Body Mounts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Striker169 · 05-18-2005, 07:32 PM

How do the body mounts on the cab put together? I have the round rubber pieces and then these cone looking ones and the bolts and washers but how is it all susposed to piece together?

JimKshortstep4x4 · 05-18-2005, 07:56 PM

I am not sure how your kit is set up, but the round doughnut sets onto the frame mount with the protrusion down through the hole. The large washer goes on top of the doughnut. There should be a spacer (pipe) that fits into the doughnut and the tapered rubber part fits over the spacer with the small end down. When installed the two pieces of rubber sandwiches the frame mount so the large doughnut is on top and the tapered rubber is on the bottom.

On the rear mounts the bolt screws into the body from below through the setup with the smaller washer on the bolt.

On the front mounts the bolts go through the floor and through the mounts and there should be a nut for the bottom end along with a washer.

Jim

Striker169 · 05-18-2005, 08:23 PM

Quote:

Originally Posted by JimKshortstep4x4

I am not sure how your kit is set up, but the round doughnut sets onto the frame mount with the protrusion down through the hole. The large washer goes on top of the doughnut. There should be a spacer (pipe) that fits into the doughnut and the tapered rubber part fits over the spacer with the small end down. When installed the two pieces of rubber sandwiches the frame mount so the large doughnut is on top and the tapered rubber is on the bottom.

On the rear mounts the bolt screws into the body from below through the setup with the smaller washer on the bolt.

On the front mounts the bolts go through the floor and through the mounts and there should be a nut for the bottom end along with a washer.

Jim

Thats exactly what I needed to know THANK YOU SO MUCH!

TruckinDaddy · 05-20-2005, 01:09 AM

Got it mounted yet? Did you end up switching to the high hump?

blazerparts · 05-20-2005, 10:54 AM

doughnuts.........sandwiches.........I'm getting hungry

Striker169 · 05-20-2005, 05:51 PM

Quote:

Originally Posted by TruckinDaddy

Got it mounted yet? Did you end up switching to the high hump?

Nah with the mounts we didnt end up needing to go high hump and I mounted it yesterday I am gonna fix the distributer today and get all the wireing out of the old cab and the glass today/tomorrow so hopefully I can drive it around the block by saturday evening.

05-18-2005, 07:32 PM	#1
Striker169 Car O'Holic Join Date: Jan 2005 Location: Austin, Tx. Posts: 692	Body Mounts How do the body mounts on the cab put together? I have the round rubber pieces and then these cone looking ones and the bolts and washers but how is it all susposed to piece together?

05-20-2005, 01:09 AM	#4
TruckinDaddy What's that funky smell? Join Date: Mar 2005 Location: Austin, TX Posts: 610	Got it mounted yet? Did you end up switching to the high hump? __________________ Mike S 68 C10 Long Step (Pretending to be a Long Fleetside) Grandpa's Farm Truck 3 on the tree, 307, No power brakes or steering Factory Options - HD rear spring and Ammeter/Oil Gauges My truck blog My Car Domain page

05-20-2005, 10:54 AM	#5
blazerparts No,I DON'T have Tourett's Join Date: Mar 2005 Location: Reno, NV Posts: 556	doughnuts.........sandwiches.........I'm getting hungry __________________ '72 K5 CST 350/350 Daily Driver '69 GMC3500 Camper Special CST Flatbed 396/400 Upgraded to show truck '69 GMC 2500 L6292, 3spd beater

05-18-2005, 07:56 PM	#2
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	I am not sure how your kit is set up, but the round doughnut sets onto the frame mount with the protrusion down through the hole. The large washer goes on top of the doughnut. There should be a spacer (pipe) that fits into the doughnut and the tapered rubber part fits over the spacer with the small end down. When installed the two pieces of rubber sandwiches the frame mount so the large doughnut is on top and the tapered rubber is on the bottom. On the rear mounts the bolt screws into the body from below through the setup with the smaller washer on the bolt. On the front mounts the bolts go through the floor and through the mounts and there should be a nut for the bottom end along with a washer. Jim



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.