics on request.... I lost all my files on the CPU and will have to retake them...

email or PM,

staceybeller@charter.net

Regards,

Stacey

**smokinn** · 11-06-2004, 02:22 PM

man if i had a way of getting it here id give you the 400.00 for it. I could use some of them parts bad.

Jason

Staceydude · 11-06-2004, 09:20 PM

Quote:

Originally Posted by smokinn

man if i had a way of getting it here id give you the 400.00 for it. I could use some of them parts bad.

Jason

Maybe we could work something out gettign it up there somehow.

All PMS retruned as well.

Thanks

Stacey

Staceydude · 11-06-2004, 11:43 PM

Hey all,

I have to go out of town this week to Montreal Canada for work. I will check the post and update it etc. but will not be here to show the truck.

I also have a 73-75 winshield frame for a full convertible conversion I will let go for an extra $70.00 I am listing it seperatly.

Regards,

Stacey

Staceydude · 11-07-2004, 01:45 AM

TTT,

I also have all the new cab seals, door seals, etc....

Regards,

Stace

elk hunter · 11-11-2004, 04:22 PM

hows the dash pad?....need a nice tan or brown 81-91.

383drvr · 11-11-2004, 09:32 PM

I'd be interested in looking through it if its easy to see somewhere??? Might could find some usefull parts for my burb project. Where are you located in DFW? Thanks!

Staceydude · 11-11-2004, 10:36 PM

Hello,

Dash pad is not in good shape. I was going to recover it.

As far as selling any parts off of it. I am tryin to sell the whole truck first. I have a few people wanting to see it and I will be back in town late tomorrow night. I will post up what happens after the weekend.

Regards,

Stacey

Staceydude · 11-19-2004, 01:05 AM

Okay All,

I am going to drop the price on this thing to $300.00 Cash or trade for a few parts or whatever.

I lost track of some of the folks who were interested in looking at it.

Let me know if you are interested.

Regards,

Stacey

matt67350 · 11-19-2004, 11:24 AM

I'll take it.
PM me when you can.
thanks
Matthew

11-06-2004, 01:40 PM	#1
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	FOR SALE/TRADE... 81 K5 4X4 all or Parts, DFW TX lower price Hey All, I have done some deep thinking and knowing I am going to put a ton of money in whatever project I am building I have decided to get me a 67-72 truck.... So I will be selling my K5 whole or in parts... Basically it is a roller without tires/wheels It DOES not have a motor or tranny. However it does have a great NP208 transfer case with TH350 adapter. The was a smallblock truck. The body and frame are in great shape...Has alot of newer parts in it. Newer blower motor Newer Power steering box Mile Marker front hubs with good brakes front and rear Good radiator, front 10 bolt, rear 12 bolt Good AC condensor All lights except on front headlight worked great. Decent top with a few dings and a crack on one of the rails inside the truck could be fixed easily. Bucket seats and rear seats are there of course but the drivers seat needs recovered The interior is stripped out, door panels are gone, still have some of the original interior closeout panels for the cab abd rear section Stripped down tailgate with glass has zero rust Decent bumpers Good front fenders etc (front clip has been removed and is in the bed of truck with top on it in my garage) Hood is also in great shape In the attached pics you can see the primer along the bottom of the truck, it is virtually rust free, had a set of panels welded in just aft of the rear wheelwell. has a couple of small spots on the floor and bed area. Other than that the truck has been a Texas truck all its life. Has a good steering collumn with tile and no play whatsoever in the tilt. Has the original wheel that is near mint. Does need a windshield it is in but cracked. Basically I will ad more later as I think about it. I want to try and sell it all together first so I am only listing a comlete price.. If I part it (which would prolly make me some more money) I will list the indidual parts As you can see in the pics, this truck is very straight, other than the patched spots, all body panels are original. I will sell this truck for $300.00 I will take a few payments if someone wishes to give me a deposit and pay it off. couple hundred bucks at a time... May trade it for some tools... I need a small 110 Welder!!! Hobart handler or Lincoln weldpak etc. More pics on request.... I lost all my files on the CPU and will have to retake them... email or PM, staceybeller@charter.net Regards, Stacey Attached Images Last edited by Staceydude; 11-19-2004 at 01:43 AM.

11-11-2004, 04:22 PM	#6
elk hunter Registered User Join Date: Dec 2003 Location: oregon city, or Posts: 164	hows the dash pad?....need a nice tan or brown 81-91. __________________ yeah, but how's it wheel?

11-19-2004, 11:24 AM	#10
matt67350 Registered User Join Date: May 2001 Location: Benbrook, TX Posts: 1,060	I'll take it. PM me when you can. thanks Matthew __________________ 69 swb stepside, rebuild and upgrade in progress

11-06-2004, 02:22 PM	#2
smokinn Senior Member Join Date: Aug 2002 Location: omaha,Ne Posts: 617	man if i had a way of getting it here id give you the 400.00 for it. I could use some of them parts bad. Jason

11-06-2004, 11:43 PM	#4
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	Hey all, I have to go out of town this week to Montreal Canada for work. I will check the post and update it etc. but will not be here to show the truck. I also have a 73-75 winshield frame for a full convertible conversion I will let go for an extra $70.00 I am listing it seperatly. Regards, Stacey

11-07-2004, 01:45 AM	#5
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	TTT, I also have all the new cab seals, door seals, etc.... Regards, Stace

11-11-2004, 09:32 PM	#7
383drvr Registered User Join Date: Oct 2003 Location: Dallas, Tx. Posts: 308	I'd be interested in looking through it if its easy to see somewhere??? Might could find some usefull parts for my burb project. Where are you located in DFW? Thanks!

11-11-2004, 10:36 PM	#8
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	Hello, Dash pad is not in good shape. I was going to recover it. As far as selling any parts off of it. I am tryin to sell the whole truck first. I have a few people wanting to see it and I will be back in town late tomorrow night. I will post up what happens after the weekend. Regards, Stacey

11-19-2004, 01:05 AM	#9
Staceydude Registered User Join Date: Jun 2004 Location: DFW Area Texas Posts: 436	Okay All, I am going to drop the price on this thing to $300.00 Cash or trade for a few parts or whatever. I lost track of some of the folks who were interested in looking at it. Let me know if you are interested. Regards, Stacey



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.