WANTED Bedfloor piece - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jesse72 · 06-06-2005, 06:16 PM

I am in need of a piece of original bed floor from a 67-72 would prefer a back section but anything will do surface rust is ok just no holes. Doesnt' have to be huge but i need to patch a few holes up, let me know what you have.

Thanks,Jesse

Jesse72 · 06-07-2005, 02:40 PM

bump I am in need of a piece quick and just a note i dont need the whole floor

**JIMs70GMC** · 06-07-2005, 02:59 PM

PM Randy70c-10, he has a bed in his backyard.

Jakes-66-K10 · 06-07-2005, 03:02 PM

Try www.americanclassic.com I know they sell patch panels like this. I know I've seen them at other vendors too.

chevyfarmer · 06-07-2005, 03:16 PM

I do not know about everyone else, but I tried some aftermarket patch panels for the bed floor and they did not fit to well @ all. The ribs did not line up they were different depths & widths. I would try to score a original piece if you could, it might be worth the wait. Just my .02

Jesse72 · 06-08-2005, 09:57 PM

I second chevyfarmer i bought a goodmark piece and it was thin and no where near fit.

06-06-2005, 06:16 PM	#1
Jesse72 Registered User Join Date: Jan 2005 Location: Ohio Posts: 171	WANTED Bedfloor piece I am in need of a piece of original bed floor from a 67-72 would prefer a back section but anything will do surface rust is ok just no holes. Doesnt' have to be huge but i need to patch a few holes up, let me know what you have. Thanks,Jesse __________________ Jesse 72 4x4 Sold 59 GMC air ride ls swap

06-07-2005, 02:40 PM	#2
Jesse72 Registered User Join Date: Jan 2005 Location: Ohio Posts: 171	bump I am in need of a piece quick and just a note i dont need the whole floor __________________ Jesse 72 4x4 Sold 59 GMC air ride ls swap Last edited by Jesse72; 06-07-2005 at 02:41 PM.

06-07-2005, 02:59 PM	#3
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	PM Randy70c-10, he has a bed in his backyard. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

06-07-2005, 03:16 PM	#5
chevyfarmer Registered User Join Date: Feb 2005 Location: Owosso, Mi Posts: 242	I do not know about everyone else, but I tried some aftermarket patch panels for the bed floor and they did not fit to well @ all. The ribs did not line up they were different depths & widths. I would try to score a original piece if you could, it might be worth the wait. Just my .02 __________________ 67 short wide 355ci 3 on tree 69 short wide 250ci 3 on tree 68 long wide 283 3 on tree 72 2wd Blazer project 454 5 speed

06-08-2005, 09:57 PM	#6
Jesse72 Registered User Join Date: Jan 2005 Location: Ohio Posts: 171	I second chevyfarmer i bought a goodmark piece and it was thin and no where near fit. __________________ Jesse 72 4x4 Sold 59 GMC air ride ls swap

06-07-2005, 03:02 PM	#4
Jakes-66-K10 Registered User Join Date: Aug 2004 Location: Idaho Posts: 640	Try www.americanclassic.com I know they sell patch panels like this. I know I've seen them at other vendors too.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.