69 SWB GMC for sale ...revisited (a 'lil cheaper) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Longhorn Man · 11-13-2004, 10:41 PM

Reduced price....$500...come and get it, could maybe deliver within 100 miles (that is a maybe) Another 100 bucks will get you the tow bar, safety chains and the tail light harness I made that hooks to a trailer plug on the tow vehicle.
Come and get it in columbus ohio, need a trailer or tow bar. Even though I can fire it up and move it, the headers are open and I'm selling it as not driveable.
Please answer w/questions, comments, pic requests...ect, on this thread, not in my PM box or e-mail. You'll get a quicker responce here anyways.
Payable w/cash,money order,postal money order...can store here for a short period of time, not very long though. It is dead and parked on the street

Selling

my short/fleet GMC (chevy front clip)

It does run, but knocks like crazy once warmed up. The TH350 bolted up to it was rebuilt in 97 and has maybe 30K on it sence then. Never slipped once, fluid been chainged every year...is leaking a little though. B&M 1900 RPM converter.
once piece drive shaft.
Hooker comp headers.

brand new t-stat housing...o-ring type, Mr Gasket brand. Edelbrock performer intake just cleaned, hand made alluminum block off plates for choke and EGR.
edelbrock 750/manual choke carb
manual drum brakes in need of help
big block engine towers. (dunno why, onless they were also V-6 towers)

power steering
clutch fan
wide belt drive off 87 burb on alt
Int reg alt
HEI
new-ish starter and fuel pump....
New-ish rad...kinda bent, but still works great.

rear coils w/3.07 gears ....VERY nice trailing arms. Probably the best you'll find in this part of the country...I think there is maybe a one inch spot where there is rust between the 2 halves...been a while since I looked...when I replaced the U-bolts...but none the less....very nice arms. While those shocks look terrible, They aren't all that old, and feel better than the 8 month old units up front.

the straight bumper that I kinda don't want to sell...but it is bolted there right now and I have no place to store it. It is an original '70 bumper, not repro. Minimal damage and wear...as an original used part, I would gove it an 8 or so out of 10.

It has mis matched rims..these are the front (notice the tread....dam near new tires up front) rims off a 70's jeep cherokee or something. Rear wheels....old turbines. Matching ones come up from time to time on e-bay...6 lug, 15 X 9.5 ...275/60 tires on the back...this is the drivers side...it still has tread, it is about 3 yrs old.

Note the (van) tilt, newer 4 spoke wheel, carpeting (kinda crappy...repro) in dash aftermarket acc guages (all work but the AMP, not hooked up) Nice 6 month old seat cover, over blue stock '70 seat. Seat is in decent shape, a spring or two need work and a cover...out of a 70 CST...so it is a non flip and full foam unit. Chevrolet rubber floor mats, couple soft spots on the floor, but no holes in floor that I am aware of. (You can see some light where kick panels meet the floor though) The bare foot pedal comes off...I'm keeping that. Working heat, working am/fm cassette pull out stereo with no speakers...you can hardly hear the radio anyways. Lots of crap in there that will be pulled out. (stuff on the floor and seat...not talkin parts)

Better pic of the seat cover. '70 CST door panels, were blue, dyed black, look almost decent

More can be seen on my OLD THREAD

Longhorn Man · 11-14-2004, 12:28 PM

make a great parts truck for some one in this part of the states...the solid trailing arms and goot TH350 alone are worth the asking price...not to mention a good intak, 750 AFB carb, tilt column, some real good tires, a 3.07 rear...

FRENCHBLUE72 · 11-14-2004, 01:31 PM

Andy if you were closer I would snag that thing up .....

Cethern · 11-14-2004, 01:37 PM

Andy
If I was closer it would be mine right now....Darn it!!

Longhorn Man · 11-14-2004, 09:49 PM

bumpin

longhorn71 · 11-14-2004, 09:54 PM

If i could get it here for cheap i would buy it.

Longhorn Man · 11-14-2004, 09:56 PM

you are only 2120 miles...come on over.
http://maps.yahoo.com/dd_result?ed=x...y=ca&oerr=3005

Burnsman · 11-14-2004, 10:17 PM

Anyway to tow it to my palce for extra $? If you were closer, I'd own it. I just don't trust my truck to make the trip (time for a newer one). My truck has some serious gremlins. I just barely made it back from North Carolina. I have to run to Rochester this weekend and I'm nervous enough that I am somehow going to have to load an S-10 with enough parts to fill my normal 8' bed. Should be a fun ride.......

Longhorn Man · 11-14-2004, 10:33 PM

I'd love to take another trip to PA...but my boss wouldn't go for it. YAHOO MAP
He'd be cool with 100 miles or less...and even that would be a rather big favor.

If only I could tow with the town car. (Anyone who's heard it run will laugh at that last comment)

Burnsman · 11-14-2004, 10:50 PM

Well, I'll be working on my truck this week. I'll see if I can't get the thing fixed. It's baffling quite a few of us (me and a couple of mechanics). It doesn't seem to be predictable. If not, maybe someone else would like to make some extra $??????

68C15 · 11-15-2004, 07:42 AM

NOTICE:
I am watching this with interest from the sidelines. if nobody snatches it up I just may have to do a roadtrip. how much extra for the tow-bar?

Longhorn Man · 11-15-2004, 04:52 PM

100 bucks will get you the tow bar, the tail light harness, and my safety chain. (the tow bar alone retails for 100 bucks...and it is dang near perfect)
Claim it now, and combine your 'lefty' with my shortie and come out the way you want.

CHEVYE · 11-15-2004, 05:37 PM

any possible trades/partial trades?

Longhorn Man · 11-15-2004, 05:44 PM

Not likely...I need cash in all reality...but you can try though.
What you got for trading materiel?

Longhorn Man · 11-15-2004, 09:27 PM

It has a full tank of gas in it...

grayw0lf · 11-15-2004, 09:32 PM

Man, if you were only closer! I've been working diligently on my truck for about 7 months now, & that truck still looks better.

Any chance your headin to AL anytime soon?

CHEVYE · 11-15-2004, 10:54 PM

will the tow bar work on a uhaul truck? i can`t think of anything for a partial trade, is there anything you need?

Longhorn Man · 11-15-2004, 11:25 PM

Tow bar will work with anything that has a 2 inch ball on it.

For anyone who is seriouse in wanting this, I just recieved a call from longhornjeff...he wants it too.

Quote:

Any chance your headin to AL anytime soon?

Sorry man, i have pretty much no reason to go to,nor through bama.

CHEVYE · 11-15-2004, 11:42 PM

pm`d ya

Longhorn Man · 11-16-2004, 12:06 AM

And returned.... sale pending...twice.
Sending another PM.

stllookn · 11-16-2004, 12:41 AM

I can't believe this has not sold! A short fleetside with an engine that starts for only $500!!!! What gives?

67ChevyC10Stepside · 11-16-2004, 01:10 AM

burnsman....i might be able to get my buddy to pic it up for you if you pay gas and such....we need to come up there any way to get my torque converter.....

67ChevyC10Stepside · 11-16-2004, 01:11 AM

also burnsman i tried calling you tonight...my buddy wants to know if you have a rear end with 3.73s or 4.10s you would sell?

Longhorn Man · 11-16-2004, 06:14 AM

Quote:

Originally Posted by stllookn

I can't believe this has not sold! A short fleetside with an engine that starts for only $500!!!! What gives?

Don't over look the fact that is is rough as hell.
I fired it up and moved it yesterday so i could cut the grass. Sounded pretty mean too.

dropdprpls10 · 11-16-2004, 02:08 PM

is that a 350 in there?? im going to ask the women if i can(shes a little anal about my toys) but i have another 350 sitting in my garage.. how is the cab look rusted through or still solid??

11-13-2004, 10:41 PM	#1
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	69 SWB GMC for sale ...revisited (a 'lil cheaper) Reduced price....$500...come and get it, could maybe deliver within 100 miles (that is a maybe) Another 100 bucks will get you the tow bar, safety chains and the tail light harness I made that hooks to a trailer plug on the tow vehicle. Come and get it in columbus ohio, need a trailer or tow bar. Even though I can fire it up and move it, the headers are open and I'm selling it as not driveable. Please answer w/questions, comments, pic requests...ect, on this thread, not in my PM box or e-mail. You'll get a quicker responce here anyways. Payable w/cash,money order,postal money order...can store here for a short period of time, not very long though. It is dead and parked on the street Selling my short/fleet GMC (chevy front clip) It does run, but knocks like crazy once warmed up. The TH350 bolted up to it was rebuilt in 97 and has maybe 30K on it sence then. Never slipped once, fluid been chainged every year...is leaking a little though. B&M 1900 RPM converter. once piece drive shaft. Hooker comp headers. brand new t-stat housing...o-ring type, Mr Gasket brand. Edelbrock performer intake just cleaned, hand made alluminum block off plates for choke and EGR. edelbrock 750/manual choke carb manual drum brakes in need of help big block engine towers. (dunno why, onless they were also V-6 towers) power steering clutch fan wide belt drive off 87 burb on alt Int reg alt HEI new-ish starter and fuel pump.... New-ish rad...kinda bent, but still works great. rear coils w/3.07 gears ....VERY nice trailing arms. Probably the best you'll find in this part of the country...I think there is maybe a one inch spot where there is rust between the 2 halves...been a while since I looked...when I replaced the U-bolts...but none the less....very nice arms. While those shocks look terrible, They aren't all that old, and feel better than the 8 month old units up front. the straight bumper that I kinda don't want to sell...but it is bolted there right now and I have no place to store it. It is an original '70 bumper, not repro. Minimal damage and wear...as an original used part, I would gove it an 8 or so out of 10. It has mis matched rims..these are the front (notice the tread....dam near new tires up front) rims off a 70's jeep cherokee or something. Rear wheels....old turbines. Matching ones come up from time to time on e-bay...6 lug, 15 X 9.5 ...275/60 tires on the back...this is the drivers side...it still has tread, it is about 3 yrs old. Note the (van) tilt, newer 4 spoke wheel, carpeting (kinda crappy...repro) in dash aftermarket acc guages (all work but the AMP, not hooked up) Nice 6 month old seat cover, over blue stock '70 seat. Seat is in decent shape, a spring or two need work and a cover...out of a 70 CST...so it is a non flip and full foam unit. Chevrolet rubber floor mats, couple soft spots on the floor, but no holes in floor that I am aware of. (You can see some light where kick panels meet the floor though) The bare foot pedal comes off...I'm keeping that. Working heat, working am/fm cassette pull out stereo with no speakers...you can hardly hear the radio anyways. Lots of crap in there that will be pulled out. (stuff on the floor and seat...not talkin parts) Better pic of the seat cover. '70 CST door panels, were blue, dyed black, look almost decent More can be seen on my OLD THREAD

11-14-2004, 01:31 PM	#3
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Andy if you were closer I would snag that thing up ..... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-14-2004, 01:37 PM	#4
Cethern What was I thinking?? Join Date: Dec 2003 Location: Commerce City Co Posts: 636	Andy If I was closer it would be mine right now....Darn it!! __________________ 72 K5 that needs lots of parts.. 71 GMC 3/4 4x4 That doesn't need much which is a good thing I don't think I could aford another money pit...

11-14-2004, 10:17 PM	#8
Burnsman Chevy Freak Join Date: Sep 2002 Location: Meadville, Pa. Posts: 2,804	truck Anyway to tow it to my palce for extra $? If you were closer, I'd own it. I just don't trust my truck to make the trip (time for a newer one). My truck has some serious gremlins. I just barely made it back from North Carolina. I have to run to Rochester this weekend and I'm nervous enough that I am somehow going to have to load an S-10 with enough parts to fill my normal 8' bed. Should be a fun ride....... __________________ 69 GMC SWB, 350 70 Chevy LWB, 350 55 chevy gasser, 461 73 Camaro, 496 67 RS Camaro, 406 64 Chevelle, 588 71 Nova, 565 67 Camaro, 461

11-14-2004, 10:50 PM	#10
Burnsman Chevy Freak Join Date: Sep 2002 Location: Meadville, Pa. Posts: 2,804	truck Well, I'll be working on my truck this week. I'll see if I can't get the thing fixed. It's baffling quite a few of us (me and a couple of mechanics). It doesn't seem to be predictable. If not, maybe someone else would like to make some extra $?????? __________________ 69 GMC SWB, 350 70 Chevy LWB, 350 55 chevy gasser, 461 73 Camaro, 496 67 RS Camaro, 406 64 Chevelle, 588 71 Nova, 565 67 Camaro, 461

11-14-2004, 12:28 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	make a great parts truck for some one in this part of the states...the solid trailing arms and goot TH350 alone are worth the asking price...not to mention a good intak, 750 AFB carb, tilt column, some real good tires, a 3.07 rear...

11-14-2004, 09:49 PM	#5
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	bumpin

11-14-2004, 09:54 PM	#6
longhorn71 Senior Member Join Date: Sep 2004 Location: CANADA Posts: 1,681	If i could get it here for cheap i would buy it.

11-14-2004, 09:56 PM	#7
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	you are only 2120 miles...come on over. http://maps.yahoo.com/dd_result?ed=x...y=ca&oerr=3005

11-14-2004, 10:33 PM	#9
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	I'd love to take another trip to PA...but my boss wouldn't go for it. YAHOO MAP He'd be cool with 100 miles or less...and even that would be a rather big favor. If only I could tow with the town car. (Anyone who's heard it run will laugh at that last comment)

11-15-2004, 07:42 AM	#11
68C15 blood type; Retumbo Join Date: Jan 2004 Location: next to my reloading bench Posts: 10,269	NOTICE: I am watching this with interest from the sidelines. if nobody snatches it up I just may have to do a roadtrip. how much extra for the tow-bar? __________________ Man rule #77...if you own a 67 stepside with a caddy 472 you will never be in danger of loosing you man card

11-15-2004, 04:52 PM	#12
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	100 bucks will get you the tow bar, the tail light harness, and my safety chain. (the tow bar alone retails for 100 bucks...and it is dang near perfect) Claim it now, and combine your 'lefty' with my shortie and come out the way you want.

11-15-2004, 05:37 PM	#13
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	any possible trades/partial trades? __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback Last edited by CHEVYE; 11-15-2004 at 05:40 PM.

11-15-2004, 05:44 PM	#14
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Not likely...I need cash in all reality...but you can try though. What you got for trading materiel?

11-15-2004, 09:27 PM	#15
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	It has a full tank of gas in it...



Register or Log In To remove these advertisements.

11-15-2004, 09:32 PM	#16
grayw0lf Registered User Join Date: Apr 2004 Location: Clanton, AL Posts: 1,253	Man, if you were only closer! I've been working diligently on my truck for about 7 months now, & that truck still looks better. Any chance your headin to AL anytime soon? __________________ 85' CUCV M1009!!! The newest addition! 6.2diesel, Th400, NP208, & only 36k miles! 70' C-10 LWB Fleetside - Looking good these days! 05' Dodge Neon 88' Winner Escape Sport 1750 - 4.3v6 94' Seadoo SP 84' Honda TRX200, bare nekkid. Just a frame & tires. Always looking for another project or any good deal!

11-15-2004, 10:54 PM	#17
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	will the tow bar work on a uhaul truck? i can`t think of anything for a partial trade, is there anything you need? __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

11-15-2004, 11:42 PM	#19
CHEVYE my gas saver Join Date: Sep 2003 Location: Clarksville, TN Posts: 2,046	pm`d ya __________________ 85' SWB, 4.3/TH350, getting ready for paint 84`SWB, 462ci./TH400, cowl hood, 15" billet spec., flows, blazer buckets/console, flat black 71`SWB, project ebay feedback

11-16-2004, 12:06 AM	#20
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	And returned.... sale pending...twice. Sending another PM.

11-16-2004, 12:41 AM	#21
stllookn Saving 1 truck at a time! Join Date: Aug 2001 Location: Kent, WA Posts: 6,465	I can't believe this has not sold! A short fleetside with an engine that starts for only $500!!!! What gives? __________________ '68 C20 Longhorn 50th Anniversary 400/TH400 '68 C20 Longhorn 50th Anniversary 468/TH400w/buckets '72 C20 Halfhorn (Longhorn w/o cab and front clip) '69 Flxible Cruiser (look up ugly in the dictionary)

11-16-2004, 01:10 AM	#22
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,032	burnsman....i might be able to get my buddy to pic it up for you if you pay gas and such....we need to come up there any way to get my torque converter..... __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

11-16-2004, 01:11 AM	#23
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,032	also burnsman i tried calling you tonight...my buddy wants to know if you have a rear end with 3.73s or 4.10s you would sell? __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

11-16-2004, 02:08 PM	#25
dropdprpls10 Registered User Join Date: Jun 2004 Location: Reading PA Posts: 164	is that a 350 in there?? im going to ask the women if i can(shes a little anal about my toys) but i have another 350 sitting in my garage.. how is the cab look rusted through or still solid?? __________________ 98% of ALL fords are still on the road today... .... the other 2% made it home!!! where is the best place to park a ford???.. next to a fire station!!!! pictures of my new and old trucks!

Register or Log In To remove these advertisements.